POWER SPOT 700CMY User Manual Revised 4/4/2007 visage
Power Spot 700CMY™ ©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.
Power Spot 700CMY™ Table of Contents Introduction...........................................................................................................................4 Unpacking ....................................................................................................................4 Customer Support ......................................................................................................4 Discharge Lamp Precautions .............................................................
Power Spot 700CMY™ INTRODUCTION: Congratulations, you have just purchased one of the most innovative and reliable lighting fixtures on the market today! The Power Spot 700CMY™, has been designed to perform reliably for years when the guidelines in this booklet are followed. Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this unit. These instructions contain important information regarding safety during use and maintenance.
Power Spot 700CMY™ WARRANTY REGISTRATION: The Power Spot 700CMY™ carries a two year (730 days) limited warranty. Please fill out the enclosed warranty card to validate your purchase. All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number. The R.A. number must be clearly written on the outside of the return package. A brief description of the problem as well a s the R.A.
Power Spot 700CMY™ their recommended duty cycle. Extreme caution should be used when operated this or any fixture fitted with a gas discharge lamp. Never open this fixture while in use! During the initial operation of this fixture, a light smoke or smell may emit from the interior of the fixture. This is a normal process and is caused by excess paint in the interior of the casing burning off from the heat associated with the lamp. This device falls under protection-class 1.
Power Spot 700CMY™ 2. SAFETY INSTRUCTIONS The Power Spot 700CMY™ is an extremely sophisticated piece of electronic equipment. To guarantee a smooth operation, it i s important to follow the guidelines in this manual. The manufacturer of this device will not accept responsibility for damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual. 1. Always be sure that the fan and the air inlets remain clean and are never blocked.
Power Spot 700CMY™ 3.
Power Spot 700CMY™ 4. GENERAL GUIDELINES This fixture is a professional lighting effect designed for use on stage, in nightclubs, in theatres, etc. Do not attempt operation or installation without a proper knowledge on how to so. This fixture was designed for indoor use only. Consistent operational breaks may ensure that the fixture will function properly for many years to come. Do not shake the fixture around. Avoid brute force when installing or operating the device.
Power Spot 700CMY™ Transportation and Handling The POWER SPOT 700CMY™ comes with two carrying handles built into the base. Always transport the fixture by these handles. Never lift or carry the POWER SPOT 700CMY™ by the yoke (head assembly) this can seriously damage the unit and will void your manufactures warranty. Connections Power supply: Electronic ballast with: 90~260 Volts, 50~60 Hz, Grounded contact type plug – Neutrik Powercon Connected load 1000W <=> 4.5 A (blind current compensation).
Power Spot 700CMY™ 5. FIXTURE LAYOUT 1. Moving Head 2. Carrying Handles 3. LED Menu Display 4. Head Tilt Lock 5. Omega Clamp 8 6 . Software-Update Connector 9 DMX IN 7 . Microphone Sensitivity 15 2 DMX OUT 1.Ground 2.Data 3.Data + Min Max Mic Sensiti vity Software Update 8. DMX- Input 9. DMX- Output 7 10 6 10. Fan (air inlet/outlet) 10 15 2 13 12. Main Power Supply (Powercon) 14 POWER 0 13. Power On/Off 1 Lamp Fuse T 10A @ 115 V~ T 5A @ 230 V~ 11.
Power Spot 700CMY™ Side View - Menu and Display 15. 4-Segment LED Menu Display 15 16. Mode Button 16 17 18 19 17. Enter Button 18. Up Button 19. Down Button 1. Head Assembly – The head assembly consist of the main output lens, and either the standard or CMY control module. 2. Carrying Handle – The fixtures includes two built-in carrying handles. Be sure to always handle the fixture by the built-in carrying handles.
