Important Please read PRECAUTIONS, this User’s Manual, and the Setup Guide (separate volume) carefully to familiarize yourself with safe and effective usage. • Please refer to the Setup Guide for basic information ranging from connection of the monitor to a PC to using the monitor. • The latest User’s Manual is available for download from our web site: http://www.eizo.
Location of Caution Statement EV2316W / EV2336W (Ex.FlexStand2) EV2416W / EV2436W (Ex.FlexStand2) This product has been adjusted specifically for use in the region to which it was originally shipped. If operated outside this region, the product may not perform as stated in the specifications. No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
Notice for this monitor This product is suited to general purposes like creating documents, viewing multimedia content. This product has been adjusted specifically for use in the region to which it was originally shipped. If the product is used outside the region, it may not operate as specified in the specifications. This product may not be covered by warranty for uses other than those described in this manual.
Cleaning Attention • Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet or panel, and also quality deterioration of the image. • Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the cabinet or panel. Note • The optional ScreenCleaner is recommended for cleaning the cabinet and panel surface. If necessary, the stains on the cabinet and panel surface can be removed by moistening part of a soft cloth with water.
CONTENTS Cover....................................................................... 1 Chapter 3 Notice for this monitor.......................................... 3 3-1. Adjusting Volume.........................................31 Cleaning..................................................................... 4 3-2. Selecting sound source while using the DisplayPort signal input..............................31 3-3. Compensating viewing angle deficiency (EV2316W / EV2416W only)........................
●●To switch among input signals........................51 ●●To set input signal selection............................52 6-5. Making Use of USB (Universal Serial Bus)................................................................ 52 ●●Required System Environment.......................52 ●●Connection Procedure (Setup of USB Function)......................................................... 53 6-6. Displaying Monitor Information................. 53 6-7. Specifications..................................
Chapter 1 Introduction Thank you very much for choosing an EIZO color LCD monitor. 1-1. Features • • • • • • 23.0″ wide format LCD (EV2316W / EV2336W) 24.
*2 Reference values: EV2316W Maximum power consumption: 43 W (Brightness Max., when a USB device is connected, speaker working, at default settings) Standard power consumption: 14 W (Brightness 120 cd/m 2, when no USB device is connected, speaker not working, at default settings) EV2336W Maximum power consumption: 40 W (Brightness Max.
1-2. Controls and Functions ●●Front Setting menu*1 1 2 Setting menu*1 3 4 5 6 7 8 9 1 2 3 4 FlexStand2 5 6 7 8 9 TriStand2 1. EcoView Sense sensor Detects the movement of a person in front of the monitor (EcoView Sense function (page 38)). 2. Ambient light sensor Detects ambient brightness (Auto EcoView function (page 37)). 3. Displays the setting menu of the power saving function (Auto EcoView (page 37) and EcoView Optimizer 2 (page 38)) and EcoView Sense (page 38). button 4.
●●Rear 15 13 16 15 17 18 19 13 20 16 17 18 19 20 14 14 21 21 *3 1011 12 1011 FlexStand2 12 TriStand2 10. Main power switch Turns the main power on or off. 11. Power connector Connects the power cord. 12. Input signal connector Left: DisplayPort connector / Center: DVI-D connector / Right: D-Sub mini15-pin connector 13. Security lock slot Complies with Kensington’s MicroSaver security system. 14. Speaker Outputs audio source. Handle used for transportation 15.
1-3. EIZO LCD Utility Disk An “EIZO LCD Utility Disk” (CD-ROM) is supplied with this product. The following table shows the disk contents and the overview of the software programs. ●●Disk contents and software overview The disk includes software programs for adjustment, and User’s Manual. Refer to Readme.txt file on the disk for software startup procedures or file access procedures.
1-4. Basic Operations and Functions ●●Basic operation of the Setting menu 1. Displaying the Setting menu 1. Press . The Setting menu appears. 2. Adjusting / Setting 1. Choose a menu to adjust / set with , , and then press . The Sub menu appears. 2. Choose an item to adjust / set with , , and then press . The adjustment / setting menu appears. 3. Adjust / set the selected item with , , and then press 3. Exiting 1. Choose “Return” from the Sub menu and press 2.
●●Functions The following table shows the Setting menu and setting items of each menu. Main menu Color*1 Screen Sound Setting Brightness Contrast Temperature Gamma Advanced Settings Reference “2-3. Adjusting Color” (page 19) Saturation Hue Overdrive*2 Gain Color Reset Screen Size Smoothing Analog Adjustment*3 Auto Screen Adjust Auto Range Adjust Clock Phase Hor.Position Ver.Position Source “To reset the color adjustments” (page 35) “Screen Size Changing” (page 29) “2-4.
