7-LIGHT SPIRAL PENDANT MODEL #83134 Français p. 11 ATTACH YOUR RECEIPT HERE Serial Number Purchase Date Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-855-226-7169, 8 a.m. - 4 p.m., EST, Monday - Friday.
PACKAGE CONTENTS H A C E G F D B PART A B C D E F G H DESCRIPTION Canopy Crystal Cable Threaded Cap Socket Crystal Support 20-Watt G4 Bulb Compression Fitting 2 QUANTITY 1 7 7 7 7 7 7 7
HARDWARE CONTENTS AA BB DD CC EE Ground Screw Qty: 1 Short Wire Connector Machine Anchor Screw Qty: 3 Qty: 4 Qty: 2 HH Threaded Knob Qty: 2 Mounting Bracket Qty: 1 GG FF Safety Cable Loop II Canopy Knob Qty: 4 Anchor Screw Junction Box Cover Qty: 4 Qty: 1 SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product. • • • • • WARNING IMPORTANT: NEVER attempt any work without shutting off the electricity.
SAFETY INFORMATION CAUTION • Read and understand all instructions and illustrations completely before proceeding with assembly and installation of this fixture. • If you have any doubts about how to install this lighting fixture, or if the fixture fails to operate completely, please contact a licensed electrical contractor. • All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken.
ASSEMBLY INSTRUCTIONS 2. Connect the mounting bracket (DD) to the outlet box with short machine screws (BB). 2 Outlet Box (Not Included) Hardware Used BB Short Machine Screw x2 DD BB DD Mounting Bracket x1 3. Screw anchor screws (GG) through mounting bracket (DD) and into anchors (CC). 3 CC DD Hardware Used GG Anchor GG Screws 4. x4 The hanging length of the cable (C) for this fixture is adjustable.
ASSEMBLY INSTRUCTIONS 5. Connect safety cable located in canopy (A) to the safety cable loop located on mounting bracket (DD). 5 DD Safety Cable Loop Safety Cable A 6. Pass electrical wires through junction box cover (HH).
ASSEMBLY INSTRUCTIONS 7. Wire connection guide: 7 Ground wire: • For installation in the United States: Wrap ground wire from outlet box around ground screw (EE) on mounting bracket (DD) no less than 2 in. from wire end. Tighten ground screw (EE). If fixture is supplied with a ground wire, connect to outlet ground wire with a wire connector (AA). • For installation in Canada: If fixture is supplied with ground wire, wrap ground wire around ground screw (EE) on mounting bracket (DD).
ASSEMBLY INSTRUCTIONS 9. 9 Pass canopy (A) over mounting bracket (DD) and secure with canopy knobs (II). DD A Hardware Used II Canopy Knob x4 II 10. Insert 20-watt max. G4 base bulb (G) into socket (E). Screw crystal support (F) onto socket (E). Pass crystal (B) over crystal support (F) and secure with threaded cap (D). 10 E Note: Never touch a halogen light bulb with your bare skin, even when removing the bulb from the package before installing.
CARE AND MAINTENANCE • Always be certain that electric current is turned off before cleaning this item. • Use a soft, moist cloth with mild non-abrasive soap to clean fixture. Never use glass cleaner on fixture, as it will damage the metal finish. • All glass shades may be washed in a towel-lined sink with warm water and mild soap. Do not wash shades in an automatic dishwasher. TROUBLESHOOTING PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Fixture does not light. 1. Fixture may be wired incorrectly. 2.
REPLACEMENT PARTS LIST For replacement parts, call our customer service department at 1-855-226-7169, 8 a.m. - 4 p.m., EST, Monday - Friday. PART B D F AA BB CC DD FF GG HH II DESCRIPTION Crystal Threaded Cap Crystal Support Wire Connector Short Machine Screw Anchor Mounting Bracket Threaded Knob Anchor Screw Junction Box Cover Canopy Knob D B FF Rev.
LUMINAIRE SUSPENDU EN SPIRALE À 7 LUMIÈRES MODÈLE #83134 JOIGNEZ VOTRE REÇU ICI Numéro de série Date d’achat Des questions, des problèmes, des pièces manquantes? Avant de retourner l’article au détaillant, appelez notre service à la clientèle au 1 855 226-7169, entre 8 h et 16 h (HNE), du lundi au vendredi.
