Design LED 36 Pro Elation Professional™ 6122 S. Eastern Ave. Los Angeles, Ca 90040 www.elationlighting.com Rev. 10/04/2009 – visage Ver. 1.
DESIGN LED 36 Pro™ ©Elation Professional, Los Angeles Ca. 1 www.ElationLighting.
DESIGN LED 36 Pro™ TABLE OF CONTENS 1. General Information……………………………………………………………………… 3 a. Introduction………………………………………………………………………. 3 b. Unpacking………………………………………………………..…………..….. 3 c. Customer Support…………………………………………….………………… 3 d. Warranty Registration…………………………………………………………… 4 2. Safety Instructions………………………………………………………........…………. 5 3. Features…………………………………………………………………………………… 7 4. General Guidelines………………………………………………………………………. 8 5. Fixture Overview…………………………………………………………………………. 9 6.
DESIGN LED 36 Pro™ 1. GENERAL INFORMATION INTRODUCTION: Congratulations, you have just purchased one of the most innovative and reliable LED fixtures on the market today! The Design LED 36 Pro™ has been designed to perform reliably for years when the guidelines in this booklet are followed. Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this unit. These instructions contain important information regarding safety during use and maintenance.
DESIGN LED 36 Pro™ yourself. Doing so will void your manufactures warranty. Please do not discard the shipping carton in the trash. Please recycle whenever possible. WARRANTY REGISTRATION: The Design LED 36 Pro™ carries a two year (730 days) limited warranty. Please fill out the enclosed warranty card to validate your purchase. All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number. The R.A.
DESIGN LED 36 Pro™ 2. SAFETY INSTRUCTIONS To guarantee proper and consistent operation, it is important to follow the guidelines in this manual. Elation Professional will not accept responsibility for damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual. 1.
DESIGN LED 36 Pro™ 10. Never open this fixture while in use. 11. This device falls under protection-class I. Therefore it is essential that the device be grounded properly. 12. Qualified personnel should perform all electrical connections. 13. Be sure the available voltage matches the voltage requirements of the unit. Be sure the power cord is never crimped or damaged. If the power cord is damaged, replace it immediately with a new one of similar power rating. 14.
DESIGN LED 36 Pro™ 3.
DESIGN LED 36 Pro™ 4. GENERAL GUIDELINES This fixture is a professional lighting effect designed for use on stage, in nightclubs, in theatres, and other types of architectural installations. Do not attempt operation or installation without a proper knowledge on how to do so. This fixture was designed for indoor use only; use of this fixture outside will void the manufacture’s warranty. Consistent operational breaks will ensure that the fixture will function properly for many years to come.
DESIGN LED 36 Pro™ 5. FIXTURE OVERVIEW 1. LED Lens Assembly – The lens assembly may be user replaced in the event repair is needed or a different beam angle is required. ©Elation Professional, Los Angeles Ca. 9 www.ElationLighting.
DESIGN LED 36 Pro™ 2. LED Display – 4-segment menu display. Used to display the DMX address as well as all other menu functions. 3. Power Output Lead – This lead is used to jump power to another Design LED 36 Pro™. Please do not daisy-chain power for more than 16 fixtures. 4. DMX Out Lead – XLR female lead. This lead is used to send an incoming DMX signal to the next fixture in the DMX chain. 5. Menu Button – This button is used to access the fixtures menu functions. 6.
DESIGN LED 36 Pro™ 6. MOUNTING AND INSTALLATION Cautions: For added protection mount the fixtures in areas outside walking paths, seating areas, and away from areas were unauthorized personnel might reach the fixture. Before mounting the fixture to any surface, make sure that the installation area can hold a minimum point load of 10 times the device’s weight. Fixture installation must always be secured with a secondary safety attachment, such as an appropriate safety cable.
DESIGN LED 36 Pro™ Mounting The Design LED 36 Pro™ is fully operational in any mounting position, hanging upside-down, side mounted, or set on a flat level surface, etc. Be sure this fixture is kept at least 0.5m (1.5 feet) away from any flammable materials (decoration etc.). When clamp mounting; always use and install the supplied safety cable as an added safety measure to prevent accidental damage in the event of a clamp failure. See the image below.