Chapter 2 Adjusting Screens 2-1. Compatible Resolutions The monitor supports the following resolutions. ●●EV2316W Analog Input (D-Sub) Resolution Applicable Signals 640 × 480 800 × 600 1024 × 768 1280 × 720 1280 × 960 1280 × 1024 1680 × 1050 1920 × 1080*1 VGA VESA VESA CEA-861 VESA VESA VESA CVT, VESA CVT RB CEA-861 Vertical Scan Frequency Dot Clock 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 148.5 MHz (Max.
●●EV2336W Analog Input (D-Sub) Resolution Applicable Signals 640 × 480 720 × 400 800 × 600 1024 × 768 1280 × 720 1280 × 960 1280 × 1024 1680 × 1050 1920 × 1080*1 VGA, VESA VGA TEXT VESA VESA CEA-861 VESA VESA VESA CVT, VESA CVT RB CEA-861 Vertical Scan Frequency Dot Clock ~75 Hz 70 Hz ~75 Hz ~75 Hz 60 Hz 60 Hz ~75 Hz 60 Hz 60 Hz 148.5 MHz (Max.
●●EV2416W Analog Input (D-Sub) Resolution Applicable Signals 640 × 480 800 × 600 1024 × 768 1280 × 720*1 1280 × 960 1280 × 1024 1600 × 1200 1680 × 1050 1920 × 1200*2 VGA VESA VESA CEA-861 VESA VESA VESA VESA CVT, VESA CVT RB VESA CVT, VESA CVT RB Vertical Scan Frequency Dot Clock 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 60 Hz 193.3 MHz (Max.
●●EV2436W Analog Input (D-Sub) Resolution Applicable Signals 640 × 480 720 × 400 800 × 600 1024 × 768 1280 × 720 1280 × 960 1280 × 1024 1600 × 1200 1680 × 1050 1920 × 1200*1 VGA, VESA VGA TEXT VESA VESA CEA-861 VESA VESA VESA VESA CVT, VESA CVT RB VESA CVT, VESA CVT RB Vertical Scan Frequency Dot Clock ~75 Hz 70 Hz ~75 Hz ~75 Hz 60 Hz 60 Hz ~75 Hz 60 Hz 60 Hz 60 Hz 193.3 MHz (Max.
2-2. Setting the Resolution When you connect the monitor to the PC and find that the resolution is improper, or when you want to change the resolution, follow the procedure below. ●●Windows 8 / Windows 7 1. For Windows 8, click the “Desktop” tile on the Start Screen to display the desktop. 2. Right-click the mouse anywhere on the desktop except for icons. 3. From the displayed menu, click “Screen resolution”. 4. On the “Screen Resolution” dialog box, select the monitor. 5.
2-3. Adjusting Color ●●To select the display mode (FineContrast Mode) This function allows easy selection of a desired mode according to monitor application. Display Modes Mode Purpose User1 Select this to define a desired set of parameter settings. User2 sRGB Suitable for color matching with sRGB compatible peripherals. Paper Produces a printed paper effect. Suitable for displaying images from media such as books and documents. Movie Suitable for playing back animated images.
●●To perform advanced adjustments The “Color” menu of the Setting menu allows you to set and save the independent color adjustment for each mode. Attention • It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more after the monitor power has been turned on, and then adjust the monitor. • Perform the range adjustment first when adjusting color for analog signals (see “To adjust color gradation automatically” (page 28)).
●●To adjust contrast The brightness of the screen is adjusted by varying the video signal level. Adjustable range 0 to 100 Procedure 1. Choose “Color” in the Setting menu, and press . . 2. Choose “Contrast” in the “Color” menu, and press The “Contrast” menu appears. 3. Use or for adjustment. to exit. 4. Press Note • In the contrast of 50, every color gradation is displayed.
●●To adjust gamma Gamma can be adjusted. The brightness of the monitor varies depending on the input signal, however, the variation rate is not proportional to the input signal. To keep the balance between the input signal and the brightness of the monitor is called as “Gamma correction”. Adjustable range 1.8, 2.0, 2.2 Procedure 1. Choose “Color” in the Setting menu, and press . . 2. Choose “Gamma” in the “Color” menu, and press The “Gamma” menu appears. 3. Use or for adjustment. to exit. 4.
●●To adjust hue This function allows you to adjust hue. Adjustable range -50 to 50 Procedure 1. Choose “Color” in the Setting menu, and press . . 2. Choose “Advanced Settings” in the “Color” menu, and press 3. Choose “Hue” in the “Advanced Settings” menu, and press . The “Hue” menu appears. 4. Use or for adjustment. to exit. 5. Press Attention • Using this function may make some color gradations unavailable for display.
●●To adjust gain The brightness of each color component red, green, and blue is called “Gain”. You can change the hue of “white” by adjusting gain. Adjustable range 0 to 100 Procedure 1. Choose “Color” in the Setting menu, and press . . 2. Choose “Advanced Settings” in the “Color” menu, and press 3. Choose “Gain” in the “Advanced Settings” menu, and press . The “Gain” menu appears. 4. Adjust gain with 5. Press or for each of red, green, and blue. to exit.
