w w w . e l a t i o n l i g h t i n g . c o m user manual 1.0 1 CUEPIX BLINDER WW2™ User Manual 1.0 E L A TI ON | CUEPIX BLINDER WW2™ | user manual 1.
w w w . e l a t i o n l i g h t i n g . c o m ©2013 by ELATION PROFESSIONAL. All Rights Reserved. Information, specifications, diagrams, images, and instructions herein are subject to change without notice. ELATION PROFESSIONAL logo and identifying product names and numbers herein are trademarks of ELATION PROFESSIONAL. Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted.
w w w . e l a t i o n l i g h t i n g . c o m GENERAL INFORMATION INTRODUCTION Congratulations, you have just purchased one of the most innovative and reliable lighting fixtures on the market today! The CUEPIX BLINDER WW2™ has been designed to perform reliably for years when the guidelines in this booklet are followed. Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this unit.
w w w . e l a t i o n l i g h t i n g . c o m CUSTOMER SUPPORT Elation Professional® provides a customer support line, to provide set up help and to answer any question should you encounter problems during your set up or initial operation. You may also visit us on the web at www.elationlighting.com for any comments or suggestions. For service related issue please contact Elation Professional®. Service Hours are Monday through Friday 8:00 a.m. to 5:00 p.m. PST.
w w w . e l a t i o n l i g h t i n g . c o m 2-YEAR LIMITED WARRANTY A. Elation Professional® hereby warrants, to the original purchaser, Elation Professional® products to be free of manufacturing defects in material and workmanship for a period of two years, (730 days) from the date of purchase. This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories.
w w w . e l a t i o n l i g h t i n g . c o m SAFETY INSTRUCTIONS The CUEPIX BLINDER WW2™ is an extremely sophisticated piece of electronic equipment. To guarantee a smooth operation, it is important to follow the guidelines in this manual. The manufacturer of this device will not accept responsibility for damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual. This device falls under PROTECTION CLASS 1.
w w w . e l a t i o n l i g h t i n g . c o m SAFETY INSTRUCTIONS - CONTINUED Always disconnect from main power source before performing any type of service and/or cleaning • procedure. Only handle the power cord by the plug end, never pull out the plug by tugging the wire portion of the cord. Do not operate this fixture if the power cord has become frayed, crimped and/or damaged. If the power • cord is damaged, replace it immediately with a new one of similar power rating.
w w w . e l a t i o n l i g h t i n g . c o m FIXTURE OVERVIEW 1. 5pin DMX IN – Accepts incoming DMX signal via a male 5pin XLR jack. 2. 3pin DMX IN – Accepts incoming DMX signal via a male 3pin XLR jack. 3. Fuse - Fuse holder. 4. powerCON IN – Power connection to power source. 5. powerCON OUT - Power link connection to next unit. 6. 3pin DMX OUT – Sends DMX signal to next fixture in chain via a female 3pin XLR jack. 7.
w w w . e l a t i o n l i g h t i n g . c o m INSTALLATION T he el ec tri c c onnec ti on m ust onl y b e c arri ed out b y a qu al if i ed el ec tri c i an. CAUTIONS The recommended temperature for this fixture is 14°F to 113°F (-10°C to 45°C). • Do not use the fixture under or above this temperature. For added protection, mount the fixture in areas outside walking paths, seating areas, or in areas were • unauthorized personnel might reach the fixture.
w w w . e l a t i o n l i g h t i n g . c o m FIXTURE MENU OPERATING INSTRUCTIONS 1) MANUAL DIMMING / FLASH 2) SETTING PIXEL FLIP 3) SETTING DIMMER CURVES 4) MASTER / SLAVE MODES 5) DMX MODE When the display flashes, you can select the desired mode via the UP/DOWN buttons. The display will shut off and lockout after 30 seconds of no use. Press and hold MODE button for approx. 10 seconds to unlock display.
w w w . e l a t i o n l i g h t i n g . c o m PIXEL FLIP SETTING: Select the desired starting COB module and chase direction from one of the following modes below via UP/DOWN buttons and then press ENTER to confirm. OFF 1 2 ON 2 1 DIMMING CURVE SETTING: Select the Dimming Curve Setting by pressing MODE button until DIMMING CURVE is displayed and then press UP/DOWN buttons to select desired Dim Curve Standard (default), Stage, TV, Architectural, or Theatre.
w w w . e l a t i o n l i g h t i n g .