Important Please read PRECAUTIONS, this User’s Manual and Setup Manual (separate volume) carefully to familiarize yourself with safe and effective usage. • Please read the Setup Manual (separate volume) • The latest User’s Manual is available for download from our site: http://www.radiforce.
Product specification may vary with sales areas. Confirm the specification in the manual written in language of the region of purchase. • It shall be assured that the final system is in compliance to IEC60601-1-1 requirement. • Power supplied equipment can emit electromagnetic waves, that could influence, limit or result in malfunction of the monitor. Install the equipment in a controlled environment, where such effects are avoided. • This is a monitor intended for use in a medical image system.
Notice for this monitor This product is suited to display medical images of such modalities as MRI and CT. It does not support the display of mammography images for diagnosis. This product has been adjusted specifically for use in the region to which it was originally shipped. If the product is used outside the region, it may not operate as specified in the specifications. This product may not be covered by warranty for uses other than those described in this manual.
Cleaning Attention • Never use any solvents or chemicals, such as thinner, benzene, wax, alcohol, disinfectant, and abrasive cleaner, which may damage the cabinet or LCD panel. NOTE • Optional ScreenCleaner is recommended for cleaning the panel surface. ● LCD Panel • Clean the LCD panel with a soft cloth such as cotton cloth or lens cleaning paper. • Remove persistent stains gently with a cloth dampened with a little water, and then clean the LCD panel again with a dry cloth for better finishing.
CONTENTS Cover . ............................................................ 1 Chapter 3 Setting Monitor................................. 21 Notice for this monitor.............................................. 3 3-1. Enabling/Disabling Mode Selection [Mode Preset]...................................................21 CONTENTS.............................................................. 5 Chapter 1 Introduction........................................ 6 1-1. Features..................................
Chapter 1 Introduction Thank you very much for choosing an EIZO Color Monitor. 1-1. Features • • • • Resolution: 2M pixels (Portrait : 1200 × 1600 dots (H × V)) Applicable to DisplayPort (applicable to 8 bit or 10 bit, not applicable to audio signals) 3 signal input terminals (DVI-I x 2, DisplayPort x 1) CAL Switch function for selecting an optimal calibration mode “2-3.
1-2. Switches and Indicators Adjustment menu Switch 1 2 switch switch switch switch 1. 2. 3. 4. 3 4 5. 6. 7. Indicator status 5 6 7 switch switch Power Indicator Operation status Green The screen is displayed Orange Power saving Off Main Power Switch / Power Switch off 1-3. Utility Disk An “EIZO LCD Utility Disk” (CD-ROM) is supplied with the monitor. The following table shows the disk contents and the overview of the software programs.
1- 4. Basic Operation and Functions Basic operation of Adjustment menu 1 Displaying Adjustment Menu Press . The adjustment menu appears. Menu title Current mode Item Settings Menu 2 3 Adjusting/Setting 1. Choose a menu to adjust/set with , and press . 2. Choose an item to adjust/set with , and press . 3. Adjust/set the selected item with , and press Exiting Press a few times. The adjustment menu finishes. Chapter 1 Introduction .
Functions The following table shows all the Adjustment menu’s adjustment and setting menus. Main Menu Color Item Adjusting/Setting “2-3. Color Adjustment” (page 15) Brightness Contrast Temperature Gamma Advanced Settings Hue Saturation Outline Enhancer Gain 6 Colors “3-7. Restoring the Default Setting” (page 24) Color Reset Screen “2-4. Displaying Lower Resolutions” (page 20) “3-4. Setting Orientation” (page 22) Screen Size Image Rotaion Analog Adjustment Auto Adjustment Range Adjustment “2-2.
Chapter 2 Adjusting Screen 2-1. Setting Screen Resolution Compatible Resolutions/Frequencies For details on compatible resolutions, refer to “Compatible Resolutions/Frequencies” in the Setup Manual. Setting Resolution When you connect the monitor to the PC and find that the resolution is improper, or when you want to change the resolution, follow the procedure below. ● Windows Vista 1. Right-click the mouse anywhere on the desktop except for icons. 2. From the displayed menu, click “Personalize”. 3.
2-2. Displaying Screen Correctly Digital Input When digital signals are input, images are displayed correctly based on the preset data of the monitor. When performing advanced adjustment, see “2-3 Color Adjustment” (page 15) and subsequent pages. Analog Input Attention • Wait 30 minutes or more from monitor power on before starting adjustments. (Allow the monitor to warm up for at least 30 minutes before making adjustments.