DESIGN LED 36 Pro™ added safety measure be sure to attach at least one properly rated safety cable to the fixture. See illustrations below. Securing the Design LED 36 Pro™ Always be sure to secure your fixture with a safety cable when suspending the unit from truss or other means. The fixture provides a built-in rigging point for a safety cable as illustrated above. Be sure to only use the designated rigging point for the safety cable and never secure a safety cable to the hanging bracket.
DESIGN LED 36 Pro™ 7. UNDERSTANDING DMX DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by most lighting and controller manufactures as a form of communication between intelligent fixtures and controllers. DMX allows all makes and models of different manufactures to be linked together and operate from a single controller. This is possible as long as all the fixtures and the controller are DMX compliant.
DESIGN LED 36 Pro™ Be sure to follow the above figure when making your own cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a short circuit and erratic behavior.
DESIGN LED 36 Pro™ terminator may avoid erratic behavior in your DMX line. A terminator is a 120 ohm 1/4 watt resistor that is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This fixture is inserted in the female XLR connector of the last fixture in your daisy chain to terminate the line. Using a line terminator (Elation part: DMX T PACK) will decrease the possibilities of erratic behavior. 5-Pin XLR DMX Connectors.
DESIGN LED 36 Pro™ setting the correct DMX address on the digital display located on the back of the fixture. You can set the same starting address for all fixtures or a group of fixtures, or set different address for each individual fixture. Be advised that setting all you fixtures to the same DMX address will subsequently control all fixtures in the same fashion, in other words, changing the settings of one channel will affect all the fixtures simultaneously.
DESIGN LED 36 Pro™ 8. FIXTURE MENU On-Board System Menu: The Design LED 36 Pro™ comes with an easy to navigate system menu. This next section will detail the functions of each command in the system menu. LED Control Panel: The control panel located on the base of the fixture allows you to access the main menu and make all necessary adjustments to the Design LED 36 Pro™. During normal operation, tapping the “MENU” key once will access the fixture’s main menu.
DESIGN LED 36 Pro™ MANL ~ tIME MOd1 /Mod2 OFF/HOLd/AUtO ON/OFF V-1.0~V-9.
DESIGN LED 36 Pro™ controller. “SLAV” - Slave setting for Master/Slave Operation With this function, you can define the device as slave for operation in Master/Slave mode. Each slave setting will have a different function for a dynamic lightshow without a controller. “rdMX” - Address via DMX - This function allows the DMX address to remotely be adjusted from a DMX console. This setting requires special settings for both the controller and the fixture. RDMX is on by default.
DESIGN LED 36 Pro™ visualization when the fixture is mounted in an inverted position. “d ON” – The display is designed to turn off during normal operation to avoid excessive light in situations that require an extremely dark environment. This function will adjust the time delay the fixture will remain on before it turns off. This function is disabled as default. 8.2 “SEt” – Fixture Personality Settings: These functions set specific running modes and operating parameters.
DESIGN LED 36 Pro™ 8.3 “MANL” – Manual Fixture Settings: This function allows the each of the six DMX channels to be controlled manually. This will allow the fixture to be preset to a specific color or built-in program without the use of a DMX console. 8.4 “tIME” – Operating Hours These functions will detail different time functions associated with the fixture. (0000~9999 Hours) This function tracks the running time of the fixture from the point it was last cleared.
DESIGN LED 36 Pro™ 8.5.2 Edit program – This function allows the user to edit the built-in programs. 8.5.3 Edit Scenes – This function allows the user to edit or define the actual scenes that are stored in the user defined built-in programs that are accessed in the previous step. 8.5.4 Rec Controller - The Design LED 36 Pro features an integrated DMX recorder. Pre-programmed scenes can be transmitted to the fixture via any DMX compliant controller.
