User’s Manual Monochrome LCD Monitor It shall be assured that the final system is in compliance to IEC60601-1-1 requirements.
English SAFETY SYMBOLS This manual uses the safety symbols below. They denote critical information. Please read them carefully. WARNING Failure to abide by the information in a WARNING may result in serious injury and can be life threatening. CAUTION Failure to abide by the information in a CAUTION may result in moderate injury and/or property or product damage. Indicates a prohibited action. Indicates to ground for safety.
English TABLE OF CONTENTS PRECAUTIONS .................................................................................... 4 1. INTRODUCTION ..................................................................................... 9 1-1. Features ........................................................................................................9 1-2. Package Contents..........................................................................................9 1-3. Controls & Connectors ......................
English PRECAUTIONS IMPORTANT! • This product has been adjusted specifically for use in the region to which it was originally shipped. If operated outside the region to which it was originally shipped, the product may not perform as stated in the specifications. • To ensure personal safety and proper maintenance, please read this section and the caution statements on the unit (refer to the figure below).
English WARNING If the unit begins to emit smoke, smells like something is burning, or makes strange noises, disconnect all power connections immediately and contact your dealer for advice. Attempting to use a malfunctioning unit may result in fire, electric shock, or equipment damage. Do not open the cabinet or modify the unit. Opening the cabinet or modifying the unit may result in fire, electric shock, or burn. Refer all servicing to qualified service personnel.
English WARNING To disconnect the power cord, grasp the plug firmly and pull. Tugging on the cord may damage and result in fire or electric shock. The equipment must be connected to a grounded main outlet. Not doing so may result in fire or electric shock. Use the correct voltage. * The unit is designed for use with a specific voltage only. Connection to another voltage than specified in this User’s Manual may cause fire, electric shock, or equipment damage.
English WARNING Do not touch a damaged LCD panel directly with bare hands. The liquid crystal which leaks from the panel is poisonous if it enters the eyes or mouth. If any part of the skin or body comes in direct contact with the panel, please wash thoroughly. If some physical symptoms result, please consult your doctor. Follow local regulation or laws for safe disposal. The backlight of the LCD panel contains mercury. CAUTION Handle with care when carrying the unit.
English LCD Panel The screen may have defective pixels. These pixels may appear as slightly light or dark area on the screen. This is due to the characteristics of the panel itself, and not the product. The backlight of the LCD panel has a fixed life span. When the screen becomes dark or begins to flicker, please contact your dealer. Do not press on the panel or edge of the frame strongly, as this may result in damage to the screen.
English 1. INTRODUCTION Thank you for choosing an EIZO Monochrome Monitor. 1-1. Features • DVI Digital input compliant (p.30 ; for TMDS, p.30) • [Horizontal scanning frequency] [Vertical scanning frequency] [Resolution] 103.9 ± 4 kHz 50.06 ± 3 Hz 5M pixels (Portrait: 2048 × 2560 dots (H × V)) • USB (Universal Serial Bus) hub support (p.
English 1-3.
English Side / Rear (5) (6) USB upstream port (x 1) USB downstream ports (x 2) (7) DVI-D input connector (8) Power connector (9) Security lock slot*3 (10) Monitor stand with adjustable height (detachable) *4 Main Power Switch (11) *3 Allows for connection of a security cable. This lock supports Kensington’s MicroSaver security system. For further information, please consult : Kensington Technology Group 2855 Campus Drive, San Mateo, CA 94403 USA Tel.
English 2. CABLE CONNECTIONS NOTE • Be sure that the power switches of both the PC and the monitor are OFF. • Refer also to the PC user's manual when connecting the monitor. 1. Rotate the monitor ninety degrees counter-clockwise into the portrait position. 2. Connect the signal cable to the DVI-D input connector on the rear of the monitor and to the video output connector on the PC. After connecting, secure the cable connectors with the attached screw-in fasteners.
