SEMI-FLUSH MODEL #83227 Français p. 9 ATTACH YOUR RECEIPT HERE Serial Number Purchase Date Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-855-226-7169, 8 a.m. - 4 p.m., EST, Monday - Friday.
PACKAGE CONTENTS E F J I A PART A B C D E F G H I J B C G H D Note: The hanging balls are located in the bottom compartment of the styrofoam container.
HARDWARE CONTENTS AA BB CC Qty: 3 EE Ground Screw Qty: 1 GND Wire Connectors DD Short Machine Long Screws Machine Qty: 2 Screws Qty: 2 FF Threaded Knobs Qty: 2 Mounting Bracket Qty: 1 SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product. • • • • • WARNING IMPORTANT: NEVER attempt any work without shutting off the electricity. Go to the main fuse box, or circuit breaker, in your home.
ASSEMBLY INSTRUCTIONS 1. Insert long machine screws (CC) into the mounting bracket (DD) before connecting to the outlet box. The two long machine screws (CC) should protrude through mounting bracket (DD) for securing canopy (A) in later steps. Connect the mounting bracket (DD) to outlet box with short machine screws (BB). Orient the mounting bracket (DD) so the raised center portion protrudes into the outlet box.
ASSEMBLY INSTRUCTIONS 3. Hang shade from mounting surface. Shade wire tabs will rest inside the lip of the mounting surface. 3 Shade Mounting Surface 4. Secure canopy (E) to mounting bracket (DD) with threaded knobs (FF). 4 DD Hardware Used FF Threaded Knob E x2 FF 5. Insert 40-watt G9 Bulb (G) into threaded socket (J). Screw bulb cover (H) over 40-watt G9 bulb (G) and onto threaded socket (F).
ASSEMBLY INSTRUCTIONS 6. To attach hanging balls pass hanging clip (I) through the wire loop (F). 6 Note: Hanging balls will be marked with a letter. Attach the lettered hanging ball to the corresponding letter found on the mounting surface.
CARE AND MAINTENANCE • Always be certain that electric current is turned off before cleaning this item. • Use a soft, moist cloth with mild non-abrasive soap to clean fixture. Never use glass cleaner on fixture, as it will damage the metal finish. • All glass shades may be washed in a towel-lined sink with warm water and mild soap. Do not wash shades in an automatic dishwasher. TROUBLESHOOTING PROBLEM Fixture does not light. POSSIBLE CAUSE CORRECTIVE ACTION 1. Fixture may be wired incorrectly. 1.
REPLACEMENT PARTS LIST For replacement parts, call our customer service department at 1-855-226-7169, 8 a.m. - 4 p.m., EST, Monday - Friday. PART A B C D H AA BB CC DD FF DESCRIPTION 13 Inch Hanging Ball 9 Inch Hanging Ball 8 Inch Hanging Ball 10 Inch Hanging Ball Bulb Cover Wire Connector Short Machine Screw Long Machine Screw Mounting Bracket Threaded Knob B A AA BB C PART # 13IHB83227 9IHB83227 8IHB83227 10IHB83227 BC001 WC001 SCR832X050 SCR832X100 XBAR83227 TK83227 D CC H DD FF GND Rev.
LUMINAIRE SEMI-ENCASTRÉ MODÈLE #83227 JOIGNEZ VOTRE REÇU ICI Numéro de série Date d’achat Des questions, des problèmes, des pièces manquantes? Avant de retourner l’article au détaillant, appelez notre service à la clientèle au 1 855 226-7169, entre 8 h et 16 h (HNE), du lundi au vendredi.
CONTENU DE L’EMBALLAGE E F J I A PIÈCE A B C D E F G H I J B C D G H Renarque : Les boules suspendues sont situées dans le compartiment inférieur d’emballage en polystyrène.
QUINCAILLERIE INCLUSE AA BB DD GND Capuchon de connexion Vis à Qté : 3 métaux courtes Qté : 2 CC Vis à métaux longues Qté : 2 EE Vis de mise à la terre Qté : 1 Support de fixation Qté : 1 FF Boutons filetés Qté : 2 CONSIGNES DE SÉCURITÉ Veuillez vous assurer de lire et de comprendre l’intégralité du présent guide avant d’assembler, d’utiliser ou d’installer ce produit. • • • • • AVERTISSEMENT IMPORTANT : NE tentez JAMAIS de travailler sans couper l'électricité.
INSTRUCTIONS POUR L'ASSEMBLAGE 1. Insérez les vis à métaux longues (CC) dans le support de fixation (DD) avant de le fixer sur la boîte de sortie. Les deux vis à métaux longues (CC) doivent dépasser du support de fixation (DD) afin de fixer le pavillon (A) ultérieurement. Fixez le support de fixation (DD) sur la boîte de sortie à l'aide des vis à métaux courtes (BB). Orientez le support de fixation (DD) de façon à ce que la partie centrale surélevée fasse saillie dans la boîte de sortie.
INSTRUCTIONS POUR L'ASSEMBLAGE 3. Suspendez l’abat-jour à la surface de montage. Les languettes en fil de l’abat-jour reposeront à l’intérieur du rebord de la surface de montage. 3 Abat-jour Surface de montage 4. Fixez le pavillon (E) sur le support de fixation (DD) à l'aide des boutons filetés (FF). 4 DD Quincaillerie utilisée FF Boutons filetés E x2 FF 5. Insérez une ampoule G9 de 40 watts (G) dans la douille filetée (J).
INSTRUCTIONS POUR L'ASSEMBLAGE 6. Pour attacher les boules suspendues, enfilez l'attache de suspension (I) à travers la boucle de fil (F). 6 Remarque - Les boules suspendues seront marquées d'une lettre. Attachez chaque boule suspendue marquée d'une lettre sur la lettre correspondante située sur la surface de montage.
ENTRETIEN • Vérifiez toujours que le courant est coupé avant de nettoyer le luminaire. • Utilisez un linge doux et humide ainsi qu’un savon non abrasif. N’utilisez jamais de nettoyants pour vitres; vous risqueriez d’endommager le fini métallique du luminaire. • Les abat-jour en verre peuvent être nettoyés dans un évier couvert de serviettes, à l’aide d’eau tiède et de savon doux. Ne nettoyez pas les abat-jour dans un lave-vaisselle. DÉPANNAGE PROBLÈME Le luminaire ne s’allume pas.
LISTE DES PIÈCES DE RECHANGE Pour obtenir des pièces de rechange, appelez notre service à la clientèle au 1 855 226-7169, entre 8 h et 16 h (HNE), du lundi au vendredi.