TADAO® EDITION USER MANUAL English
English TADAO® EDITION .
English IMPORTANT SAFETY GUIDELINES WARNING • • • • • • • • • • • • • • • • • • • • • • • • 1 This paintball marker is NOT a toy. Misuse can cause serious injury or death. Kingman recommends that the customer be at least 18 years of age to purchase this product. Person under 18 years of age must have adult supervision when using this product. Read this User manual before using this product.
English 8 STEPS TO START AND PLAY IMPORTANT: Please read the Safety and Operation Guidelines before you start the 8 quick steps to Start and Play. 1. Insert the barrel blocking device 3. Install a CO2/Compressed air tank 2. Install a battery in the grip panel 4. Install a paintball loader and add paintballs in the loader 5. Put on your paintball goggles and cock back the marker 7. Power on the circuit board and remove the safe mode 6. Remove the barrel blocking device 8.
RECOMMENDED PAINTBALL SAFETY GEAR Cap or Hood NEVER look down the barrel with or without your paintball goggles ON. Paintball Goggles NEVER look down the barrel of a loaded or unloaded marker. Neck Protector Paintball Jersey w/ Body Armor under WARNING: UNSAFE NEVER shoot or point your marker at a person that is not in a designated paintball facility and without proper EYES/FACE/ EARS protection designed specifically for the sport of paintball.
English INSTALLING A CO2 / COMPRESSED AIR TANK CO2 / COMPRESSED AIR TANK WARNINGS Firmly hand tighten the CO2 / Compressed Air Tank clockwise into the markers C/A On/Off adapter. HELPFUL TIP: Before installing a CO2 / Compressed Air Tank, make sure that the tank is full and that it has a urethane bottle o-ring on the top of the valve to prevent air leaks. IMPORTANT: You should never need to use any hand tool to attach a CO2 / Compressed Air Tank to the C/A On/Off adapter.
English BATTERY INSTALLATION CHARGING INSTRUCTIONS Spyder 9.6volt Battery (US LED) optional accessory To charge a Spyder 9.6 NiMH battery, the circuit board must be in the OFF position. Spyder batteries (JE1015) are not fully charged when purchased. Using the supplied Spyder LED A/C Charger (JE1029), plug the charger into the charger port located at the rear of the trigger frame. For a complete charge, Kingman recommends a charging time of 6-8 hours.
English TADAO® CIRCUIT BOARD SETTINGS POWER AND EYE OPERATION Press the Power Button to turn marker on. It will boot instantly, showing a Solid Red LED in the grip frame. The marker will be in “Safe Mode” when the marker is first turned on.
English To INCREASE your velocity fps using the Allen wrench, turn the Velocity Adjuster / Spring Guide clockwise. To DECREASE your velocity fps using the Allen wrench, turn the Velocity Adjuster / Spring Guide counterclockwise. NOTE: Allen wrench provided in the spare parts kit. NOTE: Velocity Adjuster / Spring Guide doesn’t remove from the rear of the Sticker Plug. NOTE: The velocity of this paintball marker ranges from approximately 240 – 300 feet per second (fps).
English DISASSEMBLE / REASSEMBLE AND CLEANING OF REAR INTERNALS REASSEMBLY REAR INTERNALS CONNECTED VBT014 DISCONNECTED STK008 STF001 REC045 STP028 SPR014 STB002 Part Names and Numbers described in this section: Top Cocking Knob (#STK008) Delrin Bolt w/ Locking Knob & O-Ring (#VBT014) Striker Bolt (#STB002) Striker Plug (#STP028) Striker Spring (#SPR014) Striker Buffer (#STF001) Receiver (#REC045) QUICK CLEAN DISASSEMBLY Lift upward on the Top Cocking Knob to disconnect the Delrin Bolt from the Str
English ANTI CHOP EYES CUP SEAL REMOVAL BLS003 ITP012 BLS 011 BLS012 LPC028 SPR013 ITP011 ITP017 ORG023 VRT028 WRH008 ITP019 SCR027 SCR035 Part Names and Numbers described in this section: Eye Panel (#BLS011/BLS012) Ball Stopper (#BLS003) Eye Panel Screw (#SCR035) Eye Wire Harness (#WRH008) ANTI CHOP EYES The Anti Chop Eyes help prevent the chopping of paint by not allowing the marker to fire until a paintball is properly chambered in the breach.
English TROUBLESHOOTING REGULATOR SCHEMATIC ONE OR MORE OF THE FOLLOWING MAY CAUSE RECOCKING RELATED ISSUES: • Need lubrication on the following O-ring (#ORG001) (see Disassemble / Reassemble). • The pressure in the tank is too low and possibly needs to be refilled. • Striker O-ring (#ORG001) is damaged or missing. Replace with a new Kingman approved Striker O-ring. NOTE: The Striker O-ring can not be substituted with a black or urethane bottle o-ring.
English ELECTRA w/Eye TADAO® EDITION PARTS LIST ASA023 ASA021 ASA018 ASA030 * BAR001 BAR028 BLS003 BLS009 BLS010 BLS011 BLS012 31223 ELM001 ELM002 ELM004 ELM008 FND010 FND030 GRP005 HSE010 HSF004 HSF009 C/A On/Off Adapter Knob (polished black) C/A On/Off Retaining Screw C/A On/Off 1/8 Hose Plug C/A On/Off Adapter (polished black) Spyder Barrel Plug/BBD 12” 2PCS Barrel (polished black) Ball Stopper Ball Stopper / Eye Wire Insert - right Ball Stopper / Eye Wire Insert - left Aluminum Eye Panel - right (polis
WARRANTY STATEMENT Kingman warrants the original retail purchaser that this product is free from defects in material and workmanship under normal use and service for a period of (1) year from the original date of purchase. Any Electronic Components in an Electronic Spyder marker are warranted for (6) months and the Tadao® Circuit Board for (3) months from the original date of purchase. Kingman agrees to repair or replace (at its discretion) any product within (a reasonable period of time).
XL
