Design LED 36 Pro Elation Professional™ 6122 S. Eastern Ave. Los Angeles, Ca 90040 www.elationlighting.com Rev.
DESIGN LED 36 Pro™ ©Elation Professional, Los Angeles Ca. 1 www.ElationLighting.
DESIGN LED 36 Pro™ TABLE OF CONTENS 1. General Information……………………………………………………………………… 3 a. Introduction………………………………………………………………………. 3 b. Unpacking………………………………………………………..…………..….. 3 c. Customer Support…………………………………………….………………… 3 d. Warranty Registration…………………………………………………………… 4 2. Safety Instructions………………………………………………………........…………. 5 3. Features…………………………………………………………………………………… 7 4. General Guidelines………………………………………………………………………. 8 5. Fixture Overview…………………………………………………………………………. 9 6.
DESIGN LED 36 Pro™ 1. GENERAL INFORMATION INTRODUCTION: Congratulations, you have just purchased one of the most innovative and reliable LED fixtures on the market today! The Design LED 36 Pro™ has been designed to perform reliably for years when the guidelines in this booklet are followed. Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this unit. These instructions contain important information regarding safety during use and maintenance.
DESIGN LED 36 Pro™ yourself. Doing so will void your manufactures warranty. Please do not discard the shipping carton in the trash. Please recycle whenever possible. WARRANTY REGISTRATION: The Design LED 36 Pro™ carries a two year (730 days) limited warranty. Please fill out the enclosed warranty card to validate your purchase. All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number. The R.A.
DESIGN LED 36 Pro™ 2. SAFETY INSTRUCTIONS To guarantee proper and consistent operation, it is important to follow the guidelines in this manual. Elation Professional will not accept responsibility for damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual. 1. To reduce the risk of fire or shock, do not expose this fixture to rain or moisture.
DESIGN LED 36 Pro™ 11. Qualified personnel should perform all electrical connections. 12. Be sure the available voltage matches the voltage requirements of the unit. Be sure the power cord is never crimped or damaged. If the power cord is damaged, replace it immediately with a new one of similar power rating. 13. Always disconnect from main power before performing any type of service or any cleaning procedure. 14. Only handle the power cord by the plug.
DESIGN LED 36 Pro™ 3.
DESIGN LED 36 Pro™ 4. GENERAL GUIDELINES This fixture is a professional lighting effect designed for use on stage, in nightclubs, in theatres, and other types of architectural installations. Do not attempt operation or installation without a proper knowledge on how to do so. This fixture was designed for indoor use only; use of this fixture outside will void the manufacture’s warranty. Consistent operational breaks will ensure that the fixture will function properly for many years to come.
DESIGN LED 36 Pro™ 5. FIXTURE OVERVIEW 1. LED Lens Assembly – The lens assembly may be user replaced in the event repair is needed or a different beam angle is required. ©Elation Professional, Los Angeles Ca. 9 www.ElationLighting.
DESIGN LED 36 Pro™ 2. LED Display – 4-segment menu display. Used to display the DMX address as well as all other menu functions. 3. Power Output Lead – This lead is used to jump power to another Design LED 36 Pro™. Please do not daisy-chain power for more than 16 fixtures. 4. DMX Out Lead – XLR female lead. This lead is used to send an incoming DMX signal to the next fixture in the DMX chain. 5. Menu Button – This button is used to access the fixtures menu functions. 6.
DESIGN LED 36 Pro™ For added protection mount the fixtures in areas outside walking paths, seating areas, and away from areas were unauthorized personnel might reach the fixture. Before mounting the fixture to any surface, make sure that the installation area can hold a minimum point load of 10 times the device’s weight. Fixture installation must always be secured with a secondary safety attachment, such as an appropriate safety cable.
DESIGN LED 36 Pro™ Mounting The Design LED 36 Pro™ is fully operational in any mounting position, hanging upside-down, side mounted, or set on a flat level surface, etc. Be sure this fixture is kept at least 0.5m (1.5 feet) away from any flammable materials (decoration etc.). When clamp mounting; always use and install the supplied safety cable as an added safety measure to prevent accidental damage in the event of a clamp failure. See the image below.