Power Spot 700CMY™ attach a clamp that is rated to handle the weight of the unit to your omega clamp. After a clamp has been attached to the omega clamp, attach the cam locks to the designated position on the bottom of your unit. Lock the cam locks into position by turning the wing nuts 90°. See page XX for proper clamp mounting and assembly. 6. Firmware Connection – This connector is for use by an authorized technician only. This connector is used to upgrade the operating software and to test the fixture.
Power Spot 700CMY™ 12. Powercon Connector – This power jack is designed to be used only with the Neutrik Powercon adapter included with your fixture. This jack provides main power to your fixture. 13. Power Switch – The switch is used to control main power to fixture’s electronics. 14. Lamp Fuse Holder – This housing holds a 250v/10A GMA fuse (120v operation). Never defeat this fuse. This fuse is designed to protect the lamp in the event of severer power fluctuations.
Power Spot 700CMY™ 6. MOUNTING AND INSTALLATION MOUNTING The POWER SPOT 700CMY™ is fully operational in two different mounting positions, hanging upside from a ceiling or set on a flat level surface. To avoid internal damage to the unit, never mount the unit on its side as illustrated below. Be sure this fixture is kept at least 0.5m away from any flammable materials (decoration etc.). Install a safety cable that can hold at least 10 times the weight of the fixture.
Power Spot 700CMY™ periodic safety inspection of all installation material and the fixture. If you lack these qualifications, do not attempt the installation yourself. Improper installation can result in bodily injury. CAUTION! Be sure a qualified electrician performs all electrical connections. Be sure to complete all rigging and installation procedures before connecting the main power cord to the appropriate wall outlet.
Power Spot 700CMY™ Secure the POWER SPOT 700CMY™ Regardless of the rigging option you choose for your POWER SPOT 700CMY™ always be sure to secure your fixture with a safety cable. The fixture provides a built-in rigging point for a safety cable on the underside of the fixture, be sure to use this point and never secure a safety cable to a carrying handle. ©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.
Power Spot 700CMY™ 7. UNDERSTANDING DMX DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by most lighting and controller manufactures as a form of communication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions from the controller to the fixture.
Power Spot 700CMY™ Notice: Be sure to follow the figure on the previous page when making your own cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a short circuit and erratic behavior.
Power Spot 700CMY™ 5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR connectors for DATA transmission in place of 3-pin. 5-pin XLR fixtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be used, these adaptors are readily available at most electric stores. The chart below details a proper cable conversion.
Power Spot 700CMY™ selected fixture. In the case of the Power Spot 700CMY™, which is a 24 channel fixture, you should set the starting DMX address of the first unit to 1, the second unit to 25 (24 + 1), the third unit to 49 (24 + 25), and so on. Note: During start-up the Power Spot 700CMY™, will automatically detect whether a DMX data signal is being received or not. If DMX data signal is being received, the display will show "A.XXX" (XXX representing the actual DMX address).
Power Spot 700CMY™ 8.
Power Spot 700CMY™ CL1f GOB1 GOB2 SHSC SHOC FR U FR O PRIS IRIS FOCU POFS TOFS CLRE SPFS ARES DFSE FEED EFLG Fine calibration of color wheel 1 (CTO) Calibration of gobo wheel 1 Calibration of gobo wheel 2 Shutter moves pair wise open and close Shutter moves pair wise parallel left and right Calibration of frost filter A Calibration of frost filter b Calibration of prism wheel Calibration of iris Calibration of focus Calibration of Pan-Offsets Calibration of Tilt-Offsets Settings in the internal memory (sup
Power Spot 700CMY™ The DMX address is non-destructible and will remain in the fixture’s memory even when the power has been switched off. Memory is backed-up and retained by an internal power source with a five year shelf life. 8.2 Test Program Test The Test Program engages the fixture’s internal test mode. This function runs a complete test procedure of all functions. Press Enter to launch the self-test or the Mode button to cancel and return to the main menu. 8.
