Specifications

Ǧ CRAFTSMAN CAP/BASE
NON-TA P E R E D CAP AND BASE STYLES
The cap and base sets for non-tapered Craftsman Series columns consist of a mitered wrap or a molding. The optional neck trim
is also a molding, applied by the installer. These wraps and/or moldings do not have the E-Z Lock joint, due to the routed edges
of the parts.
In addition to the standard cap and base profile, optional Mission, Tuscan and Prairie styles are available. These styles allow cus-
tomers more freedom of choice when designing their columns, and may be mixed and matched as desired. Custom options may
be possible as well, based on customer requirements.
For columns of non-standard size, the widths of the cap and base will adjusted accordingly. The heights however will remain the
same. Since the non-tapered cap and base install around the shaft, the inside size of the cap will be the same as the outside net
width of the column. When considering the space requirements to wrap the load support, the inside width of the column shaft is
the specification which would be applicable.
Standard Tuscan PrairieMission
Optional "Add-On" Neck Moulding
AA
AA A A
A
B
C
D
E
F
7 1/4" 7 1/4"
9 1/4" 9 1/4"
3 1/4"
3 1/4"
1 1/8"
Non-tapered Cap and Base Specifications
Column
Nominal
Width
Standard
Cap & Base
Width (A)
Mission
Cap & Base
Width (A)
Tuscan Cap and Base
Prairie Cap
& Base
Width (A)
Base Cap
Plinth
Width (A)
Plinth
Height (B)
Torus
Height (C)
Base Height
(B-C)
Echinus
Height (D)
Abacus
Height (E)
Cap Height
(E-F)
Abacus
Width (F)
6” 6 7/8” 7 5/8” 8” 1 1/2” 1 3/4” 3 1/4” 1” 1 1/16” 2 1/16” 8 7/16” 8 1/8”
8” 8 7/8” 9 5/8” 11 3/8” 1 7/8” 2 3/8” 4 1/4” 1 3/4” 1 3/8” 2 11/16” 11 1/4” 10 1/8”
10” 10 7/8” 11 5/8” 13 1/2” 2 3/8” 2 7/8” 5 1/4” 1 13/16” 1 3/4” 3 9/16” 13 1/4” 12 1/8”
12” 12 7/8” 13 5/8” 17” 2 3/4” 3 1/4” 6” 1 7/8” 2” 3 7/8” 17 1/4” 14 1/8”
14” 14 7/8” 15 5/8” 18 5/8” 3 3/8” 4” 7 3/8” 2 5/8” 2 3/8” 5” 19” 16 1/8”
16” 16 7/8” 17 5/8” 20 5/8” 3 3/8” 4” 7 3/8” 2 5/8” 2 3/8” 5” 21” 18 1/8”
18” 18 7/8” 19 5/8” 22 5/8” 3 3/8” 4” 7 3/8” 2 5/8” 2 3/8” 5” 23” 20 1/8”
20” 20 7/8” 21 5/8” 24 5/8” 3 3/8” 4” 7 3/8” 2 5/8” 2 3/8” 5” 25” 22 1/8”
22” 22 7/8” 23 5/8” 26 5/8” 3 3/8” 4” 7 3/8” 2 5/8” 2 3/8” 5” 27” 24 1/8”
24” 24 7/8” 25 5/8” 28 5/8” 3 3/8” 4” 7 3/8” 2 5/8” 2 3/8” 5” 29” 26 1/8”
* Since the cap/base wrap the column, we manufacture them based on inside widths. Due to fit tolerances and material thickness variances, net widths
may be up to
1/8” larger than shown.