DESIGN LED 36 Pro™ added safety measure be sure to attach at least one properly rated safety cable to the fixture. See illustrations below. Securing the Design LED 36 Pro™ Always be sure to secure your fixture with a safety cable when suspending the unit from truss or other means. The fixture provides a built-in rigging point for a safety cable as illustrated above. Be sure to only use the designated rigging point for the safety cable and never secure a safety cable to the hanging bracket.
DESIGN LED 36 Pro™ 7. UNDERSTANDING DMX DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by most lighting and controller manufactures as a form of communication between intelligent fixtures and controllers. DMX allows all makes and models of different manufactures to be linked together and operate from a single controller. This is possible as long as all the fixtures and the controller are DMX compliant.
DESIGN LED 36 Pro™ DMX-512 connection with DMX terminator A DMX terminator should be used in all DMX lines especially in longer runs. The use of a terminator may avoid erratic behavior in your DMX line. A terminator is a 120 ohm 1/4 watt resistor that is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This fixture is inserted in the female XLR connector of the last fixture in your daisy chain to terminate the line.
DESIGN LED 36 Pro™ correct fixture responds to the correct control signal. This digital starting address is the channel number from which the fixture starts to “listen” to the digital control information sent out from the DMX controller. The allocation of this starting DMX address is achieved by setting the correct DMX address on the digital display located on the back of the fixture.
DESIGN LED 36 Pro™ 8. DISPLAY LED INDICATORS. The Design LED 36 Pro ™ has two LED indicators on the display. These indicators are designed to give a quick visual indication of the fixtures’ status. The illustration below details the functionality of the LED indicators. . . DMX OK . .
DESIGN LED 36 Pro™ 9. DISPLAY MENU Default settings shaded. MODE ADDR DISP FLIP CHAN SLAV CNTL MANU BLAC Set the starting DMX address Display “Blackout” function. When activated the ON/OFF display will automatically blackout when not in use.
DESIGN LED 36 Pro™ CHS5 CHS6 CHS7 CHS8 OTHR DIMR FADE XXX Adjust program 4 fade time STRB XXX Adjust strobe rate of program 4 SPED XXX Adjust program 5 speed FADE XXX Adjust program 5 fade time STRB XXX Adjust strobe rate of program 5 SPED XXX Adjust program 6 speed FADE XXX Adjust program 6 fade time STRB XXX Adjust strobe rate of program 6 SPED XXX Adjust program 7 speed FADE XXX Adjust program 7 fade time STRB XXX Adjust strobe rate of program 7 SPED XXX Adjust p
DESIGN LED 36 Pro™ 10. DMX TRAITS DMX Operation Notes: The fixture will function in DMX mode whenever the unit is receiving a DMX signal. Please note that this will override all manual settings. This unit will keep and retain the last DMX command in the event of DMX signal failure. To reset the fixture you must turn the power off. DMX CHANNEL TRAITS The charts below and on the preceding pages outline the different DMX traits for the three different DMX modes.
DESIGN LED 36 Pro™ DMX channel’s functions and their values (3-Channel Mode): Channel 1 - Red: 0-255 Red (0-Black, 255 - 100% Red) Channel 2 - Green: 0-255 Green (0-Black, 255 - 100% Green) Channel 3 - Blue: 0-255 Blue (0-Black, 255 - 100% Blue) 4-Channel mode: In this mode channel one controls all the red LEDs, channel two controls all the green LEDs, channels three controls all the blue LEDs, and channel four-- will control the master dimming level.
DESIGN LED 36 Pro™ DMX channel’s functions and their values (4-Channel Mode): Channel 1 - Red: 0-255 Red (0-Black, 255 - 100% Red) Channel 2 - Green: 0-255 Green (0-Black, 255 - 100% Green) Channel 3 - Blue: 0-255 Blue (0-Black, 255 - 100% Blue) Channel 4 - Dimming / Program Speed Control This channel has two functions depending on the operating mode. When running the built-in programs this channel will control the program speed.
