PLATINUM SPOT 15R PRO KEEP THIS MANUAL FOR FUTURE NEEDS
Thank you for your patronage. We are confident that our excellent products and service can satisfy you. For your own safety, please read this user manual carefully before installing the device. In order to install , operate, and maintain the lighting safety and correctly. We suggest that the installation and operation should be done by the verified technician and follow the instruction strictly.
·Iris from 5%~100% with pulse iris effect. ·Zoom: 9°~27° linear zoom ·Strobe/shutter: High speed shutter, 0-13 Hz or random strobe ·Control board with full color LCD graphic display and touch-keyboard ·Auto-program: 7 pre-built programs can be selected.
SAFETY INSTRUCTIONS This device has left the factory in perfect condition. In order to maintain this condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual. Important: Damages caused by the disregard of this user manual are not subject to warranty. The dealer will not accept liability for any resulting defects or problems.
Please be aware that damages caused by manual modifications to the device are not subject to warranty. Keep away from children and non-professionals. GENERAL GUIDELINES This device is a lighting effect for professional use on stages, in discotheques, theatres, etc., the device was designed for indoor use only. This fixture is only allowed to be operated with the max alternating current which stated in the technical specifications in the last page of this manual.
reach very high temperature. During the installation of halogen lamps do not touch the glass bulbs bare handed. Always use a cloth to handle the lamps during insertion and removal. Do not install lamps with a higher wattage. They generate higher temperatures than which the device was designed for. For the installation, you need one: PLATINUM 15R Procedures: 1) Unscrew the 3 screws (A, B, C) on the bottom of the housing, holding the plate where the lamp is underneath. Carefully remove the metal plate.
Overhead mounting requires extensive experience, including amongst others calculating working load limits, installation material being used, and periodic safety inspection of all installation material and the device. If you lack these qualifications, do not attempt the installation yourself. Improper installation can result in bodily injury. Before mounting make sure that the installation area can hold a minimum point load of 10 times the device’s weight.
d) Pull the safety-rope through the holes on the bottom of the base and over the trussing system or a safe fixation spot. Insert the end in the carabine and tighten the safety screw. Notice: this step is quite important to ensure that the fixture will not drop out by the damage of the clamp. DMX-512 control connection Connect the provided XLR cable to the female 3-pin XLR output of your controller and the other side to the male 3-pin XLR input of the moving head.
Projector DMX start address selection All fixtures should be given a DMX starting address when using a DMX signal, so that the correct fixture responds to the correct control signals. This digital starting address is the channel number from which the fixture starts to “listen” to the digital control information sent out from the DMX controller. The allocation of this starting address is achieved by setting the correct number on the display located on the base of the device.
1)Connect the transmitter with the DMX controller 2)To make the fixture installed with wireless receiver log in to the transmitter a) Initially, the indicator on the receiver fixture should be in Solid red b) Press and hold the configuration button on transmitter for less than 3 seconds the red/ green LEDs on the transmitter and the receiver fixture will flash rapidly for about 5~ 10 seconds while the system goes through its setup procedure.
To access the display menu via the internal battery, press the DC switch button for 2seconds; To shut off the display immediately, choose the commend " Reset All" menu and press "Enter" button, otherwise, the display will automatically switch off about 1 minute from last button press.
Wireless DMX De-Act WDMX Activate WDMX Act & Data Out Rest WDMX Mem Reset Default ON/OFF De-activate WDMX Activate WDMX Act & Data Out Reset Wireless DMX Mem Restore factory set.
“Set DMX Address” - DMX address setting – This function is used to set or adjust the fixture’s starting DMX address. Every device controlled by DMX has to have a unique starting address. The addressing feature is what allows DMX to function properly. The DMX address of a fixture is what allows it to communicate with a controller properly. The DMX addressing also allows the fixture to ignore any DMX information coming from the controller that is not meant specifically for the fixture.
Information: Time information These functions will detail different time functions associated with the fixture. Current Time This function displays the running time of the fixture from the last power on. The display shows “XXXX”, where “XXXX” represents the number of hours the fixture has been running. This counter is automatically reset after every power-on. Total Run Time This function tracks the total running time of the fixture from the very first startup.
Clear Lamp Time This function resets the lamp “ON” time to zero. Please reset the lamp “ON” time at every lamp replacement. This procedure tracks the lamp running time so the lamp can be replaced at the end of it’s recommended duty cycle. • Select “Clear lamp time” in the system menu. • The LCD will display “ON” or “OFF.” Were “ON” will reset the lamp time. • Press enter to confirm. • Press the Mode/Esc-button to return to the main menu. Temperature Info.
When engaged, this function will allow the lamp to be switched “off” via a DMX controller. Select “ON” to enable this function or “OFF” to disable it. Lamp On at Temp. The fixture is designed to shut the lamp off when an excessive temperature is sensed inside the head by the on-board CPU. The lamp is shut down to prevent damage to the lamp and avoids possible internal damage to the head. This function sets the minimum temperature for lamp restrike after the lamp has been automatically shut off.