DESIGN LED 36 Pro™ 9. DMX ADDRESSING Setting the DMX address - After the fixture is turned “ON” it will immediately complete a reset process that test all the fixture’s functions. When the reset process concludes the LCD will display the fixture’s current DMX. If the fixture is not receiving a DMX signal, the display will flash continuously. To set or adjust a DMX address, please follow the procedure below: 1. Toggle through the menu by pressing the Up and Down buttons until the display reads “Addr=XXX.
DESIGN LED 36 Pro™ 6. Press ENTER to confirm. 7. Press MODE/ESC to return to the main menu. Controller Settings: 1. Set the DMX value of channel 1 to a value of 7. 2. Set the DMX value of channel 2 to a value of 7 or 8. When channel 2 is set to "7" you can adjust the starting address between 1 and 255. When set to "8" you can adjust the starting address between 256 and 511. 3. Use channel 3 to set your desired DMX starting address.
DESIGN LED 36 Pro™ 10. OPERATION Operating Modes: The Design LED 36 Pro™ can operate in six different modes. This next section will detail the differences in the operating modes. • Auto Program Mode (Master) - The fixture will chase through the built-in programs, sending a DMX control signal to all other fixtures connect via DMX cables instruction for a synchronized light show. • Auto Program Mode (Stand-alone) - The fixture will chase through the built-in program.
DESIGN LED 36 Pro™ Control” submenu. See page 18 for the menu breakdown. Once in the “Music Control” submenu select “Alone” 10.2 Master/Slave Operation (Auto Program or Music Control): This function allows up to 16 fixtures to be linked together to provide a synchronized light show without the use of a controller. Only use this when linking several Design LED 36 Pro together for use without a controller. Any fixture can act as a “Master or a “Slave.
DESIGN LED 36 Pro™ 11. WORKING WITH BUILT-IN PROGRAMS The fixture comes equipped with a built-in DMX recorder that allows custom programs to be installed and recalled directly from the fixture’s control board. Programs can be created and stored using the fixture’s control board or by using an external DMX controller. The following instructions will detail the procedures for using the on-board system menu as well as using a DMX compliant controller.
DESIGN LED 36 Pro™ - “Green” – adjust the magenta flag value - “Blue” – adjust the yellow flag value - “Strobe” – adjust the strobe - “Dimmer” – adjust the dimmer intensity - “Scene Time” – set the hold time for the scene - “Input By Out” – this function will store a scene from an external DMX console. See the next section for scene editing via an external DMX controller. Step 1B – Building Scenes from an External DMX Controller The fixture includes a simple built-in DMX recorder.
DESIGN LED 36 Pro™ • To test the program access “Program Test” in the “Program Edit” menu function. Step 3 – Playing a Program To initiate a program follow the procedure below: • Access the main menu and use the “Up” and “Down” to toggle to “Function Mode” and tap the “Enter” button. • In the next screen select “Auto Program” and tap the “Enter” button. • There are now two selections, “Master” and “Alone.” Select “Master” when running multiple fixtures in a master/slave configuration.
DESIGN LED 36 Pro™ 12. DMX TRAITS DMX Operation Notes: The fixture will function in DMX mode whenever the unit is receiving a DMX signal. Please note that this will override all manual settings. This unit will keep and retain the last DMX command in the event of DMX signal failure. To reset the fixture you must turn the power off. DMX CHANNEL TRAITS The charts below and on the preceding pages outline the different DMX traits for the three different DMX modes.
DESIGN LED 36 Pro™ DMX channel’s functions and their values (3-Channel Mode): Channel 1 - Red: 0-255 Red (0-Black, 255 - 100% Red) Channel 2 - Green: 0-255 Green (0-Black, 255 - 100% Green) Channel 3 - Blue: 0-255 Blue (0-Black, 255 - 100% Blue) 4-Channel mode: In this mode channel one controls all the red LEDs, channel two controls all the green LEDs, channels three controls all the blue LEDs, and channel four-- will control the master dimming level.