2-4. Screen Adjustment ●●Digital Signal Input When digital signals are input, images are displayed correctly based on the preset data of the monitor, but if characters and / or lines appear blurred, go to “To modify blurred characters / lines” (page 28). When performing more advanced adjustment, see “2-3. Adjusting Color” (page 19) and subsequent pages. ●●Analog Signal Input Attention • It takes about 30 minutes for the performance of electrical parts to stabilize.
2. Prepare to use analog screen adjustment patterns. Load the “EIZO LCD Utility Disk” to your PC, and then open the “Screen adjustment pattern files”. Note • For details and instructions on opening the “Screen adjustment pattern files”, refer to the Readme.txt file. 3. Perform the auto adjustment again with the analog screen adjustment pattern displayed. ●●To adjust flickering, screen position, and screen size automatically Procedure 1.
●●To remove flickering or blurring Procedure . 1. Choose “Analog Adjustment” in the “Screen” menu, and press 2. Choose “Phase” in the “Analog Adjustment” menu, and press . The “Phase” menu appears. 3. Adjust the phase with 4. Press or to minimize flickering or blurring. to exit. When vertical bars appear on the screen after adjustment, go back to “To eliminate vertical bars ”.
5. Adjusting color gradation. ●●To adjust color gradation automatically Every color gradation (0 to 255) can be displayed by adjusting the signal output level. Procedure 1. Display Pattern 2 in full screen on the monitor using the “Screen adjustment pattern files”. 2. Choose “Screen” in the Setting menu, and press . 3. Choose “Analog Adjustment” in the “Screen” menu, and press . 4. Choose “Auto Range Adjust” in the “Analog Adjustment” menu, and press 5. Select “Yes” with or , and press . .
2-5. Screen Size Changing ●●Screen Size Changing The image with the resolution other than the recommended resolution is displayed in full screen automatically. You can change the screen size by using the “Screen Size” function. Setting Function Full Screen Displays an image in full screen. Images are distorted in some cases because the vertical rate is not equal to the horizontal rate. Enlarged Displays an image in full screen.
●●To adjust brightness of non-display area A border (black area with no image) around the image appears in the “Normal” or “Enlarged” mode. Border Procedure 1. Choose “Monitor Settings” in the Setting menu, and press . 2. Choose “Border Intensity” in the “Monitor Settings” menu, and press The “Border Intensity” menu appears. 3. Use 4. Press 30 or for adjustment. to exit. Chapter 2 Adjusting Screens .
Chapter 3 Setting Monitor 3-1. Adjusting Volume This function allows you to adjust the volume. Adjustable range 0 to 30 Procedure . 1. Press 2. Use or 3. Press for adjustment. to exit. Note • The volume for the speakers and the headphone can be set individually. 3-2. Selecting sound source while using the DisplayPort signal input This function allows you to switch sound source during DisplayPort signal input. You can select the Stereo Mini Jack or DisplayPort. Procedure 1.
3-3. Compensating viewing angle deficiency (EV2316W / EV2416W only) When the screen is to be viewed from below, the viewing angle can be compensated for so the screen looks as if it is being seen from directly ahead. Off -20˚ -40˚ Adjustable range -40˚, -20˚, Off Procedure 1. Choose “Monitor Settings” in the Setting menu, and press . . 2. Choose “Up View” in the “Monitor Settings” menu, and press The “Up View” menu appears. 3. Select “-40˚”, “-20˚”, or “Off” with 4. Press or . to exit.
3-5. Locking Operation Buttons This function allows you to lock the settings to prevent them being changed. Procedure 1. Press to turn off the monitor. while pressing 2. Hold down to turn on the monitor. The Lock / Unlock setting is toggled by performing the operation in step 2. Note • The following operations are available even if the buttons are locked: - Turning on or off the monitor with the Power button 3-6.
3-8. Changing Setting Menu Display Position You can change the display position of the Setting menu. Procedure 1. Choose “Monitor Settings” in the Setting menu, and press . . 2. Choose “Menu Settings” in the “Monitor Settings” menu, and press . 3. Choose “Menu Position” in the “Menu Settings” menu, and press The “Menu Position” menu appears. 4. Choose the position with 5. Press or . to exit. 3-9. Setting Language This function allows you to select a language for the Setting menu or messages.
3-10. Resetting the Monitor to the Default Settings The setting values are reset to the default settings. Attention • After resetting, you cannot undo the operation. Note • Regarding the default setting, see “Main Default Settings” (page 60). ●●To reset the color adjustments This function only resets the color adjustments for the currently selected mode to the default settings. Procedure 1. Choose “Color” in the Setting menu, and press . 2. Choose “Color Reset” in the “Color” menu, and press 3.
Chapter 4 Power Saving Functions 4-1. Setting Power Saving ●●Monitor This function allows you to set the monitor into the power saving mode according to the PC status. When the monitor has shifted to the power saving mode, the images on the screen are not displayed. Attention • Turning off the main power switch or unplugging the power cord completely shuts off power supply to the monitor. • When the monitor is in power saving mode, devices connected to the USB downstream port will still work.