Power Spot 700CMY™ This function allows you to manually control the lamp operation. Access the lamp function in the main menu and use the use the Up and Down buttons to toggle between lamp On and lamp Off. Press the Enter button to confirm the operation or the Mode button to cancel and return to the main menu. (The lamp OFF command will only functions if and when the shutter is closed at the same time). 8.5 Reset RESE This function will rest and return all motors to the home position.
Power Spot 700CMY™ 8.8 Invert Tilt Movement RTLT This function allows you to invert all tilt movements. Use the Up and Down buttons to turn this function On and Off. Press the Enter button to accept the change or the Mode button to cancel and return to the main menu. 8.9 DMX Mode DMOD This function allows you to toggle between 16bit (default mode) and 8bit mode. 16bit will activate the pan fine and tilt fine DMX channels for a total of 24 DMX channels.
Power Spot 700CMY™ lock in your value. Use the Mode button to cancel at any time.
Power Spot 700CMY™ 8.10.3 Lamp Off via DMX DLOF This function allows the lamp to be switched off through a DMX controller. To enable this function use the Up and Down buttons to toggle between ON and Off. Turn this function “ON” to allow DMX switching. Use the Enter button to accept your selection or the Mode button to cancel and return to the menu. 8.10.4 DMX Input DMXI This function will display the DMX value of a channel in the LED as the fixture receives it.
Power Spot 700CMY™ EFFR SPEC MOVE SPED 000 _ 255 000 _ 255 000 _ 255 000 _ 255 Effect wheel rotation Lamp Off, Reset, ... Movement Speed for Pan/Tilt 8.10.5 Display DISP Use this function to choose between different display indications. Use the Up/Down-keys to select desired function and press Enter to confirm or Mode to cancel and return to the menu. D ON Display On/Off (If you've chosen off, the display will go out within 15 seconds after the last input.
Power Spot 700CMY™ FANS By using this function you can choose between 4 types of fan speed operations. Use the Up and Down buttons to select the desired fan setting, then press Enter to accept your setting or press the Mode button to cancel and return to the menu. The chart below will detail the different fan settings: HIGH The cooling fan works continuously at max. speed. REG This is the default fan setting.
Power Spot 700CMY™ 8.10.9 Adjustments and Calibrations ADJU With this function you can adjust and calibrate the positions of the different wheels and other motors. This feature is reserved for a service technician and is sometimes required after a service or repair work. This function requires a service code only available to authorized service technicians.
Power Spot 700CMY™ 8.10.10 Default Settings DFSE This function is used to restore all the factory default settings and presets. Press the Enter button to confirm this operation or the Mode button to cancel and return to the menu. When this operation is selected the LED will briefly readout ok, then return to the previous function. The chart below details the factory defaults.
Power Spot 700CMY™ Display Error and Information Messages HEAt This message appears if you try to switch on the lamp within 5 minutes after having switched off (lamp too hot). The message will appear on the display if the lamp doesn’t ignite within 20 seconds. The fixture will store this command and automatically ignite the lamp after 5 minutes. IG E When igniting the lamp, the electronic ballast will examine whether the lamp ignited or not.
Power Spot 700CMY™ 9. OPERATION Operating Modes: The Power Spot 700CMY™ can operate in three different modes. This next section will detail the differences in the operating modes. • Stand alone mode - The fixture will react to sound, chasing through the built-in programs. • Master/Slave mode - You can daisy chain up to 16 fixtures together to get a synchronized light show without the need of an external controller. The fixtures will react to sound chasing to synchronized light show.
Power Spot 700CMY™ to the audio submenu. See page 16 for the menu breakdown. 9.2.3 In the audio submenu choose the audio chase speed, fast or slow. Slow (ASLW) will trigger the chase sequence to every two beats, while fast (AFST) will trigger the chase impulse every beat. See page 16 for more details. 9.2.4 Be sure the Master (MSTR) function is switched “ON,“ and the SVPT function i s switched “OFF.“ 9.2.5 Choose your room size.
