Specifications

complete
77
©2004 ELAN HOME SYSTEMS • Lexington, KY USA • All Rights Reserved.
ACCESSORIES
The PVSE Precision Panel makes it easy to
connect up to six VSE Electronic Volume
Controls to any ELAN system, and is also
the perfect trim-out solution for VSEs in
any stand-alone system.
The PVSE is one of ELAN’s new ‘half-frame’
Precision Panels. Two ‘half-frame’ panels
can be mounted in one standard-size
Precision Panel frame, giving you the
flexibility to mix and match the Precision
Panels you need to complete a neat,
problem-free trim-out.
The back of the PVSE features six clearly
labeled 110 punch-down blocks that
provide independent connections for
Override, IR and Sense; plus two additional
punch-down connectors for easy routing of
VSE IR signals to the new System12
Precision Panel (PS12). Two RJ-45 jacks on
the rear of the panel make it easy to route
override signals from the new PZ600
Communication Controller Precision Panel,
and to link multiple PVSE panels together.
There’s also a bank of six dipswitches that
allow you to turn the front-panel VSE-
specific IR Out ports into ‘ALL’ ports.
In stand-alone applications, this allows all
six VSEs to control any or all sources.
The PVSE’s front panel was designed with
stand-alone applications in mind. Six
+12VDC trigger inputs, plus a trigger ‘ALL’
port, allow you to mute any or all VSEs
whenever voltage is not present. Six IR
inputs, plus an ‘ALL’ port, allow an SR1
Sense/Relay/IR Controller to independently
control VSEs connected to the panel. Six IR
OUT ports, plus an IR OUT ‘ALL’ port, allow
each or all VSEs to control source
components in a stand-alone system.
The VSEs are powered by an ELAN PWR12
+12VDC, 2A Power Supply (included).
PVSE VSE ELECTRONIC VOLUME CONTROL
PRECISION PANEL
FEATURES & SPECS
1/2-frame Precision Panel for 6 VSE
Electronic Volume Controls
Easy to interface with PS12 and
PZ600 Precision Panels
Multiple PVSEs can be linked together
110 punch-down connectors with
clearly labeled silkscreen for
error-free terminations
Front panel trigger, IR IN/OUT jacks
for stand-alone applications
PWR12 12V, 2A power supply included
Fits in PF2 Precision Panel Frame
(required for installation, see pg. 82)
The PV12 Video Precision Panel provides you
with a clean and easy way to connect up to
12 runs of coaxial cable for composite and
component video to the System12 A/V
Controller or Z•880 Video Controller.
Eight gold-plated F-to-RCA barrel connec-
tors are mounted on flanges angled at 45º.
The angled flanges ensure that all your
coax runs slide easily back into the wall
after termination, and that the cables are
not bent past their specified limits, which
can cause damage resulting in signal loss.
The PV12 is one of ELAN’s new ‘half-frame’
Precision Panels. Two ‘half-frame’ panels
can be mounted in one PF2 Precision Panel
Frame, giving you the flexibility to mix and
match the Precision Panels you need to
complete a neat, problem-free trim-out.
One PV12 can accommodate all 8 video
outputs of a Z•880 Video Controller.
Two PV12s can be mounted in one frame
to accommodate the 16 video outputs
of the System12.
PV12 VIDEO PRECISION PANEL
FEATURES & SPECS
1/2-frame Video Precision Panel
12 F-to-RCA connectors
Angled flanges for easy and safe
coax wire management
Perfect for use with S12 A/V Controller
and Z•880 Video Controller
Fits in PF2 Precision Panel Frame
(required for installation, see pg. 82)
Ac_FINAL.qxd 1/24/05 5:01 PM Page 77