2 Prepare the display pattern for the analog display adjustment. Download the “Screen adjustment pattern files” from our site: http://www.radiforce.com NOTE • For details and instructions on opening the “Screen adjustment pattern files”, refer to the “Readme.txt” file. 3 Perform the auto adjustment again with the analog screen adjustment pattern displayed. ● To adjust flickering, screen position, and screen size automatically [Auto Adjustment] Procedure 1.
4 Perform advanced adjustments for the following using the menu of the . Adjust the clock, phase and position, in this order. ● To eliminate vertical bars [Clock] Procedure 1. Choose from the menu, and press 2. Adjust the clock with or . Press 3. Press . slowly so as not to miss the adjustment point. to exit the adjustment.
5 Adjust the color gradation. ● To adjust color gradation automatically [Range Adjustment] Every color gradation (0 to 255) can be displayed by adjusting the signal output level. Procedure 1. Display Pattern 2 in full screen on the monitor using the screen adjustment pattern files. 2. Choose from the menu, and press . The color gradation is adjusted automatically. When the auto adjustment is completed, a message appears.
2-3. Color Adjustment ● To select the display mode (CAL Switch) CAL Switch allows you to select easily the adequate mode suitable for the monitor’s application. CAL Switch mode Mode 1-DICOM 2-Custom 3-CAL 4-Text Purpose Available to display in DICOM mode. Available for the color settings according to your preference. Displays the screen adjusted by calibration software. Suitable for displaying texts for word processing or spreadsheets. The mode menu appears. Procedure 1. Press .
● Adjustment items in each mode According to the mode selected, the adjustable function differs. (You can not select any function unavailable for adjustment or setting.) The adjustments or settings made for each mode are applied to all input signals. For the adjustment method of each function, refer to subsequent pages.
● To adjust the brightness [Brightness] The screen brightness is adjusted by changing the brightness of the backlight (Light source from the LCD back panel). Adjustable range: 0 to 100% Procedure 1. 2. 3. 4. Choose from the Adjustment menu, and press . Choose from the menu, and press . Adjust the brightness with or . Press to exit the adjustment. NOTE • You can also adjust the brightness using and .
● To adjust the gamma value [Gamma] The gamma value can be adjusted. The luminance of the monitor varies depending on the input signal, however, the variation rate is not proportional to the input signal. To keep the balance between the input signal and the luminance of the monitor is called as “Gamma correction”. Adjustable range: 1.8-2.6 Procedure 1. 2. 3. 4. Choose from the Adjustment menu, and press Choose from the menu, and press Adjust the gamma value with or .
● To enhance the outline of the image [Outline Enhancer] OutlineEnhancer functions to emphasize outline of the images by emphasizing the color difference between pixels composing the images. This may improve the texture of the material and its feel of the images. On the contrary, it also functions to reproduce the images smoothly by gradating its outline. Procedure 1. 2. 3. 4. 5. Choose from the Adjustment menu, and press . Choose from the menu, and press .
2-4. Displaying Lower Resolutions ● To change screen size [Screen Size] You can change the screen size by using from menu. Menu Full Enlarged Normal (default setting) Function Displays an image in full screen. Images are distorted in some cases because the vertical rate is not equal to the horizontal rate. Displays an image in full screen. In some cases, a blank horizontal or vertical border appears to equalize the vertical rate and the horizontal rate.
Chapter 3 Setting Monitor 3-1. Enabling/Disabling Mode Selection [Mode Preset] Allows you to select the specified modes only. Use this function when all the display modes are not available or when keeping the display mode unchanged. Procedure 1. 2. 3. 4. 5. Choose from the Adjustment menu, and press . Choose from the menu, and press . Select the mode to change its settings with or , and press Select “On” or “Off” with or . Press to exit the adjustment. .
3-3. Setting the EIZO Logo Display [Logo] This function allows you to display, or not, the EIZO logo. Procedure 1. Press to turn off the monitor. 2. Press holding down at least 2 seconds to turn on the monitor. The Optional Settings menu appears. 3. 4. 5. 6. Choose from the menu, and press Select “On” or “Off” with or , and press . Select “Finish” with or . Press to exit the Optional Settings. . The Optional Settings menu is closed. 3-4.
3-5. Setting Language [Language] This function allows you to select a language for the adjustment menu or displaying message. Selectable languages English/German/French/Spanish/Italian/Swedish/Japanese /Simplified Chinese/Traditional Chinese Procedure 1. 2. 3. 4. Choose
3-7. Restoring the Default Setting There are two types of Reset. One is to reset the color adjustment only to the default settings, and the other is to reset all the settings to the default settings. Attention • After resetting, you cannot undo the operation. NOTE • For main default settings, refer to “Main default settings (factory settings)” on page 35.