DESIGN LED 36 Pro™ DMX channel’s functions and their values (6-Channel Mode): Channel 1 - Red: 0-255 Red (0-Black, 255-100% Red) Channel 2 - Green: 0-255 Green (0-Black, 255- 100% Green) Channel 3 - Blue: 0-255 Blue (0-Black, 255- 100% Blue) Channel 4 - Internal programs: 0-10 No function 11-40 Internal program 1 41-70 Internal program 2 71-100 Internal program 3 101-130 Internal program 4 131-160 Internal program 5 161-190 Internal program 6 191-220 Internal program 7 221-255 Internal progra
DESIGN LED 36 Pro™ Channel 6 - General dimming / Program Speed Control This channel has two functions depending on the operating mode. When running the built-in programs this channel will control the program speed, when not running the built-in programs this channel will control master dimming. 0-255 Dimming (0%-100%) ~ Normal Operation 0-255 Speed (min to max) ~ When running built-in programs on channel 4 ©Elation Professional, Los Angeles Ca. 24 www.ElationLighting.
DESIGN LED 36 Pro™ 11. LENS REPLACEMENT The Design LED 36 Pro comes with a removable front cover that allows the lens assembly to be changed out to achieve different beam angles. The lens cover is held in place by four 5mm Allen screws. To access the lens kit, remove the bard door assembly (if so attached) to access the four 5mm Allen screws, then loosen the screws. The screws are held in by clips so they cannot be removed completely. Lift the outer cover to access the lens kit.
DESIGN LED 36 Pro™ 12. CLEANING AND MAINTENANCE Consider the following points during normal service and inspection: 1. Be sure all screws and fasteners are securely tightened at all times. Lose screws may fall out during normal operation resulting in damage or injury as larger parts could fall. 2. Electric power supply cables must not show any damage, material fatigue or sediments. Never remove the ground prong from the power cable.
DESIGN LED 36 Pro™ 13. A. 2-YEAR LIMITED WARRANTY Elation Professional® hereby warrants, to the original purchaser, Elation Professional® products to be free of manufacturing defects in material and workmanship for a period of two years, (730 days) from the date of purchase. This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories.
DESIGN LED 36 Pro™ effect. E. Elation Professional® reserves the right to make changes in design and/or improvements upon its products without any obligation to include these changes in any products theretofore manufactured. F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above.
DESIGN LED 36 Pro™ 14. PHOTOMETRIC DATA ©Elation Professional, Los Angeles Ca. 29 www.ElationLighting.
DESIGN LED 36 Pro™ ©Elation Professional, Los Angeles Ca. 30 www.ElationLighting.
DESIGN LED 36 Pro™ ©Elation Professional, Los Angeles Ca. 31 www.ElationLighting.
DESIGN LED 36 Pro™ 15. DIMENSIONAL DRAWINGS ©Elation Professional, Los Angeles Ca. 32 www.ElationLighting.
DESIGN LED 36 Pro™ 16. CIRCUIT SCHEMATIC ©Elation Professional, Los Angeles Ca. 33 www.ElationLighting.
DESIGN LED 36 Pro™ 17. TECHNICAL SPECIFICATIONS Power supply: 100v~240v / 50Hz~60Hz AC Power consumption: Maximum 150w LED Configuration: 36 x 3 Watt (12 x Red, 12 x Green 12 x Blue) Weight: 6 Kgs / 15.2Lbs DMX Channels: 6, 4, or 3 Channel mode DMX Drive: Standard DMX-512, 3-Pin XLR; [+] = Pin 3 [-] = Pin 2 [Ground] = Pin 1.
Elation Professional 6122 S. Eastern Ave. Los Angeles, CA. 90040 323-582-3322 / 323-832-9142 fax www.ElationLighting.com / Info@ElationLighitng.com Rev.