●●Audio Output This monitor allows you to turn off the audio output from the speakers / headphone at the power saving mode. Procedure 1. Choose “Sound” in the Setting menu, and press . 2. Choose “Power Save” in the “Sound” menu, and press . The “Power Save” menu appears. 3. Select “Sound On” or “Sound Off” with or . to exit. 4. Press 4-2. Setting Power Indicator This function allows you to set the power indicator (blue) ON / OFF in the monitor ON condition. Procedure 1.
●●EcoView Optimizer 2 Using the EcoView Optimizer 2 function automatically adjusts the screen brightness according to the white level of the input signal. This function can reduce the power consumption while maintaining the brightness specified by the input signal. Procedure 1. Press . 2. Choose “EcoView Optimizer 2” in the “EcoView Menu” menu, and press . The “EcoView Optimizer 2” menu appears. 3. Select “On” or “Off” with or . to exit. 4.
5. When “On” is selected, select “EcoView Sense Settings” for setting the details. Item Setting Range Description Time 5, 30 sec 1, 3, 5, 10, 15, 30, 45, 60 min Specifies the time from when a person leaves the monitor until the “No Presence detected” message appears. The monitor shifts to the power saving mode about 20 seconds after the message is displayed.
4-5. Checking the power saving level The EcoView menu allows you to check Power Reduction, CO2 Reduction, and Eco Performance Level. The more indicators light up representing the Eco Performance Level, the higher the power saving level attained. Example: EV2436W Indicator Procedure 1. Press . The “EcoView Menu” menu appears. Note • Power reduction: the backlight’s reduction of power consumption as a result of the adjusted brightness value.
Chapter 5 Troubleshooting If a problem still remains after applying the suggested remedies, contact your local EIZO representative. 5-1. No picture Problem 1. No picture • Power indicator does not light. Possible cause and remedy • • • • Check whether the power cord is connected properly. Turn the main power switch on. Press . Turn off the main power, and then turn it on again a few minutes later. • Power indicator is lighting blue.
Problem 2. The message below appears. • The message shows that the input signal is out of the specified frequency range. Example: Possible cause and remedy This message appears when the signal is not input correctly even when the monitor functions properly. • Check whether the PC is configured to meet the resolution and vertical scan frequency requirements of the monitor (see “2-1. Compatible Resolutions” (page 14)). • Reboot the PC. • Select an appropriate setting using the graphics board’s utility.
5-3. Imaging problems (for digital only) Problem Possible cause and remedy 1. The monitor configuration is changed to single under the multiple monitor configuration (when DisplayPort is connected). • When two monitors are connected to one PC using DisplayPort, and the power to one of the monitors is turned off with the power button, the screen setting may be changed to the single monitor configuration. In such a case, enable the “DP HotPlug” function with the following procedures.
5-5. Other problems Problem 44 Possible cause and remedy 1. The Setting menu does not appear. • Check whether the operation lock function is active (see “3-5. Locking Operation Buttons” (page 33)). 2. The “Smoothing” on the Setting menu “Screen” cannot be selected. • You cannot choose “smoothing” when the screen is displayed in the following resolutions or settings.
Problem 6. USB devices connected to the monitor do not work. Possible cause and remedy • Check whether the USB cable is connected correctly (see “6-5. Making Use of USB (Universal Serial Bus)” (page 52)). • Change the USB port to another one. If the PC or peripheral devices works correctly by changing the USB port, contact your local EIZO representative. (Refer to the manual of the PC for details.) • Reboot the PC.
Chapter 6 Reference 6-1. Attaching the Optional Arm An optional arm (or an optional stand) can be attached by removing the stand section. Please refer to our web site for the corresponding optional arm (or optional stand). http://www.eizo.com Attention • When attaching an arm or stand, follow the instructions of their User’s Manual. • When using another manufacturer’s arm or stand, confirm the following in advance and select one conforming to the VESA standard.
6-2. Detaching / Attaching the TriStand2 Stand Base Note • There are 2 types of shapes for the stand brace and the base mounting section (refer to the figures in the procedure). Check the shape of the monitor you have purchased. Detaching procedure The Stand base that was attached during setup can be detached using the following procedures. 1. Lay the LCD monitor on a soft cloth spread over on a stable surface with the panel surface facing down. 2.
Attaching procedure The once removed the Stand base can be attached to the monitor again with the following procedures. 1. Lay the LCD monitor on a soft cloth spread over on a stable surface with the panel surface facing down. 2. Hold the Stand base with the “REAR” side facing upward, align the hole (a) of the Stand base with the tab (b) at the bottom of the monitor, and snap the tab into the hole. b b a a 3. Turn the supplied screw in the “LOCK” direction to lock the Stand base.