Chapter 4 Power Saving Function 4-1. Setting the Power Saving [Power Save] This function allows you to set the monitor into the power saving mode according to the PC status. When the monitor enters the power saving mode, no image is displayed on the screen. Attention • Turning off the main power switch or unplugging the power cord completely shuts off power supply to the monitor.
Chapter 5 Troubleshooting If a problem still remains after applying the suggested remedies, contact your local dealer. • • • • 1. No-picture problems → See No.1 - No.2. Imaging problems (digital input) → See No.3 - No.8. Imaging problems (analog input) → See No.3 - No.12. Other problems → See No.13 - No.16. Problems No picture • Power indicator does not light. • Power indicator lights green. • Power indicator lights orange. 2. The message below appears. • This message appears when no signal is input.
5. 6. Problems Afterimages appear 8. Green/red/blue/white dots or defective dots remain on the screen. Interference patterns or pressure marks remain on the screen. Noise appears on the screen. 9. Display position is incorrect. 7. Possible cause and remedy • Afterimages are particular to LCD monitors. Avoid displaying the same image for a long time. • Use the screen saver or power save function to avoid displaying the same image for extended periods of time.
Problems 16. The monitor connected with the USB cable is not detected. / USB devices connected to the monitor does not work. • • • • • • 28 Chapter 5 Troubleshooting Possible cause and remedy Check whether the USB cable is connected correctly. (page 32) Change the USB port to another one. If the PC or peripheral devices works correctly by changing the USB port, contact your local dealer. (Refer to the manual of the PC for details.) Reboot the PC.
Chapter 6 Reference 6-1. Attaching an Arm The stand can be removed and replaced with an arm (or another stand) to be attached to the monitor. Use an arm or stand of EIZO option. Attention • When attaching an arm or stand, follow the instructions of their user’s manual. • When using another manufacturer’s arm or stand, confirm the following in advance and select one conforming to the VESA standard. - Clearance between the screw holes: 100 mm × 100 mm - Thickness of plate: 2.
6-2. Connecting More than Two PCs to the Monitor More than two PCs can be connected to the monitor through the DVI-I and the DisplayPort connector on the back of the monitor.
● To set input signal selection [Input Selection] The monitor recognizes the connector through which PC signals are input. Priority setting Auto Function When a PC is turned off or enters the powersaving mode, the monitor automatically displays another signal. Manual The monitor detects only the PC’s signals currently displaying automatically. Select an active input signal with . Procedure 1. Choose from the Adjustment menu, and press . 2.
6-3. Making Use of USB (Universal Serial Bus) This monitor has a hub compatible with USB. Connected to a PC compatible with USB or another USB hub, this monitor functions as a USB hub allowing connection to peripheral USB devices. ● Required System Environment 1. A PC equipped with a USB port or another USB hub connected to a USB compatible PC 2. Windows 2000/XP/Vista or Mac OS 9.2.2 and Mac OS X 10.2 or later 3.
6-4. Displaying Monitor Information ● Displaying signal information [Signal Info] This function displays the information about the current input signals displayed. 1. Choose from the Adjustment menu, and press . 2. Choose from the menu, and press . The Signal Info screen appears. (Example) ● Displaying monitor information [Monitor Info] This function displays the information about the monitor. 1. Choose from the Adjustment menu, and press . 2.
6-5. Specifications LCD Panel Size 21.3-inch (540 mm) TFT color LCD Surface treatment Anti-Glare Surface hardness 2H Viewing angle Viewing angle : Horizontal 170°, Vertical 170° (CR:10 or more) Dot Pitch 0.270 mm Response Time Approx. 17 ms Horizontal Scan Analog Frequency Digital 31-100 kHz Vertical Scan Frequency Analog 49-86 Hz(1600 × 1200: 49-60 Hz) Digital 59-61 Hz (VGA TEXT: 69-71 Hz) 31-100 kHz Resolution 2M pixels (Portrait: 1200 × 1600 dots (H × V)) Max.
Environmental Conditions USB Temperature Operating temperature: 0 °C - 35 °C (32 °F - 95 °F) Storage temperature: -20 °C - 60 °C (-4 °F - 140 °F) Humidity Operating humidity: 20% - 80% R.H. (no condensation) Storage humidity: 10% - 80% R.H. (no condensation) Pressure Operating: 700 to 1,060 hPa Storage: 200 to 1,060 hPa Standard USB Specification Revision 2.0 Port Upstream port × 1, Downstream port × 2 Communication Speed 480 Mbps (high), 12 Mbps (full), 1.
