FOYER CHANDELIER MODEL #83105 Français p. 11 ATTACH YOUR RECEIPT HERE Serial Number Purchase Date Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-855-226-7169, 8 a.m. - 4 p.m., EST, Monday - Friday.
PACKAGE CONTENTS A E B I D C F H G PART A B C D E F G H I DESCRIPTION Canopy GU10 Socket G4 Socket Cable Compression Fitting Crystal Rod Mesh Cover 10-Watt G4 Bulb 35-Watt GU10 Bulb 2 QUANTITY 1 4 16 16 16 8 16 16 4
HARDWARE CONTENTS AA BB DD CC EE Ground Screw Qty: 1 Wire Short Connector Machine Anchor Screw Qty: 3 Qty: 8 Qty: 2 FF GG Mounting Bracket Qty: 1 HH Threaded Knob Qty: 2 Junction Box Cover Anchor Screw Safety Cable Loop II Canopy Screw Qty: 4 Qty: 8 Qty: 1 SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product. • • • • • WARNING IMPORTANT: NEVER attempt any work without shutting off the electricity.
SAFETY INFORMATION CAUTION • Read and understand all instructions and illustrations completely before proceeding with assembly and installation of this fixture. • If you have any doubts about how to install this lighting fixture, or if the fixture fails to operate completely, please contact a licensed electrical contractor. • All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken.
ASSEMBLY INSTRUCTIONS 2. Temporarily raise mounting bracket (DD) to ceiling. Mark location for anchor (CC). Use 9/32 size drill to drill holes for anchor (CC). Insert anchor (CC) into hole. 2 Ceiling CC Hardware Used CC Anchor x8 DD 3. Connect the mounting bracket (DD) to the outlet box with short machine screws (BB). 3 Outlet Box (Not Included) Hardware Used BB Short Machine Screw x2 DD BB DD Mounting Bracket x1 4. Screw anchor screws (HH) through mounting bracket (DD) and into anchors (CC).
ASSEMBLY INSTRUCTIONS 5. Connect safety cable located in canopy (A) to the safety cable loop located on mounting bracket (DD). 5 DD Safety Cable Loop A 6. Pass electrical wires through junction box cover (GG). Safety Cable 6 GG 7. Wire connection guide: 7 Ground wire: (bare copper or marked GND) • For installation in the United States: Wrap ground wire from outlet box around ground screw (EE) on mounting bracket (DD), no less than 2 in. from wire end. Tighten ground screw (EE).
ASSEMBLY INSTRUCTIONS 8. Supply wire connection guide: Make wire connections, securing with wire connectors (AA), following the reference chart listed below.
ASSEMBLY INSTRUCTIONS 10. Connect canopy (A) to mounting bracket (DD) with canopy screws (II). 10 DD II Hardware Used II Canopy Screw x4 A 11.Insert 35-watt max. GU10 bulb (I) into GU10 socket (B). 11 B I 12.Raise crystal rod (F) up so the smaller opening is facing up. Pass G4 socket (C) through the crystal rod (F). Insert 10-watt max. G4 bulb (H) into G4 socket (C) and secure with mesh cover (G).
CARE AND MAINTENANCE • Always be certain that electric current is turned off before cleaning this item. • Use a soft, moist cloth with mild non-abrasive soap to clean fixture. Never use glass cleaner on fixture, as it will damage the metal finish. • All glass shades may be washed in a towel-lined sink with warm water and mild soap. Do not wash shades in an automatic dishwasher. TROUBLESHOOTING PROBLEM Fixture does not light. POSSIBLE CAUSE CORRECTIVE ACTION 1. Fixture may be wired incorrectly. 1.
REPLACEMENT PARTS LIST For replacement parts, call our customer service department at 1-855-226-7169, 8 a.m. - 4 p.m., EST, Monday - Friday. PART G AA BB CC DD FF GG HH II DESCRIPTION Mesh Cover Wire Connector Short Machine Screw Anchor Mounting Bracket Threaded Knob Junction Box Cover Anchor Screw Canopy Screw AA G FF Rev.
LUSTRE D'ENTRÉE MODÈLE #83105 JOIGNEZ VOTRE REÇU ICI Numéro de série Date d’achat Des questions, des problèmes, des pièces manquantes? Avant de retourner l’article au détaillant, appelez notre service à la clientèle au 1 855 226-7169, entre 8 h et 16 h (HNE), du lundi au vendredi.