6-3. Attaching / Detaching the TriStand2 Cable Holder When you want to use the cable holder with TriStand2, follow the procedure below. The holder can also be removed. Note • FlexStand2 is a set comprised of the stand and the cable holder. Attaching procedure 1. Pass the cables through the cable holder. 2. Shut the bottom of the cable holder. 3. While holding the shut section, insert the cable holder into the Stand base.
Detaching procedure 1. Shut the bottom of the cable holder. 2. While holding the shut section, lift the cable holder upward to remove it from the Stand base.
6-4. Connecting Multiple PCs The product has multiple connections to PCs and allows you to switch to one of the connections for display.
●●To set input signal selection Setting Function Auto The monitor recognizes the connector through which PC signals are input. When a PC is turned off or enters the power saving mode, the monitor automatically displays another signal. Manual The monitor displays the signal from the selected connector despite the signal input. Select the input signal for display using the operation button. Procedure . 1. Choose “Monitor Settings” from the Adjustment menu, and press 2.
●●Connection Procedure (Setup of USB Function) 1. Connect the monitor first to a PC using the signal cable, and run the PC. 2. Connect the USB cable between the USB downstream port of the PC and the USB upstream port of the monitor. The USB hub function is set up automatically upon connection of the USB cable. 3. Connect the peripheral USB devices to the USB downstream port of the monitor. USB downstream port USB upstream port 6-6.
6-7. Specifications ●●EV2316W LCD Panel Size 23.0-inch (580 mm) Type TFT color LCD, LED backlight Surface treatment Anti-Glare Hard Coating Viewing angles Horizontal 170˚, vertical 160˚ (CR≥10) Dot Pitch 0.2655 mm Response Time Black-white-black: Approx.
Mass Movable range Main unit (FlexStand2) Approx. 5.7 kg (12.6 lbs.) Main unit (TriStand2) Approx. 4.3 kg (9.5 lbs.) Main unit (without stand) Approx. 3.1 kg (6.8 lbs.) FlexStand2 TriStand2 Environmental Conditions Temperature Humidity Air Pressure USB Tilt: 30˚ Up, 0˚ Down Swivel: 172˚ Right, 172˚ Left Adjustable height: 195 mm (7.7 inch) (179 mm (7.0 inch) for tilt of 0˚) Rotation: 90˚ (Clockwise) Tilt: 25˚ Up, 0˚ Down Swivel: 172˚ Right, 172˚ Left Adjustable height: 60 mm (2.
Power Consumption Screen Display On 40 W or less Power saving mode 0.3 W or less (with no USB connections, “EcoView Sense”: “Off”, and “Sound” - “Power Save”: “Sound Off”) Power Off 0.3 W or less Main Power Off 0W Input Signal Connector D-Sub mini 15-pin DVI-D connector (Applicable to HDCP) DisplayPort (Standard V1.1a, applicable to HDCP) Applicable Format (Audio signal) - 2ch linear PCM (32 kHz / 44.1 kHz / 48 kHz / 88.
●●EV2416W LCD Panel Size 24.1-inch (610 mm) Type TFT color LCD, LED backlight Surface treatment Anti-Glare Hard Coating Viewing angles Horizontal 170˚, vertical 160˚ (CR≥10) Dot Pitch 0.270 mm Response Time Black-white-black: Approx. 5 ms Horizontal Scan Analog Frequency Digital 31 - 76 kHz DVI 31 - 76 kHz DisplayPort 31 - 76 kHz Vertical Scan Frequency Analog Digital 55 - 61 Hz (non-interlace) DVI 59 - 61 Hz (non-interlace) DisplayPort 59 - 61 Hz (non-interlace) Resolution Max.
Movable range FlexStand2 TriStand2 Environmental Conditions Temperature Humidity Air Pressure USB Tilt: 30˚ Up, 0˚ Down Swivel: 172˚ Right, 172˚ Left Adjustable height: 195 mm (7.7 inch) (158 mm (6.2 inch) for tilt of 0˚) Rotation: 90˚ (Clockwise) Tilt: 25˚ Up, 0˚ Down Swivel: 172˚ Right, 172˚ Left Adjustable height: 60 mm (2.36 inch) Operating: 5˚C to 35˚C (41˚F to 95˚F) Transportation/ Storage: -20˚C to 60˚C (-4˚F to 140˚F) Operating: 20 % to 80 % R.H.
Input Signal Connector D-Sub mini 15-pin DVI-D connector (Applicable to HDCP) DisplayPort (Standard V1.1a, applicable to HDCP) Applicable Format (Audio signal) - 2ch linear PCM (32 kHz / 44.1 kHz / 48 kHz / 88.2 kHz / 96 kHz) Analog Input Signal (Sync) Separate, TTL, positive / negative Analog Input Signal (Video) Analog, Positive (0.7 Vp-p / 75 Ω) Digital Signal (DVI) Transmission System TMDS (Single Link) Audio Output Speaker output: 1.0 W + 1.
