ELAD FDM-S2 USER MANUAL www.eladit.
ELAD FDM-S2 User Manual Rev 1.05 10/2014 1 Index 2 3 FDM-S2 Overview ................................................................................................................................. 3 2.1 Sampler Exploit ............................................................................................................................. 3 2.2 Front Panel Description ................................................................................................................ 3 2.
ELAD FDM-S2 User Manual Rev 1.05 10/2014 2 FDM-S2 Overview 2.1 Sampler Exploit FDM-S2 is the second born device in our ELAD SDR SAMPLER line. This product line is developed to give the user the possibility to exploit and study the capability of Sampling technique. With 122.88MHz sampling frequency FDM-S2 can offer the possibility to be a good HF and 6m receiver, but also allow to receive FM Band and part of VHF Band simply adding appropriate pre-selection filters in the front-end of ADC.
ELAD FDM-S2 User Manual Rev 1.05 10/2014 2.3 Rear Panel Description USB 2.0 Connector Connection with the PC. Please use the supplied cable. On/Off Switch Turn On/Off the FDM-S2 HF Antenna Input SMA 50Ω input connector for HF band +20dBm max VHF Antenna Input SMA 50Ω input connector for VHF band +20dBm max External Hardware Connector DB9 connector for external hardware (eg pre-selector filters board). This is NOT a serial port. © 2014 ELAD S.r.l. All rights reserved.
ELAD FDM-S2 User Manual Rev 1.05 10/2014 3 Software & Driver Installation 3.1 Software installation in Windows 8 Windows 7 and Windows XP 3.1.1 First-time install in Windows 8 and Windows 7 Double-click the file “setup.exe” in the CD . The windows installer first installs the prerequisites: Microsoft VC++ 2010 Runtime libraries Microsoft .NET Framework 4.0 (Only for Windows 7) and then the FDM-SW2 software. Click on “Accept” (Only for Windows 7) Click on “Install” © 2014 ELAD S.r.l.
ELAD FDM-S2 User Manual Rev 1.05 10/2014 Click on “Yes” Click on Install Microsoft Visual C++ 2010 x86 Redistributable installation is complete, click on “Finish” © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l.
ELAD FDM-S2 User Manual Rev 1.05 10/2014 Click on “Yes” to start the installation of the .Net Framework 4.0 (Only for Windows 7) Click to “Next” to start the FDM-SW2 software installation © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l.
ELAD FDM-S2 User Manual Rev 1.05 10/2014 Chose the installation folder, then click on “Next” Click on “Next” © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l.
ELAD FDM-S2 User Manual Rev 1.05 10/2014 Click on “Yes” 3.1.2 First-time install in Windows XP Double-click the file “setup.exe” in the installation folder. © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l.
ELAD FDM-S2 User Manual Rev 1.05 10/2014 Click on “Accept” Click on “Install” © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l.
ELAD FDM-S2 User Manual Rev 1.05 10/2014 Click on “Install” Click on Next to install the FDM-SW2 software © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l.
ELAD FDM-S2 User Manual Rev 1.05 10/2014 Select the installation folder, then click on “Next” Click on “Next” © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l.
ELAD FDM-S2 User Manual Rev 1.05 10/2014 The FDM-SW2 Software installation is completed © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l.
ELAD FDM-S2 3.1.3 User Manual Rev 1.05 10/2014 Update an existing software version Double click on file ELAD_FDM_SW2_V_x.xx.msi included in the update and follow the instructions. © 2014 ELAD S.r.l. All rights reserved. No part of this document may be reproduced, published, used, disclosed or disseminated in any form or by any means, electronic, photocopying or otherwise, without prior written permission of ELAD S.r.l.
ELAD FDM-S2 User Manual Rev 1.05 10/2014 3.2 FDM-S2 USB driver 3.2.1 3.2.1.1 FDM-S2 USB driver installation in Windows 8 and Windows 7 First driver installation To install ELAD FDM-S2 driver, connect FDM-S2 sampler to a USB 2.0 socket on PC to power on the device. When Windows detects the new hardware, follow the steps listed below to install driver correctly: Open Control Panel from Start menu, select “System” and “Device Manager”.
ELAD FDM-S2 User Manual Rev 1.05 10/2014 When Windows starts the installation procedure, select the option “Browse my computer for driver software” (the second option). In the next dialog-box, insert the driver folder location using “Browse” button and check the option “Include subfolders”. In this way manual driver search is enabled.
ELAD FDM-S2 User Manual Rev 1.05 10/2014 Click Install. Let the hardware installation automatically completes and, at the procedure ending, click on “Close”; then disconnect and connect FDM-S2 device on the same USB socket. Now ELAD FDM-S2 driver is installed on your PC. © 2014 ELAD S.r.l. All rights reserved.
ELAD FDM-S2 3.2.2 3.2.2.1 User Manual Rev 1.05 10/2014 FDM-S2 USB driver installation in Windows XP First driver installation To install ELAD FDM-S2 driver, connect FDM-S2 sampler to a USB 2.0 socket on PC to power on the device. Windows XP detects the new hardware and starts the hardware installation wizard. Then, next steps to install FDM-S2 driver are listed below: At the first dialog box, select the last option “No, not this time” and “Next”.
ELAD FDM-S2 User Manual Rev 1.05 10/2014 In the next dialog-box, check the options “Search for the best driver in these location” and “Include this location in the search” to enable manual driver search. Clicking on “Browse”, select the path where the driver folder is located: Local Drive (C:) \Programs\ELAD\ELAD FDM-SW2\ELAD_FDM_Driver. Then click “Next”. Let the hardware installation automatically completes and click on “Finish”; then disconnect and connect FDM-S2 device on the same USB socket.