English 3. Connect the power cord to the power connector on the rear of the monitor. 4. Thread the power cord and signal cable through the cable holder on the rear of the monitor stand. NOTE • When threading the cables through the cable holder, lead them to the cable entrance side and pinch the projection to open the cable entrance. • It is recommended that some slack be left in the cables to allow for smooth adjustment of the monitor stand and easy rotation between the portrait and landscape positions.
English 7. Turn on the PC’s power. If an image does not appear, refer to “6. TROUBLESHOOTING” (p.23) for additional advice. When finished, turn off the PC and the monitor. NOTE • Adjust the brightness of the screen depending on the brightness of your environment. • Be sure to take adequate rests. A 10-minute rest period each hour is suggested. 8. When using the software "ScreenManager Pro for Medical," connect the monitor to a USB compliant Windows computer (or other USB hub) with a USB cable.
English 3. MENUS & FUNCTIONS 3-1. ScreenManager Screen adjustments and settings can be performed with the monitor controls. ScreenManager main menu Directing Switches Left, Down, Up, Right Enter Switch How to use the ScreenManager [Entering the ScreenManager] (1) Touch the enter switch. [Making adjustments and settings] (1) Select the desired submenu icon with the directing switches and touch the enter switch. (2) Select the desired setting icon with the directing switches and touch the enter switch.
English ScreenManager Menus and Settings The following table briefly explains each of the menus and settings in the ScreenManager. Main menu Screen Sub menu *1 Brightness Reference Control the brightness for the entire screen. Unlock Unlock the locked functions. (p.18) Default / Normal *2 / Custom*3 Set the LUT (Look-up table) (p.30) setting. PowerManager DVI DMPM Refer to “3-3. Power-save Setup” (p.19). Others Off Timer Turn off the monitor after a specified time. (p.
English 3-2. Other Useful Functions Adjustment Lock Use this function to prevent any accidental changes to the monitor settings. The following table shows which functions the adjustment lock affects. Locked functions • Display, adjustment, and setting of the ScreenManager • Adjustment of brightness by the Directing Switch [How to lock] (1) Turn off the monitor power by touching the power switch. (2) Touch the power switch while touching the enter switch.
English Power Indicator Use the function to keep the power indicator without light while the monitor is operational. (The power indicator is set by default to light when the power is turned on.) [Procedure] (1) Select in the ScreenManager menu. (2) Select “Disable”. Unlock Function after Calibration The calibration is available by using the specified optional calibration kit (p.28). After the calibration, the functions below are automatically locked.
English 3-3. Power-save Setup Use the menu in the ScreenManager to configure the power-save setup. This monitor complies with the “DVI DMPM” (p.30). NOTE • Do your part to conserve energy, turn off the monitor when you are finished using it. Disconnecting the monitor from the power supply is recommended to save energy completely. • Even if the monitor is in power-saving mode, USB compliant devices draw power when they are connected to the monitor's USB ports (both upstream and downstream).
English 4. MAKING USE OF USB (UNIVERSAL SERIAL BUS) This monitor provides a hub which supports the USB standard. When connecting to a USB compliant PC or another hub, the monitor functions as a hub to which the USB compliant peripherals can be easily connected. Required system environment • PC equipped with USB ports or another USB hub connected to the USB compliant PC • Windows 98/2000/Me/XP // Mac OS 8.5.
English 3. After setting up, the monitor's USB hub is available for connecting USB compliant peripherals to the downstream ports of the monitor. Connecting Examples Monitor Mouse PC Keyboard Downstream ports: Connect the cables from USB compliant peripherals such as a mouse, keyboard, etc. ScreenManager Pro for Medical (for Windows) For further details about the “ScreenManager Pro for Medical (for Windows)”, refer to the EIZO LCD Utility Disk. 4.
English 5. ATTACHING AN ARM The LCD monitor can be used with an arm by removing the tilt stand and attaching the arm or stand to the LCD monitor. NOTE • If you will use the arm or stand of other manufacturers, confirm the followings to the manufacturers before selecting.