CONTENU DE L’EMBALLAGE A E B I D C F H G PIÈCE A B C D E F G H I DESCRIPTION Pavillon Douille GU10 Douille G4 Câble Raccord à compression Tige en cristal Cache-ampoule en maille Ampoule G4 de 10 watts Ampoule GU10 de 35 watts 12 QUANTITÉ 1 4 16 16 16 8 16 16 4
QUINCAILLERIE INCLUSE AA Capuchon de connexion Qté : 3 BB DD CC Vis de mise à la terre Qté : 1 Vis à métaux courtes Qté : 2 Pièce d’ancrage Qté : 8 FF EE GG Support de fixation Qté : 1 HH Boutons filetés Qté : 2 Couvercle de boîte de jonction Qté : 1 Vis à pièce d’ancrage Boucle du câble de sécurité II Vis du pavillon Qté : 4 Qté : 8 CONSIGNES DE SÉCURITÉ Veuillez vous assurer de lire et de comprendre l’intégralité du présent guide avant d’assembler, d’utiliser ou d’installer ce produit.
CONSIGNES DE SÉCURITÉ MISE EN GARDE • Prenez soin de lire et de comprendre toutes les instructions avant de commencer l’assemblage et l’installation du luminaire. • Si vous avez des doutes à propos de l’installation, ou si le luminaire ne fonctionne pas correctement, veuillez communiquer avec un électricien qualifié. • Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions.
INSTRUCTIONS POUR L'ASSEMBLAGE 2. Placez temporairement le support de fixation (DD) au plafond. Marquez les emplacements des ancrages (CC). Utilisez une perceuse équipée d'un foret de 9/32 po afin de percer les trous pour les ancrages (CC). Insérez les ancrages (CC) dans les trous. 2 Ceiling CC Quincaillerie utilisée CC Pièce d’ancrage x8 3. Fixez le support de fixation (DD) à la boîte de sortie à l’aide des vis à métaux courtes (BB).
INSTRUCTIONS POUR L'ASSEMBLAGE 5. Connectez le câble de sécurité situé dans le pavillon (A) à la boucle du câble de sécurité située sur le support de fixation (DD). 5 DD Boucle du câble de sécurité A 6. Faites passer les fils électriques à travers le couvercle du boîtier de raccordement (GG). Câble de sécurité 6 GG 7.
INSTRUCTIONS POUR L'ASSEMBLAGE 8. Guide pour la connexion des fils du cordon d’alimentation : Effectuez le raccordement des fils à l’aide des capuchons de connexion (AA), en respectant le tableau de référence ci-dessous.
INSTRUCTIONS POUR L'ASSEMBLAGE 10. Faites passer le pavillon (A) sur le support de fixation (DD) et fixez avec les vis du pavillon (II). 10 DD II Quincaillerie utilisée II Vis du pavillon x4 11. Insérez une ampoule GU10 de 35 watts max. (I) dans la douille GU10 (B). A 11 B I 12. Soulevez la tige en cristal (F) de façon à ce que la plus petite ouverture soit dirigée vers haut. Faites passer la douille G4 (C) dans la tige en cristal (F). Insérez une ampoule G4 de 10 watts max.
ENTRETIEN • Vérifiez toujours que le courant est coupé avant de nettoyer le luminaire. • Utilisez un linge doux et humide ainsi qu’un savon non abrasif. N’utilisez jamais de nettoyants pour vitres; vous risqueriez d’endommager le fini métallique du luminaire. • Les abat-jour en verre peuvent être nettoyés dans un évier couvert de serviettes, à l’aide d’eau tiède et de savon doux. Ne nettoyez pas les abat-jour dans un lave-vaisselle. DÉPANNAGE PROBLÈME Le luminaire ne s’allume pas.
LISTE DES PIÈCES DE RECHANGE Pour obtenir des pièces de rechange, appelez notre service à la clientèle au 1 855 226-7169, entre 8 h et 16 h (HNE), du lundi au vendredi. PIÈCE G AA BB CC DD FF GG HH II DESCRIPTION Cache-ampoule en maille Capuchon de connexion Vis à métaux courtes Pièce d’ancrage Support de fixation Boutons filetés Couvercle de boîte de jonction Vis à pièce d’ancrage Vis du pavillon AA G FF Rev.