User's Manual

ENG man MITO-VETTA 915 00 Radio Remote Control System MITO-VETTA-915
- Page 10 -
3. PROGRAMMABLE FUNCTIONS
3.1 ACCESS TO PROGRAMMING MODE
Outlined below are certain programmable functions that can be set by the user ONLY in certain versions. Only the
frequency range programming is always available.
WARNING!
Be careful when programming functions other than the original ones in customised radio remote controls or units that are
already installed on a machine, as the new functions might lead to abnormal operation of the machine. We advise against
programming or making programming tests on radio remote controls that are already installed on a machine.
CHANGE
FREQUENCY
GROUP
(submenu1)
T4 and/or T9
and/or T10 and/or T11
FROM MAIN MENU
ACTIVATE T2
SUBMENU ACCESSED.
HERE YOU CAN SET A FREQUENCY GROUP
AS SPECIFIED BELOW.
IF NO SELECTION IS MADE WITHIN 10 SECONDS,
SYSTEM RETURNS TO MAIN MENU.
GROUP 1
869.7125 MHz
869.8125 MHz
869.9375 MHz
FROM SUB-MENU1
ACTIVATE T4 e T10
IN SEQUENCE
SET FREQUENCY RANGE:
869.7125 - 869.8125 - 869.9375 MHz.
AUTOMATIC RETURN TO MAIN MENU; WAIT
10 SECONDS AND SYSTEM EXITS MAIN MENU.
GROUP 2
869.7625 MHz
869.8625 MHz
869.9875 MHz
FROM SUBMENU1
ACTIVATE T4 e T11
IN SEQUENCE
SET FREQUENCY RANGE:
869.7625 - 869.8625 - 869.9875 MHz.
AUTOMATIC RETURN TO MAIN MENU; WAIT
10 SECONDS AND SYSTEM EXITS MAIN MENU.
GROUP 3
(default)
869.7375 MHz
869.8375 MHz
869.9625 MHz
FROM SUBMENU1
ACTIVATE T9 e T11
IN SEQUENCE
SET FREQUENCY RANGE:
869.7375 - 869.8375 - 869.9625 MHz.
AUTOMATIC RETURN TO MAIN MENU; WAIT
10 SECONDS AND SYSTEM EXITS MAIN MENU.
T2
T4 T10
T4 T11
T9 T11
(depending on group)
CHANNELS
TO BE USED
WHAT TO DO
CHECK LIGHT
BLINKS 3 TIMES
AT 1Hz
BLINKS
2 QUICK BLINKS
WITHIN 1 SEC.
BLINKS 3 TIMES
AT 1Hz
BLINKS 3 TIMES
AT 1Hz
AUTOMATIC
INCREMENT
OF
FREQUENCY
GROUP
(1,2...)
FROM SUBMENU1
ACTIVATE T1
(STOP BUTTON)
SET NEXT FREQUENCY GROUP.
TRANSMITTING UNIT SWITCH OFF.
BLINKS AT 1Hz AND
THEN SWITCH OFF
T1
3.2 FREQUENCY RANGE PROGRAMMING
ACCESS TO
PROGRAMMING MODE
(main menu)
CHANNELS
TO BE USED
WHAT TO DO
CHECK LIGHT
WITH AT OFF,
ACTIVATE T12
AND THEN T11
WITHIN 1SEC
ACCESS TO MAIN MENU CONFIRMED,
CHECK LIGHT ON STEADY. TX SENDS NO COMMANDS.
DEPENDING ON RADIO REMOTE CONTROL
CONFIGURATION, IT IS POSSIBLE TO ACCESS
TO 4 DIFFERENT PROGRAMMING SUBMENUS:
WITH T12 AND T11
ACTIVE, 1Hz BLINKING
FOR 5 secs THEN
STEADY ON
- FREQUENCY RANGE (always available)
- AUTO-SHUTDOWN TIME
- PIN CODE
- CHANNEL LATCHING
NOTE:
system exits main menu and transmitter (AT) shuts down after 10sec
of inactivity.
T11 T12
IF NO SELECTION IS MADE WITHIN 10 SECONDS,
SYSTEM RETURNS TO MAIN MENU.
STOP
ON / OFF
CHECK
CHARGE
TA02
T9
T4
T10
T3
T7
T5
T11
T2
T12
T8
T1
LAYOUT COMMAND