CONTENU DE L’EMBALLAGE H A C E G F D B PIÈCE A B C D E F G H DESCRIPTION Pavillon Cristal Câble Capuchon fileté Douille Support du cristal Ampoule G4 de 20 watts Raccord à compression 12 QUANTITÉ 1 7 7 7 7 7 7 7
QUINCAILLERIE INCLUSE AA BB DD CC EE Vis de mise à la terre Qté : 1 Capuchon de connexion Vis à métaux Qté : 3 courtes Qté : 2 Pièce d’ancrage Qté : 4 Support de fixation Qté : 1 GG HH FF Boutons filetés Qté : 2 Boucle du câble de sécurité II Bouton du pavillon Qté : 4 Couvercle de Vis à pièce boîte de jonction d’ancrage Qté : 1 Qté : 4 CONSIGNES DE SÉCURITÉ Veuillez vous assurer de lire et de comprendre l’intégralité du présent guide avant d’assembler, d’utiliser ou d’installer ce produit.
CONSIGNES DE SÉCURITÉ MISE EN GARDE • Prenez soin de lire et de comprendre toutes les instructions avant de commencer l’assemblage et l’installation du luminaire. • Si vous avez des doutes à propos de l’installation, ou si le luminaire ne fonctionne pas correctement, veuillez communiquer avec un électricien qualifié. • Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions.
INSTRUCTIONS POUR L'ASSEMBLAGE 2. Fixez le support de fixation (DD) à la boîte de sortie à l’aide des vis à métaux courtes (BB). 2 Boîte de sortie (non incluse) Hardware Used BB Vis à métaux courtes x2 DD BB DD Support de fixation x1 3. Vissez les vis d'ancrage (GG) à travers le support de fixation (DD) et dans les ancrages (CC). 3 CC DD Quincaillerie utilisée GG Vis à pièce GG d’ancrage 4. x4 La longueur des câbles de suspension (C) de ce luminaire est réglable.
INSTRUCTIONS POUR L'ASSEMBLAGE 5. Connectez le câble de sécurité situé dans le pavillon (A) à la boucle du câble de sécurité située sur le support de fixation (DD). 5 DD Boucle du câble de sécurité A 6. Faites passer les fils électriques à travers le couvercle du boîtier de raccordement (HH).
INSTRUCTIONS POUR L'ASSEMBLAGE 7. Guide de raccordement électrique 7 Fil de mise à la terre : • Pour une installation aux États-Unis : enroulez le fil de mise à la terre provenant de la boîte de sortie autour de la vis de mise à la terre (EE) située sur le support de fixation (DD), à au moins 5 cm (2 po) de l’extrémité du fil. Serrez la vis de mise à la terre (EE).
INSTRUCTIONS POUR L'ASSEMBLAGE 9. 9 Placez le pavillon (A) sur le support de fixation (DD) et fixez à l'aide des boutons du pavillon (II). DD A Quincaillerie utilisée II Bouton du pavillon x4 II 10. Insérez une ampoule G4 de 20 watts max. (G) dans la douille (E). Vissez le support du cristal (F) dans la douille (E). Placez le cristal (B) sur le support du cristal (F) et fixez à l'aide du capuchon fileté (D).
ENTRETIEN • Vérifiez toujours que le courant est coupé avant de nettoyer le luminaire. • Utilisez un linge doux et humide ainsi qu’un savon non abrasif. N’utilisez jamais de nettoyants pour vitres; vous risqueriez d’endommager le fini métallique du luminaire. • Les abat-jour en verre peuvent être nettoyés dans un évier couvert de serviettes, à l’aide d’eau tiède et de savon doux. Ne nettoyez pas les abat-jour dans un lave-vaisselle. DÉPANNAGE PROBLÈME Le luminaire ne s’allume pas.
LISTE DES PIÈCES DE RECHANGE Pour obtenir des pièces de rechange, appelez notre service à la clientèle au 1 855 226-7169, entre 8 h et 16 h (HNE), du lundi au vendredi. PIÈCE B D F AA BB CC DD FF GG HH II DESCRIPTION Cristal Capuchon fileté Support du cristal Capuchon de connexion Vis à métaux courtes Pièce d’ancrage Support de fixation Boutons filetés Vis à pièce d’ancrage Couvercle de boîte de jonction Bouton du pavillon D B FF Rev.