STREAMER Users Instructions Elation Professional R 4295 Charter Street Los Angeles CA. 90058 www.elationlighting.
Features We would first like to congratulate you on the purchase of this magic fibre lighting-STREAMER! Its main features include: -USITT DMX512(1990) multiplexed digital control, via 3 pin XLR connector. -Light plastic material case(IP:V0). -Slave, Auto and Audio function modes available. -9 built-in chasing patterns plus a sequence of 9 patterns(AUTO). -0~100(/0.1s) DMX fade time setup. -Stand by function allows you to kill overall output instantly.
General Information Every STREAMER has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your controller for any damage and be sure all equipment necessary to operate the unit has arrived intact. In case damage has been found or parts are missing, please contact us or your nearest dealer/distributor for further instructions.
Controls & Functions Front View Rear View 1 6 STAND BY SLAVE DMX AUDIO POWER IN: AC 90-264V~ 50/60Hz. AUTO 2 DMX OUT DMX IN PUSH 3 2 MODE MENU UP 8 DOWN 1 3 1 2 3 7 4 5 1. Digit Segment Display The 4-digit LED display shows the menu and operating functions which users can choose from. It also shows user desired levels including DMX address, pattern numbers and fade time. Segment Display Related Info.
Unpacking Notice Top covre(PVC) Unpack: Remove the base cover and take out the fiber tube from paper cylinder. F i x Sta n d Fi b r e t ub e Cyli n der TOP Pull Out Ba s e c o v e r (PVC) Installation Procedures Before installation, please make sure that KIT ASM-A has been hanged fully and safely. 1. The first Fibre Tube(A1) Installation(See figure-2) Step1 Firstly assemble A2(Plastic cover)and E(Aluminum sheet) together with one screw by the screwdriver.
Installation Procedures 2. The second Fibre Tube(A1) Installation(See figure-3) Step3 And repeat Step2 to install the second A1(Fibre tube) and fix them well. (Figure-3) 3. The third Fibre Tube(A1) Installation(See figure-4) Step4 In like matter, select any of the rest two Fibre Tube(A1) and place it on KIT ASM-A well, assemble Plastic cover(B2) and screw with two screws by the screwdriver, then fix them with C(Plastic tube). (Figure-4) 4.
Operation Guide Slave 0 RGH In this mode, users can have DMX address setting and DMX fade time , and daisy chain up to some units together to get a sync lighting show. ' 0 ; &RQW URO Channel 1 is the rotary speed for motor, channel 2 is the rotary direction for motor (0~127 is to rotate clockwise and 128-255 is anticlockwise movement), and Channel 3-6 is the color for the fibre lighting tube. Please follow the set-up specifications(RGB color and DMX value Table) that come with your DMX controller.
Operation Guide AUTO 0 RGH 1. Press the Mode button to access the AUTO mode, the AUTO indicator will be lit on the LED-display. And your unit patterns will run automatically. STAND BY SLAVE DMX AUDIO AUTO MODE 2. And use Up/Down button to select your desired chasing patterns within the range of 1-9 & AUTO. MENU UP DOWN STAND BY SLAVE DMX AUDIO AUTO MODE MENU UP DOWN AUDIO 0 RGH 1. Press the Mode button to access the AUDIO mode indicator will be lit on the LED-display.
Operation Guide RGB color and DMX value Table DMX (N) (Decimal) 0 1-2 3-33 34 35-65 66-69 70-100 101 102-132 133-136 137-167 168 169-199 200-206 207 208-210 211 212-215 216-218 219-222 223-225 226-228 229 230-232 233 234-236 237 238-240 241-244 245-247 248-251 252-254 255 Red (%) 0 100 100 100 100-(N-34)x3 0 0 0 0 0 (N-136)x3 100 100 100 100 100-(N-207)x12 50 50-(N-211)x6 50-(N-215)x6 (N-217)x6 38+(N-223)x6 50+(N-225)x12 100 100 100 100-(N-233)x12 50 50-(N-237)x6 25-(N-241)x6 (N-243)x6 25+(N-247)x6 50+(N-2
Operation Guide Using the Remote Control Properly When using your Remote Control(included), please ensure to operate it within the effective range of the infrared sensor, so that you may operate your STREAMER at any safe place. Overview POWER ON DMX STAND BY AUTO AUDIO FADETIME PATTERN STREAMER Remote Control POWER ON key: STAND BY key: DMX key: AUTO key: AUDIO key: FADETIME key: PATTERN key: To turn the power on. To allow you to kill overall output instantly. To access Slave Mode.
Technical Specifications Power Requirement...........................................................AC90~264V-50/60Hz LED-display Screen.........................................................4-digit segment display DMX In.............................................................................3-pin XLR male socket DMX Out.......................................................................3-pin XLR female socket Accessory....................................................................
24-004-1843 Rev1.1 Elation Professional R A Division of the American DJ Group of Companies 4295 Charter Street Los Angeles, CA 90058 USA Tel: 323-582-3322 Fax: 323-582-3311 Web: www.elationlighting.com E-mail: info@elationlighting.