●●Main Default Settings Auto EcoView Standard EcoView Optimizer 2 On EcoView Sense Off FineContrast Mode User1 Screen Size Full Screen Smoothing 3 Power Save On Eco Timer Off Language English Menu Position Center Input Signal Manual ●●Outside Dimensions EV2316W / EV2336W FlexStand2 Unit: mm (inch) 209 (8.2) 245.5 (9.7) 360 (14.2) 342 (13.5) 30° 10° 23 (0.91) 268.5 (10.6) 125 (4.9) 28.5 (1.12) 220 (8.7) 100 (3.9) 220 (8.7) 54.5 (2.15) 60.5 (2.38) 73 (2.87) 320 (12.6) 537 (21.
31.5 (1.24) 59.5 (2.34) 209 (8.2) 245.5 (9.7) 20 (0.79) 46 (1.81) 200 (7.9) 129 (5.1) 100 (3.9) 129 (5.1) 360 (14.2) TILT 95 (3.74) TILT 125 (4.9) 245 (9.6) 220 (8.7) 100 (3.9) 220 (8.7) 108.8 (4.3) 100 (3.9) 108.7 (4.3) 73 (2.87) 14.3 (0.56) 130.5 (5.1) 69.5 (2.74) 36 (1.42) 92.5 (3.64) 447.5 (17.6) 387.5 (15.3) 229 (9.0) 60 (2.36) 90 (3.54) 11 (0.43) 25° 288.8 (11.4) 317.5 (12.5) 540 (21.3) 511.8 (20.1) 14.4 (0.57) 70 (2.76) 24.5 (0.96) ° 95 (3.74) 57 (2.24) 172 73 (2.87) 320 (12.
TriStand2 Unit: mm (inch) 16 (0.63) 50 (1.97) 92.5 (3.64) 176 (6.9) 142 (5.6) TILT 11 (0.43) 45 (1.77) 200 (7.9) ●●Accessories Signal cable Cleaning Kit MD-C87 EIZO “ScreenCleaner” For the latest information about the accessories, refer to our web site. http://www.eizo.com 62 Chapter 6 Reference 226.25 (8.9) 100 (3.9) 226.25 (8.9) 129 (5.1)100 (3.9)129 (5.1) 552.5 (21.8) 520.4 (20.5) 70.5 (2.78) 95 (3.74) 17 326 (12.8) 358 (14.1) 16.05 (0.63) 2° SWIVEL 73 (2.87) 2° 468 (18.4) 408 (16.
6-8. Preset Timing The following table shows factory preset analog signal timing. Attention • Display position may be deviated depending on the PC connected, which may require screen adjustment using Setting menu. • If a signal other than those listed in the table is input, adjust the screen using the Setting menu. However, screen display may still be incorrect even after the adjustment.
●●EV2416W Resolution Applicable Signals 640 × 480 800 × 600 1024 × 768 1280 × 720 1280 × 960 1280 × 1024 1600 × 1200 1680 × 1050 1680 × 1050 1920 × 1200 1920 × 1200 VGA VESA VESA CEA-861 VESA VESA VESA VESA CVT VESA CVT RB VESA CVT VESA CVT RB Frequency Dot Clock: MHz 25.18 40.00 65.00 74.25 108.00 108.00 162.00 146.25 119.00 193.25 154.
6-9. Glossary Clock The analog signal input monitor needs to reproduce a clock of the same frequency as the dot clock of the graphics system in use, when the analog signal is converted to a digital signal for image display. This is called clock adjustment. If the clock pulse is not set correctly, some vertical bars appear on the screen. DDC/CI (Display Data Channel / Command Interface) VESA provides the standardization for the interactive communication of the setting information, etc.
Overdrive This technology enhances response speed by increasing the potential difference at the time of motion of liquid-crystal pixels, and it is used for liquid-crystal TV sets and others in general. It provides clear-cut three-dimensional display with little afterimage, by improving response speed of the intermediate graduation range that frequently appears in moving images. Phase Phase means the sampling timing to convert the analog input signal to a digital signal.
Appendix Trademark The DisplayPort Compliance Logo and VESA are registered trademarks of the Video Electronics Standards Association. Windows, Windows Vista, Windows Media, SQL Server, and Xbox 360 are registered trademarks of Microsoft Corporation in the United States and other countries. Apple, Mac, Macintosh, iMac, eMac, Mac OS, MacBook, PowerBook, ColorSync, QuickTime, and iBook are registered trademarks of Apple Inc.
ENERGY STAR As an ENERGY STAR Partner, EIZO Corporation has determined that this product meets the ENERGY STAR guidelines for energy efficiency. TCO This product has acquired the TCO standard that relates to the safety, ergonomics (EcoView Optimizer 2: Off), environment and so forth of office equipment. For an overview of the TCO, refer to our web site. http://www.eizo.