Outside Dimensions Unit: mm (inch) 35° 35° SWIVEL 240 (9.04) 325 (12.08) TILT 376 (14.08) 326 (12.08) 25 (0.98) 62.5 (2.46) 138 (5.04) 100 (3.09) 138 (5.04) 100 (3.09) 82 (3.23) 325 (12.08) 208.5 (8.02) 15 (0.59) 22.5 (0.89) 140 (5.05) 222.5 (8.08) 272.5 (10.07) 500 (19.07) 434 (17.01) PIV OT 90° 200 (7.09) 33 (1.30) 25 (0.98) 40° 95 (3.74) 323 (12.07) Connector Pin Assignment • DVI-I connector 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Pin No.
• DisplayPort connector 19 17 15 13 11 9 7 5 3 1 20 18 16 14 12 10 8 6 4 2 Pin No. Signal Pin No. Signal Pin No. Signal 1 ML Lane3- 8 Ground 15 AUX CH+ 2 Ground 9 ML Lane1+ 16 Ground 3 ML Lane3+ 10 ML Lane0- 17 AUX CH- 4 ML Lane2- 11 Ground 18 Hot Plug Detect 5 Ground 12 ML Lane0+ 19 Return 6 ML Lane2+ 13 CONFIG1 20 DP PWR 7 ML Lane1- 14 CONFIG2 • USB port Upstream Downstream Series B connector Series A connector Contact No.
6-6. Glossary Clock The analog input monitor needs to reproduce a clock of the same frequency as the dot clock of the graphics system in use, when the analog input signal is converted to a digital signal for image display. This is called clock adjustment. If the clock pulse is not set correctly, some vertical bars appear on the screen.
HDCP (High-bandwidth Digital Contents Protection) Digital signal coding system developed to copy-protect the digital contents, such as video, music, etc. This helps to transmit the digital contents safely by coding the digital contents sent via DVI terminal on the output side and decoding them on the input side. Any digital contents cannot be reproduced if both of the equipments on the output and input sides are not applicable to HDCP system.
6-7. Preset Timing The following table shows factory preset video timing (for analog signal only). Attention • Display position may be deviated depending on the PC connected, which may require screen adjustment using Adjustment menu. • If a signal other than those listed in the table is input, adjust the screen using the Adjustment menu. However, screen display may still be incorrect even after the adjustment.
For U.S.A. , Canada, etc. (rated 100-120 Vac) Only FCC Declaration of Conformity We, the Responsible Party EIZO NANAO TECHNOLOGIES INC. 5710 Warland Drive, Cypress, CA 90630 Phone: (562) 431-5011 declare that the product Trade name: EIZO Model: RadiForce RX220 is in conformity with Part 15 of the FCC Rules.
EMC Information Essential performance of RadiForce series is to display images and operate functions normally. CAUTION The RadiForce series requires special precautions regarding EMC and need to be installed, put into service and used according to the following information. Do not use any cables other than the cables that provided or specified by us. Using other cables may cause the increase of emission or decrease of immunity.
Guidance and manufacturer’s declaration - electromagnetic immunity The RadiForce series is intended for use in the electromagnetic environment specified below. The customer or the user of the RadiForce series should assure that it is used in such an environment. Immunity test IEC/EN60601 test level Compliance level Electromagnetic environment - guidance Conducted RF IEC/EN61000-4-6 3Vrms 150kHz to 80MHz 3Vrms Radiated RF IEC/EN61000-4-3 3V/m 80MHz to 2.
Recommended separation distances between portable and mobile RF communications equipment and the RadiForce Series The RadiForce series is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled.
关于电子信息产品污染控制标识 本标识根据「电子信息产品污染控制管理办法」，适用于在中华人民共和国销售的电子信息产品。标识中央的 数字为环保使用期限的年数。只要您遵守该产品相关的安全及使用注意事项，在自制造日起算的年限内，不会 产生对环境污染或人体及财产的影响。上述标识粘贴在机器背面。 • 有毒有害物质或元素的名称及含量 部件名称 有毒有害物质或元素 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 （Pb） （Hg） （Cd） （Cr（VI）） （PBB） （PBDE） 印刷电路板 × ○ ○ ○ ○ ○ 机箱 ○ ○ ○ ○ ○ ○ 液晶显示器 × × ○ ○ ○ ○ 其他 × ○ ○ ○ ○ ○ ○： 表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 规定的限量要求以下。 ×： 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 规定的限量要求。 ( 企业可在此处 , 根据实际情況对上表中打“×” 的技术原因进行进一步说明 )