Power Spot 700CMY™ 10. DMX CHANNEL SELECTION (DMX PROTOCOL) Channel Function Time and Value DMX HEX % 1) Pan 0..530° Min. 2.65 s 0..255 00..FF 0..100 2) Pan-fine High-Pos ... High-Pos + 2.1° (16 Bit) 0..255 00..FF 0..100 3) Tilt 0..285° 0..255 00..FF 0..100 4) Tilt-fine High- Pos … High- Pos + 1.1° (16 Bit) 0..255 00..FF 0..100 5) Color 1 Open (fast) 00..01 0.2 (fast) Open / Color 1 (fast) 02..03 1.0 Color 1. Lila 509 (fast) Chaser from color to 0..1 color max.
Power Spot 700CMY™ Channel Function Time and Value DMX HEX % Color 4. Orange 306u (slow) 80..81 50..51 31.6 Color 4 / Color 5 (slow) 82..83 52..53 32.4 Color 5. Lila 502 (slow) 84..85 54..55 33.1 Color 5 / Color 6 (slow) 86..87 56..57 33.9 Color 6. Yellow 601 (slow) 88..89 58..59 34.7 Color 6 / Color 7 (slow) 90..91 5A..5B 35.5 Color 7. CTC 3200 - 4100 (slow) 92..93 5C..5D 36.3 Color 7 / Color 8 (slow) 94..95 5E..5F 37.1 Color 8. Rot 308 (slow) 96..97 60..61 37.
Power Spot 700CMY™ Channel Function Time and Value DMX HEX % Gobo 4 (slow) 88..95 58..5F 34..36. 9 Gobo 5 (slow) 96..103 60..67 37..39. 9 Gobo 6 (slow) 104..111 68..6F 40..42. 9 Gobo 7 (slow) 112..119 70..77 43..45. 9 Gobo 8 (slow) 120..127 78..7F 46..49 Gobo rotation STOP 128..129 80..81 50 51..75 Gobo rotation, slow-fast, CW Min. 1.4 turns/h 130..191 82..BF Gobo rotation, fast-slow, CCW Max. 1.0 turns/sec. 192..253 C0..FD 76..
Power Spot 700CMY™ Channel 12) Shutter Function Time and Value DMX HEX % Gobo 5 (slow) 80..83 51..53 32..33 Gobo 6 (slow) 84..87 54..57 33..34 Gobo 7 (slow) 88..91 58..5B 35..36 Gobo 8 (slow) 92..95 5C..5F 36..37 Gobo 9 (slow) 96..99 60..63 38..39 Gobo 10 (slow) 100..103 64..67 39..40 Gobo rotation STOP 128..129 80..81 50 51..75 Gobo rotation, slow-fast, CW Min. 1.4 turns/h 130..191 82..BF Gobo rotation, fast-slow, CCW Max. 1.0 turns/sec. 192..253 C0..FD 76..
Power Spot 700CMY™ Channel Function Time and Value DMX HEX % Ascend with Shutter, audio 160..175 A0..AF 63..68 Descend with Shutter, audio 176..191 B0..BF 69..74 Ascend with Shutter Slow - fast 192..207 C0..CF 75..81 Descend with Shutter Slow - fast 208..223 D0..DF 82..87 Pulse - effect Slow - fast 224..239 E0..EF 88..93 Ascend - descend effect Slow - fast 240..253 F0..FD 94..99 254..255 FE..FF 100 0 - 100% 0..255 00..FF 0..
Power Spot 700CMY™ Channel Function DMX HEX % ment Movement Size Phase PAN 1 0° 01..01 01..01 0.5 1 90° 02..03 02..03 1.0 1 180° 04..05 04..05 1.7 1 270° 06..07 06..07 2.5 2 0° 08..09 08..09 3.3 2 90° 10..11 0A..0B 4.1 2 180° 12..13 0C..0D 4.9 2 270° 14..15 0E..0F 5.7 3 0° 16..17 11..11 6.5 3 90° 18..19 12..13 7.3 3 180° 20..21 14..15 8.0 3 270° 22..23 16..17 8.8 4 0° 24..25 18..19 9.6 4 90° 26..27 1A..1B 10.4 4 180° 28..29 1C.
