User’s Manual Monochrome LCD Monitor It shall be assured that the final system is in compliance to IEC60601-1-1 requirements.
English SAFETY SYMBOLS This manual uses the safety symbols below. They denote critical information. Please read them carefully. WARNING Failure to abide by the information in a WARNING may result in serious injury and can be life threatening. CAUTION Failure to abide by the information in a CAUTION may result in moderate injury and/or property or product damage. Indicates a prohibited action. Indicates to ground for safety.
English TABLE OF CONTENTS PRECAUTIONS ................................................................................... 4 1. INTRODUCTION ..................................................................................... 9 1-1. Features ........................................................................................................9 1-2. Package Contents..........................................................................................9 1-3. Controls & Connectors .......................
English PRECAUTIONS IMPORTANT! • This product has been adjusted specifically for use in the region to which it was originally shipped. If operated outside the region to which it was originally shipped, the product may not perform as stated in the specifications. • To ensure personal safety and proper maintenance, please read this section and the caution statements on the unit (refer to the figure below).
English WARNING If the unit begins to emit smoke, smells like something is burning, or makes strange noises, disconnect all power connections immediately and contact your dealer for advice. Attempting to use a malfunctioning unit may result in fire, electric shock, or equipment damage. Do not open the cabinet or modify the unit. Opening the cabinet or modifying the unit may result in fire, electric shock, or burn. Refer all servicing to qualified service personnel.
English WARNING To avoid danger of suffocation, keep the plastic packing bags away from babies and children. Use the enclosed power cord and connect to the standard power outlet of your country. Be sure to remain within the rated voltage of the power cord. Not doing so may result in fire or electric shock. To disconnect the power cord, grasp the plug firmly and pull. Tugging on the cord may damage and result in fire or electric shock. The equipment must be connected to a grounded main outlet.
English WARNING When attaching an arm stand, please refer to the user’s manual of the arm stand and install the unit securely with the enclosed screws. Not doing so may cause the unit to become unattached, which may result in injury or equipment damage. When the unit is dropped, please ask your dealer for advice. Do not continue using a damaged unit. Using a damaged unit may result in fire or electric shock. When reattaching the tilt stand, please use the same screws and tighten them securely.
English CAUTION Do not touch the plug with wet hands. Doing so may result in electric shock. Use an easily accessible power outlet. This will ensure that you can disconnect the power quickly in case of a problem. Periodically clean the area around the plug. Dust, water, or oil on the plug may result in fire. Unplug the unit before cleaning it. Cleaning the unit while it is plugged into a power outlet may result in electric shock.
English 1. INTRODUCTION Thank you very much for choosing an EIZO Monochrome Monitor. 1-1. Features • DVI (p.31) Digital input (TMDS (p.31)) compliant • [Resolution] 2M pixels (1600 dots × 1200 lines) [Horizontal scanning frequency] 75 kHz [Vertical scanning frequency] 60 Hz • USB (Universal Serial Bus) hub supported (p.20) • The height adjustable stand incorporated • Ultra slim bezel incorporated • Power saving function (p.18) (DVI-DMPM(p.
English 1-3.
English Rear (9) (10) (11) (7) (8) (12) Side Height Adjustable Stand (Detachable) * 3 (7) (8) (9) (10) Security Lock Slot *4 USB Port (1 Upstream) USB Port (2 Downstream) (11) DVI-D Input Connector (12) Power Connector *3 *4 The LCD monitor has the capability of the Portrait/Landscape display. (The panel pivots in the clockwise direction 90°.) The LCD monitor can be used with an optional arm stand by removing the stand (p.22). Allows for connection of a security cable.
English 2. CABLE CONNECTION NOTE • Be sure that the power switches of both the PC and the monitor are OFF. • Please refer to the manual of the PC also to connect the monitor. 1. Pivot the panel in the counter-clockwise to fix in portrait position. 2. Plug the signal cable into the connector at the rear of the monitor and the other end of the cable into the video connector on the PC. After connecting, secure the connection with the screw-in fasteners.
English 4. Lead the power cord and signal cable into the cable holder at rear of the monitor. NOTE • When housing the cables into the cable holder, lead them to the cable entrance side and pinch the projection to open the cable entrance. • The cables are recommended to lead with slight sag for the smooth motion of the stand. Projection Cable Holder 5. Cable Entrance Plug the other end of the power cord into a power outlet.
English 6. Turn on the monitor’s Power Button and then switch on the PC’s power. The monitor’s power indicator will light up (green). If an image does not appear, refer to the “6. TROUBLESHOOTING” (p.24) for advice. Whenever finished, turn off the PC and the monitor. 7. Set the kind of graphics card. “8bit” of “Monochrome” (the 8bit monochrome graphics card) is set as default.
English 3. ScreenManager 3-1. How to use the ScreenManager ScreenManager Main Menu Enter Button 1. Control Buttons Left, Down, Up, Right Entering the ScreenManager Press the Enter Button once to display the main menu of the ScreenManager. 2. Making Adjustments and Settings (1) Select the desired sub menu icon using the Control Buttons and press the Enter Button. The sub menu appears. (2) Use the Control Buttons to select the desired setting icon and press the Enter Button. The setting menu appears.
English 3-2. ScreenManager Adjustments and Settings The following table shows all the ScreenManager’s adjustment and setting menus. Main menu Screen Sub menu Reference *1 Brightness Control the brightness for the entire screen. Unlock Unlock the lock. (p.18) *2 LUT Setting Default / Normal / Custom Set the LUT (Look-up table) (p.31) setting. PowerManager DVI DMPM 3-4. Power-save Setup. (p.19) Others Off Timer Set the monitor’s off timer to on or off. (p.