FCC Declaration of Conformity For U.S.A. , Canada, etc. (rated 100-120 Vac) Only FCC Declaration of Conformity We, the Responsible Party EIZOInc. 5710WarlandDrive,Cypress,CA90630 Phone:(562)431-5011 declare that the product Tradename:EIZO Model:FlexScanEV2316W/EV2336W/EV2416W/EV2436W is in conformity with Part 15 of the FCC Rules.
Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor Dieser Monitor ist für Bildschirmarbeitsplätze vorgesehen. Wenn nicht der zum Standardzubehör gehörige Schwenkarm verwendet wird, muss statt dessen ein geeigneter anderer Schwenkarm installiert werden.
LIMITED WARRANTY LIMITED WARRANTY EIZOCorporation(hereinafterreferredtoas“EIZO”)anddistributorsauthorizedbyEIZO(hereinafterreferredtoasthe “Distributors”)warrant,subjecttoandinaccordancewiththetermsofthislimitedwarranty(hereinafterreferredtoasthe “Warranty”),totheoriginalpurchaser(hereinafterreferredtoasthe“Original Purchaser”)whopurchasedtheproduct specifiedinthisdocument(hereinafterreferredtoasthe“Product”)fromEIZOorDistributors,thatEIZOa
BEGRENZTE GARANTIE EIZO Corporation (im Weiteren als „EIZO“ bezeichnet) und die Vertragsimporteure von EIZO (im Weiteren als „Vertrieb(e)“bezeichnet)garantierendemursprünglichenKäufer(imWeiterenals„Erstkäufer“bezeichnet),derdasin diesemDokumentvorgegebeneProdukt(imWeiterenals„Produkt“bezeichnet)vonEIZOodereinemVertrieberworben hat,gemäßdenBedingungendieserbeschränktenGarantie(imWeiterenals„Garantie“bezeichnet),dassEIZOund derVertriebnacheigenemE
GARANTIE LIMITÉE EIZO Corporation (ci-après dénommé « EIZO ») et les distributeurs autorisés par EIZO (ci-après dénommés « Distributeurs »), sous réserve et conformément aux termes de cette garantie limitée (ci-après dénommée « Garantie »), garantissent à l’acheteur initial (ci-après dénommé « Acheteur initial ») du produit spécifié dans la présente (ci-après dénommé « Produit ») acheté auprès d’EIZO ou de Distributeurs agréés EIZO, que EIZO et ses
GARANTÍA LIMITADA EIZO Corporation (en lo sucesivo “EIZO”) y sus distribuidores autorizados (en lo sucesivo los “Distribuidores”), conarregloydeconformidadconlostérminosdeestagarantíalimitada(enlosucesivola“Garantía”),garantizanal compradororiginal(enlosucesivoel“Comprador original”)quecompróelproductoespecificadoenestedocumento(en losucesivoel“Producto”)aEIZOoasusDistribuidores,queEIZOysusDistribuidores,asupropiocriterio,repararán osus
GARANZIA LIMITATA EIZOCorporation(acuisifaràriferimentodaquiinpoicon“EIZO”)ediDistributoriautorizzatidaEIZO(acuisifarà riferimento da qui in poi con “Distributori”) garantiscono, secondo i termini di questa garanzia limitata (a cui si farà riferimentodaquiinpoicon“Garanzia”)all’acquirenteoriginale(acuisifaràriferimentodaquiinpoicon“Acquirente originale”) che ha acquistato il prodotto specificato in questo documento (a cui si farà rif
BEGRÄNSAD GARANTI EIZOCorporation(nedankallat“EIZO”)ochEIZOsauktoriseradedistributörer(nedankallade“Distributörer”)garanterar ienlighetmedvillkorenidennabegränsadegaranti(nedankallad“Garantin”)denursprungligeköparen(nedankallad den“Ursprunglige köparen”)somköptedenidokumentetspecificeradeprodukten(nedankallad“Produkten”)från EIZOellerDistributörer,attEIZOellerDistributörerenligtegetgottfinnandekostnadsfrittantingenrepareraellerbytaut dendefektaPr