Power Spot 700CMY™ Channel 22 Reset ©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com 250..25 FA..FF 98..
Power Spot 700CMY™ 11. LAMP REPLACEMENT For a proper and safe lamp change, please read this chapter carefully and follow all instructions. Safety Regulations • Pull out the main plug! • Wait min. 20 minutes after the last operation to cool down the fixture. • Don’t touch the bulb of the lamp with bare fingers (this can cause damages. • Before you put the POWER SPOT 700CMY™ into operation close the casing, otherwise your retina can be hurt! • Replace the lamp with an approved replacement type.
Power Spot 700CMY™ 4. Using a standard flat head screwdriver release 1/4 turn quick-lock fasteners (labeled 1, 2, 3, and 4) of the backside lamp sheet and remove it carefully. These fasteners will remain connected to the lamp socket cover. 5. Gently remove the old lamp from it’s socket. If the old lamp has exploded be sure to remove all of the old lamp fragments to prevent damage to the internal components. 6. Insert the new lamp securely, locking the lamp in place as illustrated in the diagram to the left.
Power Spot 700CMY™ 1. Using a flathead screwdriver move the lamp position with setscrew “B” forwards and backwards until a very bright luminous spot (hotspot) can been seen clearly. 2. Move lamp with setscrew “A” upward/downwards until this hotspot is in the center of the beam projection. 3. Use setscrew “B” once again to move the lamp forwards and backwards until you've reached the most even beam projection. Note: A slight hotspot will always remain and is conditional to the optical path.
Power Spot 700CMY™ 12. FUSE REPLACEMENT Caution: Always replace with the exact same type fuse, unless otherwise specified by an authorized Elation® service technician. Replacing with anything other than the specified part can damage your unit and will void your manufactures warranty. Warning: If you continue to blow fuses, STOP using the fixture. Contact customer support for further instructions, you may have to return the unit for servicing. Continuing to use the unit may cause serious damage.
Power Spot 700CMY™ 13. OPTICAL EFFECTS MODULE The Power Spot 700CMY is equipped with an optical effects module that can be easily removed for cleaning, service, and gobo/color exchange. Please follow the procedures below for proper removal and service of the effects module. 13.1 Safety considerations 13.2 • Always remove main power before attempting any type of service procedure.
Power Spot 700CMY™ Data Bus 2x 4) Loosen the two locking thumbscrews on the left and right side of the optical effects module (please do not attempt to remove the thumbscrews completely). Once the thumbscrews have been loosened push them inwards towards the center of the head while gently pulling the effects module straight out. You may use the metal support plates to grasp and pull the effects module out. See the illustration below; Attention: The effects module reset between two lateral tracks.
Power Spot 700CMY™ remove the module. Use the metal support plates or the stepper motors as a means to grasp the module. 5) To access the internal components of the module loosen the three securing thumbscrews illustrated below. Once these screws are lose you may place the module on a flat and open the unit up as if it were a book. This will allow access the all the gobos and colors so they me be changed or cleaned. 1 2 3 6) For Gobo and Color replacement please see the next section.
Power Spot 700CMY™ 14. CHANGING/REPLACING GOBOS/COLORS Before attempting to change any gobos or color be sure to follow the effects module removal process as described in the previous section (section 13) of this manual. The POWER SPOT 700CMY includes both Aluminum (thickness = 0.3 mm) and Glass (thickness = 1.1 - 3.0 mm) gobos (outside diameter 26.9 mm, viewable image size 23 mm). There is one rotating Gobos wheel (user replaceable gobos) and one fixed Gobo wheel (non replaceable gobos). 14.