English 3-3. Useful Functions Adjustment Lock Use the “Adjustment Lock” function to prevent any accidental changes. Locked function • Settings in the ScreenManager. • Adjustment of brightness by the Control Buttons. [How to lock] (1) Switch off the monitor’s power by the power button on the control panel. (2) Press on the Enter button while switching on the monitor’s power. [How to unlock] (1) Switch off the monitor’s power by the power button on the control panel.
English Unlock Function after Calibration The calibration is available when using the specified optional calibration kit (p.29). After the calibration, the functions below are automatically locked. Locked function • Brightness adjustment (including the adjustment by Left and Right Buttons on the control panel) • LUT Setting Unlock function is available by using ScreenManager. [How to unlock] (1) Select the of menu. (2) Select “Unlock”.
English 3-4. Power-save Setup The menu in the ScreenManager enables to set the power-save setup. NOTE • Do your part to conserve energy, turn off the monitor when you are finished using it. Disconnecting the monitor from the power supply is recommended to save energy completely. • Even if the monitor is in a power saving mode, USB compliant devices function when they are connected to the monitor’s USB (both the upstream and the downstream ports).
English 4. MAKING USE OF USB (Universal Serial Bus) This monitor provides a hub which supports the USB standard. When connecting to a USB compliant PC or another hub, the monitor functions as a hub to which the USB compliant peripherals can be easily connected. Required system environment • PC with build-in USB ports or another USB hub connected to the USB compliant PC • EIZO USB Cable (MD-C93) NOTE • The USB hub function may not work properly depending on the PC or peripherals.
English 3. After setting up, the monitor’s USB hub is available for connecting USB compliant peripherals to the downstream ports of the monitor. Connecting Examples Monitor PC Keyboard Mouse Printer Downstream Ports: Printer Keyboard Connect the cables from USB compliant peripherals such as a mouse, keyboard, etc. Downstream Ports 4.
English 5. ATTACHING AN ARM The LCD monitor can be used with an arm by removing the tilt stand and attaching the arm or stand to the LCD monitor. NOTE • If you will use the arm or stand of other companies, confirm the followings to the arm or stand maker before selecting.
English 4. Attach an arm stand to the LCD monitor securely. Arm-stand 4 Mounting Screws: M4 × 10 (mm) 5.
English 6. TROUBLESHOOTING If a problem persists even after applying the suggested remedies, contact an EIZO dealer. • No picture problems → See No.1 - No.2 • Imaging problems → See No.3 - No.7 • Other problems → See No.8 - No.9 • USB problems → See No.10 - No.11 Problems 1. No picture • Indicator status: Off • Indicator status: Green • Indicator status: Orange • Indicator status: Slowly flashing Orange Check that the power cord is correctly connected.
English Problems Points to check with possible solutions 4. The screen is too bright or too dark. Adjust the . (The backlight of the LCD monitor has a fixed life span. When the screen becomes dark or begins to flicker, please contact your dealer.) 5. Afterimages appear. When the screen image is changed after displaying the same image for a long period, an afterimage may appear. The “Afterimage” can be removed gradually by changing the displayed image.
English Problems 11. PC is hung up. / The peripherals connected to the downstream ports do not operate. 26 6. TROUBLESHOOTING Points to check with possible solutions Check that the USB cable is correctly connected. Check the downstream ports by connecting the peripherals to other downstream ports. If the problem is solved by doing this, contact an EIZO dealer. (For details, refer to the manual of the PC.) Try executing the following method.
English 7. CLEANING Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime. NOTE • Never use thinner, benzene, alcohol (ethanol, methanol, or isopropyl alcohol), abrasive cleaners, or other strong solvents, as these may cause damage to the cabinet or LCD panel. Cabinet To remove stains, wipe the cabinet with a soft, lightly moistened cloth using a mild detergent. Do not spray wax or cleaner directly into the cabinet.
English 8. SPECIFICATIONS LCD Panel 50 cm (19.6 inch), TFT Monochrome LCD panel Anti-Glare Hard Coating 3H, Response Time: approx. 40 ms Viewing Angle Horizontal: 170°, Vertical: 170° (CR≥10) Dot Pitch 0.249 mm Horizontal Scan Frequency 75 kHz (only exclusive timing supported) Vertical Scan Frequency 60 Hz (only exclusive timing supported) Resolution 2M pixels (1600 dots × 1200 lines) Dot Clock 162 MHz Gray Scale 1024 steps of 3061 steps Display Area 398.4 mm (H) × 298.8 mm (V) (15.
English Dimensions mm (inches) 3(0.12) 52(2.05) 8(0.31) N 493(19.4) 272.5(10.7) 168(6.6) 400.4(15.8) 441(17.4) IO 325.5(12.8) 3(0.12) 82(3.23) T TA RO 575(22.6) 78.5(3.09) 55(2.17) 6.5(0.26) 15.5(0.61) 301.5(11.9) 337(13.3) 300.8(11.8) 3(0.12) 3(0.12) 27(1.06) 208.5(8.
English Pin Assignment DVI-D Connector 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Pin No. Signal Pin No. Signal Pin No.
English 9. GLOSSARY Afterimage The Afterimage is particular to LCD monitors when the monitor screen is left on for a long period without use. The “Afterimage” can be removed gradually by changing the displayed image. DVI (Digital Visual Interface) A digital flat panel interface. DVI can transmit digital data from the PC directly without loss with the signal transition method “TMDS”. There are two kinds of DVI connectors. One is DVI-D connector for digital signal input only.
For U.S.A, Canada, etc. (rated 100-120 Vac) Only This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