ELAD FDM-S2 3.2.2.1 User Manual Rev 1.05 10/2014 Driver installation verify in Windows 8 and Windows 7 To verify FDM-S2 driver current version, connect the device to USB socket (where the device driver is already installed) and open Control Panel from Start menu. Click on “System” and select “Device Manager”. Expanding “ELAD Samplers” node, FDM-S2 device driver is installed as “ELAD FDM-S2-25”: right click on “ELAD FDM-S2-25” and select “Properties”.
ELAD FDM-S2 3.2.2.2 User Manual Rev 1.05 10/2014 Manual driver update To update FDM-S2 driver, connect the device to USB socket (where the device driver is already installed) and open Control Panel from Start menu. Click on “System” and select “Device Manager”. Under “ELAD samplers” list, the driver for FDM-S2 is installed as “ELAD FDM-S2-25”. Select “ELAD FDMS2-25”, right click on it and execute “Update driver”.
ELAD FDM-S2 User Manual Rev 1.05 10/2014 In the next dialog-box, disable the option “Include subfolders” and choose “Let me pick from a list of device drivers on my computer”. Don’t click “Next”. Verify that “Show compatible hardware” option is checked and ELAD FDM-S2 is selected: then click on “Have a Disk”. In this way the manual driver update is enabled. Don’t click “Next”. © 2014 ELAD S.r.l. All rights reserved.
ELAD FDM-S2 User Manual Rev 1.05 10/2014 Click on “Browse” and search for FDM-S2 driver update folder location; then open winusb_fdmsampler.inf file. Click “OK” and then “Next”. Let the hardware installation automatically completes and, at the procedure ending, click on “Close”; then disconnect and connect FDM-S2 device on the same USB socket. To verify that a correct update is done, enter “Device Manager” in Control Panel; under “ELAD samplers” label select ELAD FDM-S2 driver (see sub-chapter “2.2.1.
ELAD FDM-S2 3.2.2.3 User Manual Rev 1.05 10/2014 Driver installation verify in Windows Xp To verify FDM-S2 driver current version, connect the device to USB socket (where the device driver is already installed) and open Control Panel from Start menu. Click on “System” and select “Device Manager” under “Hardware” label. Expanding “ELAD Samplers” node, FDM-S2 device driver is installed as “ELAD FDM-S2-25”: right click on “ELAD FDM-S2-25” and select “Properties”.
ELAD FDM-S2 3.2.2.4 User Manual Rev 1.05 10/2014 Manual driver update in Windows Xp To update FDM-S2 driver, connect the device to USB socket (where the device driver is already installed) and open Control Panel from Start menu. Click on “System” and select “Device Manager” under “Hardware” label. Select “ELAD FDM-S2” from “ELAD Samplers” list, right click on it and execute “Update driver ” Now Windows XP launches the hardware update wizard: select the last option “No, not this time” and “Next”.
ELAD FDM-S2 User Manual Rev 1.05 10/2014 At next step select “Install from a list or specific location (Advanced)” and “Next”. Then, disable all check-boxes that the system automatically sets and choose the last option for manual driver update, as depicted in figure. Select “Next”. © 2014 ELAD S.r.l. All rights reserved.
ELAD FDM-S2 User Manual Rev 1.05 10/2014 Verify that “Show compatible hardware” option is checked and ELAD FDM-S2 is selected: then click on “Have a Disk”. Don’t click “Next”. Click on “Browse” and search for the FDM-S2 driver update folder location; then open winusb_fdmsampler.inf file, as depicted in figure. Click “OK” and then “Next”. © 2014 ELAD S.r.l. All rights reserved.
ELAD FDM-S2 User Manual Rev 1.05 10/2014 Now driver update starts: at next dialog box select “Continue Anyway” and ignore the warning. Let the hardware update automatically completes and, at the procedure ending, click on “Finish”; then disconnect e connect FDM-S2 device on the same USB socket. To verify that a correct update is done, enter “Device Manager” from Control Panel; under “Universal Serial Bus controllers” list, select ELAD FDM-S2 driver (see chapter “2.2.2.
ELAD FDM-S2 User Manual Rev 1.05 10/2014 Annex A FDM-S2 External Hardware Connector Pin 1: SFE Latch 595 Pin 2: I2C SCL Pin 3: SFE CLOCK 595 Pin 4: I2C SDA Pin 5: Ground Pin 6: Mute Pin 7: Reserved Pin 8: SFE Data 595 Pin 9: Vcc (4.5V) To mute the FDM-S2, connect the Pin 6 to ground. Note: the maximum cable length should not exceed 100 mm. © 2014 ELAD S.r.l. All rights reserved.
ELAD FDM-S2 User Manual Rev 1.05 10/2014 FDM-S2 Technical Specifications ELAD FDM-S2 TECHNICAL SPECIFICATIONS GENERAL Frequency Coverage HF+50MHz Band (10 kHz ÷ 54 MHz): Direct Sampling Mode VHF1 Band (74-108MHz): Undersampling Mode VHF2 Band (135-148MHz): Undersampling Mode Bypass for experimenting use Antenna Connectors HF+50MHz Band input: SMA (50 Ω) SMA/BNC adapter included VHF1 & VHF1 Bands input: SMA (50 Ω) SMA/BNC adapter included Temperature Range 0 ÷ 40 °C PC Interface High-Speed USB 2.
ELAD FDM-S2 User Manual Rev 1.05 10/2014 Declaration of Conformity (EC) The product marked as FDM-S2 manufactured by Manufacturer: ELAD S.r.l.
ELAD FDM-S2 User Manual Rev 1.05 10/2014 Declaration of Conformity (FCC) The product marked as FDM-S2 manufactured by Manufacturer: ELAD S.r.l.