Power Spot 700CMY™ Attention: Custom gobos that contain company logos and text must also be orientated properly to ensure proper display of the custom image. The readable side must be mounted towards the lamp. In the illustration below, notice that the text is readable in the example on the left and mirrored in the example on right. The illustration below details proper gobo placement.
Power Spot 700CMY™ 2) Genteelly lift and pull the gobo holder out of the center part of the wheel hub to remove the individual holder. See the left image below. 3) Once the gobo holder has been removed the Gobo itself can be replaced by remove the centric spring with a small screwdriver or gripping pliers. Be sure to follow the gobo alignment instructions that are detailed on the previous page of this manual (section 14.1).
Power Spot 700CMY™ Failure to do so may result in damage to the color filter. 8 OPEN 1 7 29.8mm Magnet 6 2 3 5 4 Gobo wheel 1 with rotating Gobos ©Elation Professionals® Los Angeles, Ca. Gobo wheel 2 with fixed Gobos - wwww.ElationLighting.
Power Spot 700CMY™ 15. CHANGING ANIMATION WHEEL The Power Spot 700CMY is equipped with an animation wheel that can simulate effects such as running water, fire, clouds, and others. The unit ships with the fire effect wheel already installed. Four optional wheels are included in the accessory pack. Follow the procedures outlined below for proper effects wheel exchange: 15.1 Safety considerations: • Always remove main power before attempting any type of service procedure.
Power Spot 700CMY™ thumbscrew holds an angled aluminum bar in place. 2 15.2.4 Fold the angled bar out of the way and pull the animation wheel up and out of the optical path. Once the animation wheel is exposed it can be exchanged with the use of any tools. 15.2.5 The wheel itself is magnetically mounted on the wheel axis and i s removed by simply pulling it away from wheels center hub. Be sure to grasp the wheel from as close to the hub as possible, this will prevent the wheel from bending.
Power Spot 700CMY™ 15.2.6 After the animation wheel is exchanged resemble the fixture in reverse order. Be sure the effects wheel is completely seated on the magnetic axis hub and that all screws are fastened completely before attempting operation. Effect wheel insertion and spares: 25-022-1102 STANDARD 25-022-1094 Optional ©Elation Professionals® Los Angeles, Ca. 25-022-1096 Optional - wwww.ElationLighting.
Power Spot 700CMY™ 25-022-1098 Optional ©Elation Professionals® Los Angeles, Ca. 25-022-1095 Optional - wwww.ElationLighting.
Power Spot 700CMY™ 16. MAINTENANCE AND CLEANING THE POWER SPOT 700CMY™ It is absolutely essential that the fixture is kept clean and dust, dirt and smoke-fluid residues do not built-up on the surface or within the fixture. Residue build-up may cause the fixture's light output to be significantly reduced. Regular cleaning will not only ensure the maximum light output, but will also allow the fixture to function reliable throughout its life.
Power Spot 700CMY™ Prism Monthly Soft cloth and glass cleaner Dimmer/Shutter Yearly Vacuum cleaner, airbrush, etc. Inside lens Monthly Soft cloth no glass cleaner Fan and air channel Monthly Vacuum cleaner, airbrush, etc. Reflector Never Lamp Never Moveable parts Yearly Suitable Lubricant Caution: 1. Never allow the optical parts to come in contact with oil, dirt, or grime. 2. Allow all parts to dry completely before attempt operation. 3.
Power Spot 700CMY™ 17. TWO YEAR (730 DAYS) LIMITED WARRANTY A. Elation Professionals® hereby warrants, to the original purchaser, Elation Professionals® products to be free of manufacturing defects in material and workmanship for a period of two years (730 days) from the date of purchase. This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories.
Power Spot 700CMY™ F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above. Except to the extent prohibited by applicable law, all implied warranties made by Elation Professionals® in connection with this product, including warranties of merchantability or fitness, are limited in duration to the warranty period set forth above.
Power Spot 700CMY™ 18. PHOTOMETRIC DATA ©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.
Power Spot 700CMY™ 19. DIMENSIONS ©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.