No DMX Status – This function dictates how the fixture will function if it looses DMX signal during normal operation. The default function is set to hold, in which the fixture will lock into the last DMX signal it received and remain in that position until it is turned off or begins receiving a new DMX signal. If the fixture is turned on without any DMX signal, the fixture will automatically go in to soundactive mode. Available settings are: “Close” – Shutter flags will close.
original DS-250. Tilt speed will be the same as speed 2. Mic Sensitivity – This function makes the internal microphone more or less sensitive to sound. This function only works in conjunction with the sound active modes. The default setting is 70% and setting range from 0% to 99%. Hibernation – When activated, this function will automatically put the fixture in power stand-by mode after a defined period of time of no DMX activity.
the menu commands. Temperature C/F – This function changes the temperature the unit will display from either Celsius or Fahrenheit. Fahrenheit is set as the default measurement. Initial effect – This function allows a user to create and assign a custom “Home Position” into the fixture. Adjusting the Pan and Tilt values then locking those values into the fixture’s internal memory creates the new “Home” position. Wireless DMX This section will control the functionality of the built-in wireless DMX receiver.
fixture channel and test it’s function independently from the control board. Lamp adjustment (manual control) – This function readies the fixture for lamp optimization in a simple single step procedure. This function will center the pan and tilt motors and at the same time open the shutter and bring the dimmer to 100%. The pan and tilt function will still operate if the fixture needs to be positioned to a flat clear surface. For more information on lamp optimization please see Section 6/Page 14.
Select program – This function allows the user to select one of ten of the user defined built-in programs. This program is then accessed in “Function Mode” under “Program Run.” Edit program – This function allows the user to edit the built-in programs. Edit Scenes – This function allows the user to edit or define the actual scenes that are stored in the user defined built-in programs that are accessed in the previous step. Rec Controller - The Platinum Spot 5R features an integrated DMX recorder.
INSTRUCTIONS ON USE: DMX channel´s functions and their values (34 DMX channels): Mode/Channel Value Function St Ba Ex PAN Movement 8bit : 1 1 1 0-255 Pan Movement By 540/630 Pan Fine 16bit 2 2 0-255 Fine control of Pan movement TILT Movement 8bit : 3 2 3 0-255 Tilt Movement By 270 Tilt Fine 16bit 4 4 0-255 Fine control of Tilt movement Color Wheel : Color Wheel : 0-18 Open / white 19-37 Color 1 38-56 Color 2 57-75 Color 3 5 3 5 76-94 Color 4 95-113 Color 5 114-127 Color 6 128-189 Forwards rainbow effect fro
9 10 7 8 13 14 15 11 9 16 50-59 60-69 70-79 80-89 90-104 105-119 120-134 135-149 150-164 165-179 180-194 195-209 210-255 0-127 128-189 190-193 194-255 0-255 0-7 8-15 16-23 24-31 32-39 40-47 48-55 56-63 64-71 72-79 80-87 88-95 96-103 104-111 112-119 120-126 127-133 134-140 141-147 148-154 155-161 162-168 169-175 Rot. gobo 5 Rot. gobo 6 Rot. gobo 7 Rot. gobo 8 Rot. gobo 1 shake Rot. gobo 2 shake Rot. gobo 3 shake Rot. gobo 4 shake Rot. gobo 5 shake Rot. gobo 6 shake Rot. gobo 7 shake Rot.
176-182 183-189 190-196 197-203 204-210 211-217 218-255 17 12 13 10 11 18 19 20 14 12 21 22 15 13 23 24 0-255 0-31 32-127 128-135 136-143 144-151 152-159 160-167 168-175 176-183 184-191 192-199 200-207 208-215 216-223 224-231 232-239 240-247 248-255 0-127 128-189 190-193 194-255 0-255 0-255 0-255 0-255 0-255 Gobo 9 shake slow to fast Gobo 10 shake slow to fast Gobo 11 shake slow to fast Gobo 12 shake slow to fast Gobo 13 shake slow to fast Gobo 14 shake slow to fast Gobo wheel rotation from sl
16 14 25 17 15 26 27 18 16 28 29 19 17 30 20 18 31 21 19 32 0-31 32-63 64-95 96-127 128-159 160-191 192-223 224-255 0-255 0-255 0-191 192-223 224-255 0-255 0-191 192-223 224-254 255 0-255 0-225 226-235 236-245 246-255 0-7 8-15 16-23 24-31 32-39 40-47 48-55 56-63 64-71 72-79 80-87 88-95 96-103 104-111 Shutter closed No function (shutter open) Strobe effect slow to fast No function (shutter open) Pulse-effect in sequences No function (shutter open) Random strobe effect slow to fast No func
22 23 20 21 33 34 112-119 120-127 128-135 136-143 144-151 152-159 160-167 168-175 176-183 184-191 192-199 200-207 208-215 216-223 224-231 232-239 240-247 248-255 0-19 20-29 30-39 40-59 60-79 80-84 85-87 88-90 91-93 94-96 97-99 100-119 120-139 140-159 160-179 180-199 200-219 220-239 240-255 Macro14 Macro15 Macro16 Macro17 Macro18 Macro19 Macro20 Macro21 Macro22 Macro23 Macro24 Macro25 Macro26 Macro27 Macro28 Macro29 Macro30 Random CMY Lamp on/off, reset, internal programs: Colour change normal Colour
PAN- movement Er (PAN-yoke movement error) This message will appear after the reset of the fixture if the yoke’s magneticindexing circuit malfunction (sensor failed or magnet missing) or the stepping-motor is defective (or its driving IC on the main PCB). The PAN- movement is not located in the default position after the reset.
CLEANING AND MAINTENANCE The following points have to be considered during the inspection: 1) All screws for installing the devices or parts of the device have to be tightly connected and must not be corroded. 2) There must not be any deformations on the housing, color lenses, fixations and installation spots (ceiling, suspension, trussing). 3) Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances.
- - 29 XM542-V1.