English 6. TROUBLESHOOTING If a problem persists even after applying the remedies suggested below, contact an EIZO dealer. • No picture problems → See No.1 ~ No.2 • Imaging problems → See No.3 ~ No.6 • Other problems → See No.7 ~ No.9 • USB problems → See No.10 ~ No.11 Problem 1. No picture • Indicator status: Off 2. Points to check and possible solutions Check that the power cord is connected correctly.
English Problem Points to check and possible solutions 6. Fingerprints remain on the screen. Leaving the screen white may solve the problem. 7. The following message appears and the adjustment controls are not available when touching the switches on the control panel. After the calibration, the functions like brightness are automatically locked. Please refer to p.18 to unlock. 8. The ScreenManager main menu does not operate. Make sure that the adjustment lock is off (p.17).
English Problem 11. The PC freezes. The peripherals connected to the USB downstream ports do not operate. Points to check and possible solutions Check that the USB cable is connected correctly. Try connecting the peripheral to another USB downstream port. If the problem is solved by doing this, contact an EIZO dealer. (For details, refer to the manual of the PC.) Try executing the following method.
English 7. CLEANING Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime. NOTE • Never use thinner, benzene, alcohol (ethanol, methanol, or isopropyl alcohol), abrasive cleaners, or other strong solvents, as these may cause damage to the cabinet or LCD panel. • Make sure to turn off the monitor before cleaning it. Cabinet To remove stains, wipe the cabinet with a soft, lightly moistened cloth using a mild detergent.
English 8. SPECIFICATIONS LCD Panel GS510-BL GS510-CL 54 cm (21.3 inch), TFT Monochrome LCD panel Anti-Glare Hard Coating 2H, Response Time : approx 50ms GS510-BLG GS510-CLG 54 cm (21.3 inch), TFT Monochrome LCD panel Hard Coating 3H, Response Time : approx 50ms Viewing Angle Horizontal: 170°, Vertical: 170° (CR≥10) Dot Pitch 0.165 mm Horizontal Scan Frequency 103.9 ± 4 kHz (only exclusive timing supported) Vertical Scan Frequency 50.
English Dimensions mm (inches) Side Front Top Default Settings Brightness Fixed at the factory Orientation Portrait PowerManager DVI DMPM Off Timer Menu Settings Disable Menu Position Center Menu Off Timer Language 45 seconds English Optional Panel Protector EIZO “RP-901” Arm, Stand EIZO EIZO EIZO EIZO Graphics board 8bit and 10bit monochrome signals supported “LS-HM1-D”: Dual Height Adjustable Stand “LA-131-D” : LCD Monitor Flexible Arm “LA-030-W” : Wall Mount Arm for LCD Monitor “LA
English Pin Assignment DVI-D Connector 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Pin No. Signal Pin No. Signal Pin No.
English 9. GLOSSARY DVI (Digital Visual Interface) A digital flat panel interface. DVI can transmit digital data without loss and directly from the PC using the signal transition method “TMDS” (p.30). There are two kinds of DVI connectors: the DVI-D connector for digital signal input only, and the DVI-I connector for both digital and analog signal inputs. DVI DMPM (DVI Digital Monitor Power Management) The Power management system for the digital interface.
For U.S.A, Canada, etc. (rated 100-120 Vac) Only FCC Declaration of Conformity We, the Responsible Party EIZO NANAO TECHNOLOGIES INC. 5710 Warland Drive, Cypress, CA 90630 Phone: (562) 431-5011 declare that the product Trade name: EIZO Model: RadiForce GS510 is in conformity with Part 15 of the FCC Rules.
Recycling Information for customers in EU: All recycling information is placed in the following websites. Recycling-Information für Kunden in Europa: Alle Informationen zum Thema Recycling finden Sie auf den folgenden Websites: Informations sur le recyclage pour les clients dans l'UE: Vous trouverez toutes les informations sur le recyclage dans les sites Web suivants: Återvinningsinformation för kunder i EU: All information om återvinning finns på följande webbsidor: http://www.swico.ch http://www.eizo.
