Design LED 36 Elation Professional™ 4295 Charter Street Los Angeles, Ca 90058 www.elationlighting.com Rev.
DESIGN LED 36™ ©Elation Professional, Los Angeles Ca. 1 www.ElationLighting.
DESIGN LED 36™ TABLE OF CONTENS CONTENTS 1. General Information……………………………………………………………………… 3 a. Introduction………………………………………………………………………. 3 b. Unpacking………………………………………………………..…………..… c. 3 Customer Support…………………………………………….………………… 3 d. Warranty Registration……………………………………………………..…… 4 2. Safety Instructions………………………………………………………........…………. 5 3. Features…………………………………………………………………………………… 7 4. General Guidelines………………………………………………………………………. 8 5. Fixture Overview…………………………………………………………………………. 9 6.
DESIGN LED 36™ 1. GENERAL INFORMATION INTRODUCTION: Congratulations, you have just purchased one of the most innovative and reliable LED fixtures on the market today! The DESIGN LED 36,™ has been designed to perform reliably for years when the guidelines in this booklet are followed. Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this unit. These instructions contain important information regarding safety during use and maintenance.
DESIGN LED 36™ yourself. Doing so will void your manufactures warranty. Please do not discard the shipping carton in the trash. Please recycle whenever possible. WARRANTY REGISTRATION: The DESIGN LED 36™ carries a two year (730 days) limited warranty. Please fill out the enclosed warranty card to validate your purchase. All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number. The R.A.
DESIGN LED 36™ 2. SAFETY INSTRUCTIONS To guarantee proper and consistent operation, it is important to follow the guidelines in this manual. Elation Professional will not accept responsibility for damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual. 1. Always be sure that the fan and the air inlets remain clean and are never blocked. Allow about 6” (15cm) between this fixture and other devices or a wall to allow for proper cooling. 2.
DESIGN LED 36™ damaged, replace it immediately with a new one of similar power rating. 13. Always disconnect from main power before performing any type of service or any cleaning procedure. 14. Only handle the power cord by the plug. Never pull out the plug by tugging the wire portion of the cord. 15. Please be aware that damages caused by manual modifications to the device are not subject to warranty.
DESIGN LED 36™ 3.
DESIGN LED 36™ 4. GENERAL GUIDELINES This fixture is a professional lighting effect designed for use on stage, in nightclubs, in theatres, and other types of architectural installations. Do not attempt operation or installation without a proper knowledge on how to do so. This fixture was designed for indoor use only; use of this fixture outside will void the manufacture’s warranty. Consistent operational breaks will ensure that the fixture will function properly for many years to come.
DESIGN LED 36™ 5. FIXTURE OVERVIEW 1. Venting Slots 2. Exterior Housing 3. Hanging Bracket 4. Diffusion Lens 5. LED Assembly 6. Power Cord 7. On/Off Switch 8. DMX In Jack 9. DMX Out Jack 10. Fuse Holder Housing 11. Dipswitch Assembly 1. Venting Slots – These slots are designed to keep the fixture cool during operation. Never block these slots. Keep these slots clean at all times. 2. Exterior Housing – The exterior housing is constructed of rugged polymer material. 3.
DESIGN LED 36™ hung, mounted, or stood straight up. 4. Diffusion Lens – This lens is used to both protect the LEDs as well a diffuse the light output. 5. LED Assembly – 36 1-watt LEDs construct the LED assembly. 6. Power Cord – Provides main power to the unit. 7. On/Off Power Switch – Controls main power to the unit. 8. DMX In Jack – This jack accepts an incoming DMX signal via a male, 3-pin XLR jack. 9.
DESIGN LED 36™ 6. MOUNTING AND INSTALLATION Cautions: For added protection mount the fixtures in areas outside walking paths, seating areas, or in areas were the fixture might be reached by unauthorized personal. Before mounting the fixture to any surface, make sure that the installation area can hold a minimum point load of 10 times the device’s weight. Fixture installation must always be secured with a secondary safety attachment, such as an appropriate safety cable.
DESIGN LED 36™ Rigging Points Overhead mounting requires extensive experience, including among others calculating working load limits, a fine knowledge of the installation material being used, and periodic safety inspection of all installation material and the fixture. If you lack these qualifications, do not attempt the installation yourself. Improper installation can result in bodily injury. Be sure to complete all rigging and installation procedures before connecting main power.
DESIGN LED 36™ fixture. See illustration on next page. Securing the Design LED 36™ Regardless of the rigging option you choose for your Design LED 36™ always be sure to secure your fixture with a safety cable. The fixture provides a built-in rigging point for a safety cable on the hanging bracket as illustrated above. Be sure to only use the designated rigging point for the safety cable and never secure a safety cable to a carrying handle. ©Elation Professional, Los Angeles Ca. 13 www.ElationLighting.
DESIGN LED 36™ 7. UNDERSTANDING DMX Data Cable (DMX Cable) Requirements (For DMX and Master/Slave Operation): Your fixture and your DMX controller require a standard 3-pin XLR connector for data input and data output (see figure below). If you are constructing your own cables be sure to use two conductor shielded digital cable rated at a 120 ohms (this cable can be purchased at almost all professional sound and lighting stores).
DESIGN LED 36™ Branch 4™ or DMX Branch/4™. DMX-512 connection with DMX terminator When longer runs of cable are used, you may need to use a terminator on the last fixture to avoid erratic behavior. A terminator is a 90-120 ohm 1/4 watt resistor that is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This fixture is inserted in the female XLR connector of the last fixture in your daisy chain to terminate the line.
