Water Filtration Vacuum Cleaner User Guide Model: EV-5199 220-240V 50HZ,1200W,1400W max.
IMPORTANT SAFEGUARDS 1. Safety Precautions During Use To ensure safe and correct use of your product, do not operate without first reading this operation manual thoroughly. To avoid shortening the life span or damaging your product, do not use the machine with parts or accessories not original. Use only original spare parts and accessories. Do not operate the machine with wet hands. Do not operate the machine in an excessively wet environment.
electrical shock. Always switch-off your machine and disconnect the AC plug from the mains outlet when the product is not in use. Do not use your machine if the AC cord or plug is damaged. Do not tamper with a damaged AC cord or plug. Return the product to the Service Centre for inspection. Do not use the product if the plug seems excessively loose. Features Water-based vacuum system plus HEPA filters system.
Part and Accessories Index Handle Flexible Hose Telescopic Tube Rewind Button Carrying Handle Switch Button Brush Big Wheel Handy Cyclonic Attatchment Crevice Nozzle Tank Cover Floater Sponge Filter Meshed Filter Cage Duster Brush Curved Tube Water Tank Water Brush 4
Preparation Before Use Caution Do not overfill the water container. Note the `Maximum Level` marking. Do not fill the water container with anything other than water. Always empty the dirty water, clean and store your machine correctly after each use. 1. Setting Up the Product Push the release button at both two sides and rotate the front cover upwards. (Fig.1) Remove the water container using the attached handle. (Fig.2) Remove the filter assembly from the water container.(Fig.3).
Connect the telescopic tube to the flexible hose 2. Power On Extract the AC power cord fully by holding the cord and pull it towards you. Do not pull the cord by holding the plug. as this will damage the cord. Connect the plug to a suitable mains power outlet with the correct voltage. (Fig.6) Caution: Before connect the plug to the power socket, unwind a sufficient length of cable. A yellow mark on the power cable shows the ideal cable length. Don’t expend the cable beyond the red mark.
Use of your product 1. Suction Power Selection Button There are four suction power setting, Low, Medium, High and Turbo. Use (+) or (-) button on the main body of the machine to select the desired setting. (Fig.8) The current suction power is indicated by the number of green indicator lights. For example, three green lights means the suction power is now in the 3rd high position. 2. Telescopic Tube The extention Telescopic Tube gives you added flexibility and control.
Caution: If you use your machine for liquid suction. Make sure you first reduce the amount of water in the tank by about half. It is also important not to allow the tank to become too full of vacuumed liquid. When you finish, empty the tank completely and vacuum up about one liter of clean water to rinse clean the inside of the Flexible Hose and the Telescopic Tube. Repeat if necessary.
1. General You may wipe the machine with a damp cloth. Synthetic detergent may be used on plastic and metal parts if necessary. Make sure you wipe the machine and its parts dry before storage. Do not use strong cleaning agents such as benzene or thinner to clean the machine. Always store your product and parts after they are completely dried. 2. Cleaning and Maintenance of the filter assembly.
HOW TO USE HANDY CYCLONE ATTACHMENT What it is: 1. 2. 3. 4. 5. An additional cyclonic dust collecting device for all vacuum cleaner. With detachable transparent dust tank, capacity 1 L. Easy to drop the dust. Easy to see the dust cleaned. A long deep dust tank enabling a better cyclonic swirl function. 6. Makes your vacuum cleaner with better cleaning efficiency. parts and Accessories Preparation before use : Assembly the cyclonic attachment: 1. 2.
Fig.01 How to use this attachment: 1.Connect the cyclonic attachment to the flexible hose handle and telescopic tube。Then can use it for cleaning job. (Fig.02,Fig03) Fig.02 Fig.03 2. If the diameter of the attachment is not fitting with the hose handle and/or the telescopic tube, Please use the additional connectors to connect with the attachment, then connecting with the handle and tube. (Fig.
3. Fig.04 After finishing the cleaning, You can take out the dust cup and drop the dust to dust bin. You can wash the dust cup with the water. (Fig.05, Fig06) Fig.05 Note: Fig.06 Pls don’t use this attachment to sucking water or liquid , if the vacuum cleaner is not a wet/dry vacuum.
Troubleshooting Do not disassemble or attempt to repair the machine yourself Conditions Possible Cause and Solution 1. The machine stops during operation and all four suction power indicator lights start blinking together. 2. The machine does not start If the sucked dust or water is too full, then the float switch will goes up to stop the suction. It is a safety device, not the machine is damaged. Pls empty the dust or water (or reduce the water down than the MAX line).