DESIGN LED 36 Pro™ DMX channel’s functions and their values (4-Channel Mode): Channel 1 - Red: 0-255 Red (0-Black, 255 - 100% Red) Channel 2 - Green: 0-255 Green (0-Black, 255 - 100% Green) Channel 3 - Blue: 0-255 Blue (0-Black, 255 - 100% Blue) Channel 4 - Dimming 0-255 Dimming (0%-100%) ©Elation Professional, Los Angeles Ca. 33 www.ElationLighting.
DESIGN LED 36 Pro™ 6-Channel mode: In this mode channels 1~3 are used to control the RGB LEDs and channels 4~6 will control special features. 6-Channel Mode: The charts below and on the next page detail the DMX channel layout for 6-channel assignment.
DESIGN LED 36 Pro™ 161-190 Internal program 6 191-220 Internal program 7 221-255 Gradient Effect Channel 5 - Strobe: 0 Shutter Closed – LEDs Off 1~95 Strobe effect slow to fast 96-127 Shutter Open - LEDs On 128-159 Pulse effect in sequences 160-191 Shutter Open - LEDs On 192-223 Random strobe effect slow to fast 224-255 Shutter Open - LEDs On Channel 6 - General dimming / Program Speed Control This channel has two functions depending on the operating mode.
DESIGN LED 36 Pro™ 11. LENS REPLACEMENT The Design LED 36 Pro™ comes with a removable front cover that allows the lens assembly to be changed out to achieve different beam angles. The lens cover is held in place by four 5mm Allen screws. To access the lens kit, remove the bard door assembly (if so attached) to access the four 5mm Allen screws, then loosen the screws. The screws are held in by clips so they cannot be removed completely. Lift the outer cover to access the lens kit.
DESIGN LED 36 Pro™ 12. CLEANING AND MAINTENANCE Consider the following points during normal service and inspection: 1. Be sure all screws and fasteners are securely tightened at all times. Lose screws may fall out during normal operation resulting in damage or injury as larger parts could fall. 2. Electric power supply cables must not show any damage, material fatigue or sediments. Never remove the ground prong from the power cable.
DESIGN LED 36 Pro™ 13. A. 2-YEAR LIMITED WARRANTY Elation Professional® hereby warrants, to the original purchaser, Elation Professional® products to be free of manufacturing defects in material and workmanship for a period of two years, (730 days) from the date of purchase. This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories.
DESIGN LED 36 Pro™ effect. E. Elation Professional® reserves the right to make changes in design and/or improvements upon its products without any obligation to include these changes in any products theretofore manufactured. F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above.
DESIGN LED 36 Pro™ 14. PHOTOMETRIC DATA ©Elation Professional, Los Angeles Ca. 40 www.ElationLighting.
DESIGN LED 36 Pro™ ©Elation Professional, Los Angeles Ca. 41 www.ElationLighting.
DESIGN LED 36 Pro™ ©Elation Professional, Los Angeles Ca. 42 www.ElationLighting.
DESIGN LED 36 Pro™ 15. DIMENSIONAL DRAWINGS ©Elation Professional, Los Angeles Ca. 43 www.ElationLighting.
DESIGN LED 36 Pro™ 16. CIRCUIT SCHEMATIC ©Elation Professional, Los Angeles Ca. 44 www.ElationLighting.
DESIGN LED 36 Pro™ 17. TECHNICAL SPECIFICATIONS Power supply: 100v~240v / 50Hz~60Hz AC Power consumption: Maximum 150w LED Configuration: 36 x 3 Watt (12 x Red, 12 x Green 12 x Blue) Weight: 6 Kgs / 15.2Lbs DMX Channels: 6, 4, or 3 Channel mode DMX Drive: Standard DMX-512, 3-Pin XLR; [+] = Pin 3 [-] = Pin 2 [Ground] = Pin 1.
DESIGN LED 36 Pro™ ©Elation Professional, Los Angeles Ca. 46 www.ElationLighting.
Elation Professional 6122 S. Eastern Ave. Los Angeles, CA. 90040 323-582-3322 / 323-832-9142 fax www.ElationLighting.com / Info@ElationLighitng.com Rev. 10/04/2009 – visage Ver. 1.