DESIGN LED 36™ Understanding Fixture DMX addressing; All fixtures should be given a DMX starting address when using a DMX controller, so the correct fixture responds to the correct control signal. This digital starting address is the channel number from which the fixture starts to “listen” to the digital control information sent out from the DMX controller. The allocation of this starting DMX address is achieved by combining various dipswitches located on the rear of the fixture.
DESIGN LED 36™ fixture. In the case of the Design LED 36™, which is a 6 channel fixture, you should set the starting DMX address of the first unit to 1, the second unit to 7 (6 + 1), the third unit to 13 (6 + 7), and so on. The chart on page 19 details the proper starting DMX address dipswitch setting combination. NOTE: The Design LED 36 contains a total of 12 dipswitches. Only use dipswitches 1~9 to set the DMX address.
DESIGN LED 36™ GREEN: Dipswitch 3 & 4 off, the green value is 0 Dipswitch 3 is on and dipswitch 4 is off, the green value is 60 Dipswitch 3 is off and dipswitch 4 is on, the green value is 125 Dipswitch 3 is on and dipswitch 4 is on, the green value is 255 BLUE: Dipswitch 5 & 6 is off, the blue value is 0 Dipswitch 5 is on and dipswitch 6 is off, the blue value is 60 Dipswitch 5 is off and dipswitch 6 is on, the blue value is 125 Dipswitch 5 is on and dipswitch 6 is on, the blue value is 255 When dipswitch
DESIGN LED 36™ 8. DMX CHANNEL TRAITS: 6 Channel Mode: CHANNEL 1:Red CHANNEL 2:Green CHANNEL 3:Blue CHANNEL 4: Internal programs: CHANNEL 5:Strobe CHANNEL 6: Dimming (0%-100%) ©Elation Professional, Los Angeles Ca. 19 www.ElationLighting.
DESIGN LED 36™ DMX channel’s functions and their values: Channel 1 - Red: 0-255 Red (0-Black, 255-100% Red) Channel 2 - Green: 0-255 Green (0-Black, 255- 100% Green) Channel 3 - Blue: 221-255 Blue (0-Black, 255- 100% Blue) Channel 4 - Internal programs: 0-10 No function 11-40 Internal program 1 41-70 Internal program 2 71-100 Internal program 3 101-130 Internal program 4 131-160 Internal program 5 161-190 Internal program 6 191-220 Internal program 7 221-255 Internal program 8 Chann
DESIGN LED 36™ Channel 6 - General dimming 0-255 Dimming (2%-100%) DMX OPERATION: 3 Channel Mode: CHANNEL 1: Red CHANNEL 2: Green CHANNEL 3: Blue ©Elation Professional, Los Angeles Ca. 21 www.ElationLighting.
DESIGN LED 36™ DMX channel’s functions and their values: Channel 1 - Red: 0-255 Red (0-100% Red) Channel 2 - Green: 0-255 Green (0-100% Green) Channel 3 - Blue: 0-255 Blue (0-100% Blue) ©Elation Professional, Los Angeles Ca. 22 www.ElationLighting.
DESIGN LED 36™ ©Elation Professional, Los Angeles Ca. 23 www.ElationLighting.
DESIGN LED 36™ 9. CLEANING AND MAINTENANCE The consider the following point during normal service and inspection: 1. Be sure all screws and fasteners are securely tightened at all times. Lose screws may fall out during normal operation resulting in damage or injury as larger parts could fall. 2. All mechanical parts and motors should not show any traces of serious wear and should rotate freely. 3. Electric power supply cables must not show any damage, material fatigue or sediments.
DESIGN LED 36™ 10. 2-YEAR LIMITED WARRANTY A. Elation Professional® hereby warrants, to the original purchaser, Elation Professional® products to be free of manufacturing defects in material and workmanship for a period of two years, (730 days) from the date of purchase. This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories.
DESIGN LED 36™ identifying marks to that effect. E. Elation Professional® reserves the right to make changes in design and/or improvements upon its products without any obligation to include these changes in any products theretofore manufactured. F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above.
DESIGN LED 36™ 11. PHOTOMETRIC DATA ©Elation Professional, Los Angeles Ca. 27 www.ElationLighting.
DESIGN LED 36™ 12. DIMENSIONAL DRAWINGS ©Elation Professional, Los Angeles Ca. 28 www.ElationLighting.
DESIGN LED 36™ 13. CIRCUIT SCHEMATIC ©Elation Professional, Los Angeles Ca. 29 www.ElationLighting.
DESIGN LED 36™ 14. TECHNICAL SPECIFICATIONS Power supply: 120vAC~60Hz Power consumption: MAX 75W Packing dimensions: 24 x 24 x17 cm Weight: 4.5 kg DMX Channels: 6 Channel mode or 3 Channel mode Drive: Standard DMX-512, 3 pole XLR; [+] = Pin 3 [-] = Pin 2 [Ground] = Pin 1.
DESIGN LED 36™ Elation Professional 4295 Charter Street Los Angeles, CA. 90058 323-582-3322 / 323-582-3108 fax ©Elation Professional, Los Angeles Ca. 31 www.ElationLighting.
DESIGN LED 36™ www.ElationLighting.com /Info@ElationLighitng.com ©Elation Professional, Los Angeles Ca. 32 www.ElationLighting.