GSM ALARM SYSTEM ELDES EPIR
User Manual v.1.2 Safety instructions Please read and follow these safety guidelines in order to maintain safety of operators and people around: • • • • • • Alarm system ELDES EPIR (later referenced as system or detector) has radio transceiver operating in GSM850, GSM900, GSM1800 and GSM1900 bands. Don’t use the system where it can be interfere with other devices and cause any potential danger. Don’t use the system with medical devices. Don’t use the system in hazardous environment.
EN The device is powered by a backup battery. The device is switched off by unplugging external electrical power supply and disconnecting battery connector which is accessed by opening device frame cover. Fuse F1 type - C1S 2.5A. Blown fuse cannot be replaced by the user and the replacement fuses have to be exactly the same as indicated by the manufacturer. If you use I security class computer for setting the parameters it must be connected to earth.
Limited Liability The buyer must agree that the system will reduce the risk of fire, theft, burglary or other dangers but does not guarantee against such events. “ELDES UAB” will not take any responsibility regarding personal or property or revenue loss while using the system. “ELDES UAB” liability according to local laws does not exceed value of the purchased system. “ELDES UAB” is not affiliated with any of the cellular providers therefore is not responsible for the quality of cellular service.
EN CONTENT 1. General Information 1.1 1.2 1.3 1.4 1.5 Functionality................................................................................................................................................. 24 Operation description............................................................................................................................... 24. Technical specifications ................................................................................................................
1. General Information 1.1 Functionality ELDES EPIR – microcontroller based security system for houses, cottages, country homes, garages and other buildings. The system can be used in following applications: • Property security • Mains 230V power status with SMS message • Remote listening of what is happening in the secured property with built in microphone Also capable of informing user about mains 230V power status over cellular GSM network. 1.
EN 1.3 Technical Specifications Electrical and mechanical specifications Supply Voltage 11-15V Back-up Battery voltage, capacity 8.
1.5 System installation The system should be installed indoors. Choose location where unauthorized entry is most likely. To avoid fault alarms, avoid installing in following locations: • locating lens towards direct sunshine, e.g. facing windows • near devices with high temperature fluctuations, e.g.
EN 1. Fix the holder to the wall 2. Insert SIM card with PIN code disabled 3. Plug power supply connector 4. Place ELDES EPIR into the holder 5. Plug power supply into mains socket 6. The system starts in 1-2 minutes. When LED is off, move your hand in front of ELDES EPIR lense and watch the system detecting motion and turning on LED for few seconds. If LED indicator is blinking fast (few times a second), could be that SIM card in not inserted properly or PIN code has not been disabled.
2. System pre-operation and essential control commands VERY IMPORTANT!!! Underscore symbol ‘_’ in this manual is used to represent space. When writing SMS messages, every underscore symbol should be replaced by single space symbol. XXXX – means password. Don’t leave any space at the beginning and the end of the message. To set ELDES EPIR system parameters easier and quicker you can use the computer, USB cable and configuration program ELDES EPIR ConfigTool. You can read more in chapter 4.2. 2.
EN Central number can be entered by sending SMS message: XXXX_SMS_+37011111111 XXXX – is a password. Default password is four zeros: 0000. SMS central number is provided by cellular network provider. Example: 0000_SMS_+37069899992 Message should be sent to the number of SIM card which is placed into the system. If all went correct, the system will send a message: SMS central number has been successfully changed to +37011111111 2.
2.3.1 Saving or Changing numbers Send SMS message with text to ELDES EPIR: XXXX_NR1:37011111111_NR2:37011111111_NR3:37011111111_ NR4:37011111111_NR5:37011111111 Ones should be replaced with user numbers. Numbers don’t have to be entered all or in sequential order right away. E.g.
EN 2.4 Date and time settings It is important to set correct date and time, so that the system can send reports at specified times. Date and time can be set by sending following format SMS message: XXXX_MMMM.mn.dd_hh:mi Where MMMM – means year, mn – month, dd – day, hh – hour, mi – minutes 0001 2009.01. 01 14:15 E.g. 0000_2009.01.01_14:15 USER MANUAL V.1.
3. Additional system capabilities 3.1 Renaming security zones Manufacturer initially set following zone names: Z1- Motion. User is free to change any of these names keeping in mind that names cannot be same or match system commands. Zone names can be changed with following SMS message: 0000_Z1:NewZoneName 0001 Z1: passage Zone names can have up to 14 characters. 3.2 System and Zone status To find out current zone names, settings and status, send SMS message XXXX_STATUS The system will reply, e.g.
EN 3.4 Info on status SMS Security system EPIR can be inquired at any time about its status, signal strength, zone status. At the same time system can be tested. If SMS response message is received, means system is functioning properly. This is also useful for users with prepaid SIM cards. It can be checked whether SIM card has enough remaining balance for sending SMS. Send SMS message: XXXX_INFO 0001 INFO The response SMS message will be received, e.g. 2008.08.
3.5 Blocking unknown incoming numbers By default ELDES EPIR can be controlled from any of the pre-programmed numbers NR1 .. NR5. But user can access the system and control parameters from any number as long as password is know. To enable this feature, send SMS message: XXXX_STR:ON 0001 STR: ON To disable this feature, send SMS message: XXXX_STR:OFF 3.6 External power supply control The system ELDES EPIR will report every time mains 230V power supply fails or recovers.
EN 3.8 SMS message delivery to multiple users Upon activated alarm, SMS messages are repeatedly sent until first successful delivery to one of the users. System starts with NR1, and if delivery fails, follows with NR2, etc. It is also possible that SMS message will be sent to all recorded users. To enable this function, send SMS message: XXXX_SMSALL:ON To disable this function, send SMS message: XXXX_SMSALL:OFF 3.
3.11. Using Wireless Devices in EPIR868 System ATTENTION: binding of wireless devices is supported only by ELDES EPIR868. Security system ELDES EPIR868 can be expanded by connecting additional wireless ELDES devices: • PIR sensors EWP1 (motion detectors). It allows to expand secured territory up to 16 additional security zones; • expansion modules EW1 with 2 inputs and 2 programmable outputs. It is used for attaching more devices (various detectors, sirens) to the security system.
EN USER MANUAL V.1.
4. Appendix 4.1 Restoring default parameters To restore system default parameters, remove upper half of device (with detector lense) and connect power supply. Then press and hold on the button to restore default parameters (see chapter 1.4) until LED indicator will blink 5 times. Disconnect power supply. 4.2 ELDES ConfigTool configuration software Configuration program works only with ELDES EPIR devices starting with v2 version.
EN 4.4 Technical support Indication Possible reason Lense indicator OFF · No mains 230V power · Power supply connector unplugged · out of coverage or to weak signal.