ΠΕΡΙΟΡΙΣΜΕΝΗ ΕΓΓΥΗΣΗ Η EIZO Corporation (στο εξής «EIZO») και οι διανομείς που εξουσιοδοτεί η EIZO (στο εξής «Διανομείς») παρέχουν εγγύηση, υποκείμενη και σύμφωνα με τους όρους της παρούσας περιορισμένης εγγύησης (στο εξής «Εγγύηση»),στοναρχικόαγοραστή(στοεξής«Αρχικός Αγοραστής»)οοποίοςαγόρασετοπροϊόνπουκαθορίζεταιστο παρόνέγγραφο(στοεξής«Προϊόν»)απότηνEIZOήτουςΔιανομείς,ηοποίαεξασφαλίζειότιηEIZOκαιοιΔιανομείς, σύμφωναμετηδιακριτήευχέρειάτ
ОГРАНИЧЕННАЯ ГАРАНТИЯ EIZO Corporation (называемая в дальнейшем “EIZO”) и авторизированные EIZO дистрибуторы (называемые в дальнейшем“Дистрибуторы”)гарантируют,всоответствиисусловиямиипунктамиэтойограниченнойгарантии (называемойвдальнейшем“Гарантия”),первичномупокупателю(называемомувдальнейшем“Первоначальный покупатель”),которыйприобрелуEIZOилиДистрибуторовпродукт,указанныйвэтомдокументе(называемый в дальнейшем “Продукт”), что EIZO или Дистрибуторы на св
有限责任保证书 EIZOCorporation(以下简称 EIZO )和 EIZO 授权的经销商(以下简称 经销商 ),接受并依照本有限责任保证书(以 下简称 保证书 )之条款,向从 EIZO 和经销商购买本文中所规定产品(以下简称 产品 )的原买方(以下称 原买方 ) 提供保证 :在保证期内(规定如下),如果原买方发现按本产品所附使用说明书(以下简称 用户手册 )所述方式正常使 用本产品过程中,本产品出现故障或损坏,EIZO 和经销商根据其独自的判断免费修理或更换该产品。 本保证期限定为(i)自本产品购买之日起的五(5)年期间或限定为到达(ii)使用本产品 3 万小时的期限(以下简称 保证期限 )。 EIZO和经销商将不向原买方或任何第三方承担本保证书所规定之外的与本产品有关的任何责任或义务。 本产品的任何部件停产七 (7) 年后,EIZO 和经销商将不再保留或保管任何这类部件。维修显示器时,EIZO 与经销商将使 用符合我方质量控制标准的替换零件。 本保证书仅对于设有经销商的国家或地区有效。本保证书并不限定原买方的任何法律权利。 无论本保证书的任何其他条款如何规定,对于任何下列情况之一,EIZO 和经
Recycling Information Recycling Information This product, when disposed of, is supposed to be collected and recycled according to your country’s legislationtoreduceenvironmentalburden.Whenyoudisposeofthisproduct,pleasecontactadistributoror anaffiliateinyourcountry. ThecontactaddresseesarelistedontheEIZOwebsitebelow. http://www.eizo.com ForrecyclinginformationforcustomersinSwitzerland,pleaserefertothefollowingwebsite. http://www.swico.
Πληροφορίες ανακύκλωσης Τοπροϊόναυτό,όταναπορρίπτεται,πρέπεινασυλλέγεταικαιναανακυκλώνεταισύμφωναμετηνομοθεσία τηςχώραςσαςέτσιώστεναμηνεπιβαρύνειτοπεριβάλλον.Γιανααπορρίψετετοπροϊόν,επικοινωνήστεμε έναναντιπρόσωποήμιαθυγατρικήεταιρείαστηχώρασας. ΟιδιευθύνσειςεπικοινωνίαςαναγράφονταιστηντοποθεσίαwebτηςEIZOπαρακάτω. http://www.eizo.
Informace o recyklaci Při likvidaci produktu musí být produkt vyzvednut a recyklován podle zákonů příslušné země, aby nedocházelo k zatěžování životního prostředí. Zbavujete-li se produktu, kontaktujte distributora nebo pobočkuvesvézemi.KontaktníadresyjsouuvedenynanásledujícíwebovéstráncespolečnostiEIZO. http://www.eizo.com Ringlussevõtu alane teave Keskkonnakoormusevähendamisekstulekskasutatudtootedkokkukogudajavõttaringlussevastavaltteie riigiseadustele.
Информация относно рециклиране Приизхвърлянетонатозипродуктсепредлагасъбиранетоирециклиранетомусъобразнозаконитена вашатастраназадасенамализамърсяванетонаоколнатасреда.Когатоискатедасеосвободитеот тозипродукт,молясвържетесестърговскиямупредставителилисъссъответнитеорганиотговарящи затовавъввашатастрана. ДаннитезавръзкаснассаописанинаследнияИнтернетсайтнаEIZO: http://www.eizo.
China Measures for RoHS Compliance in ChinaRoHS 关于电子信息产品污染控制标识 本标识根据「电子信息产品污染控制管理办法」,适用于在中华人民共和国销售的电子信息产品。标识中央的 数字为环保使用期限的年数。只要您遵守该产品相关的安全及使用注意事项,在自制造日起算的年限内,不会 产生对环境污染或人体及财产的影响。上述标识粘贴在机器背面。 • 有毒有害物质或元素的名称及含量 部件名称 有毒有害物质或元素 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) 印刷电路板 × ○ ○ ○ ○ ○ 机箱 ○ ○ ○ ○ ○ ○ 液晶显示器 × ○ ○ ○ ○ ○ 其他 × ○ ○ ○ ○ ○ ○ :表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 规定的限量要求以下。 × :表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 规定的限量要求。 ( 企业可在此处 , 根据实际情況对上表中打“×” 的技术原因进行进一步说明 ) 84 Appe
8th Edition-August, 2013 Copyright © 2012-2013 EIZO Corporation All rights reserved. 03V24034H1 (U.