USER MANUAL 43.8 INCH LED MONITOR eiQ-43SUWD120FSHDR600 Thank you for choosing electriQ Please read the user manual before using this monitor and keep it safe for future reference Visit www.electriQ.co.
CONTENTS SAFETY 3 PARTS LIST 5 STAND INSTALLATION 6 WALL MOUNT INSTALLATION 7 CONNECTIONS AVAILABLE 8 GETTING STARTED 8 MONITOR CONTROLS 8 INITIAL SET UP 9 SHORTCUT BUTTONS 9 MENU OPTIONS 9 INPUT SOURCE 10 BRIGHTNESS / CONTRAST 10 COLOUR SETTINGS 11 PICTURE QUALITY SETTINGS 12 DISPLAY 13 AUDIO 13 MULTI WINDOW 14 OSD 15 OTHER 16 TECHNICAL SPECIFICATION 17 TROUBLESHOOTING 18 SUPPORT 18 2
SAFETY INFORMATION • • • • • • • • • • • • • • • • • • • • Read these instructions - All the safety and operating instructions should be read before this product is operated. Keep these instructions - The safety and operating instructions should be retained for future reference. Heed all warnings - All warnings on the appliance and in the operating instructions should be adhered to. Follow all instructions - All operating and usage instructions should be followed.
• • • • • • • • • Disconnect the power immediately and seek professional help if the plug or cable is damaged, liquid has spilt onto the unit, if accidentally exposed to water or moisture, if anything accidentally penetrates the ventilation slots or if the unit does not work normally. Do not remove the safety covers. There are no user serviceable parts inside. Trying to service the unit yourself is dangerous and may invalidate the product's warranty.
PARTS LIST Monitor Bolts (B) x 4 (For Attaching Stand) Power Cable (AC 100-240V, 50/60Hz) Bolts (A) x 3 (For Stand Assembly) Extension Bolts x 4 (For Wall Mount Installation) DP Cable USB Cable User Manual Remote Control Stand – Upright Section Stand - Base 5
STAND INSTALLATION 1. Open the packing box, take out the bracket and the base, and use three bolts (A) to attach the base of the stand to the upright section, as shown below: Bolts x 3 Mounting Plate 2. Attach the stand onto the rear of the monitor by locating the top of the upright section into position on the rear of the monitor before clipping in the bottom of the mounting plate. Ensure the mounting plate is fully located. 3. Use 4 x Bolts (B) to secure the mounting plate to the rear of the monitor.
WALL MOUNT INSTALLATION • The monitor is provided with mounting holes for a VESA approved wall mounting bracket (not supplied). • M4 x12 bolts (not supplied) should be used to attach the bracket to the extension bolts. • Do not use screws longer than specified or damage will occur to the internal components. Mounting Nuts Extension Bolts x 4 1. When wall mounting the 4 x Extension bolts should be fitted into the mounting holes on the rear of the monitor, ensuring that they are suitably tightened.
CONNECTIONS AVAILABLE ON THE MONITOR 1. Type-C 2. HDMI 2 (HDMI 1.4, 75Hz, Free Sync) 3. HDMI 1 (HDMI 2.0, 120Hz, Free Sync) 4. DP (Display Port 1, 120Hz, Free Sync) 5.
INITIAL SETUP CONNECT THE MONITOR TO A POWER OUTLET 1. Press the POWER button on the monitor or to turn it on (The indicator will be blue) 2. Connect the relevant cable to the corresponding input on the monitor. The source will be automatically detected. SHORTCUT BUTTONS The monitor includes one touch options to access common settings. MENU OPTIONS The menu for the monitor can be accessed by pressing the menu button on the control panel.
OSD MENU INPUT SOURCE Signal Switch the signal input or select the source. DP, HDMI1, HDMI2, Type-C BRIGHTNESS/CONTRAST Brightness Adjust the brightness of the display between 0 and 100. Contrast Adjust the contrast of the display between 0 and 100. DCR Turn the Dynamic Contrast Ratio Feature On or Off. Black level Adjust the black level of the display between 0 and 100.
COLOUR SETTINGS Gamma Change the Gamma value for the display between 2.0, 2.2 and 2.4. Picture Mode Change the picture mode between Standard, Photo, Movie, Game, FPS and RTS. Change the Colour Temperature of the display to Normal, Warm, Colour Cool or User. When the User Mode is selected, the Red, Green, and Temperature Blue values can be adjusted independently between 0 and 100. Low Blue Light Change the blue light emitted by the display between0 and 100. Hue Change the Hue value between 0 and 100.
PICTURE QUALITY SETTINGS Sharpness Change the display Sharpness between 0 and 100. Response Time Turn the Response Over Drive feature between Off, High, Middle of low Noise Reduction Adjust the level of Noise Reduction between Low, Medium, High, or Off. Super Resolution Change the Super Resolution value from 0 to 5. Dynamic Luminance Control Turn the Dynamic Luminance Control feature On or Off. MPRT Turn the motion blur on or off.
DISPLAY Aspect Ratio Change the image aspect ratio to Wide Screen AUDIO Mute Turn On and off to mute and unmute the audio output. Volume Adjust the output volume between 0 and 100. Audio Source Chose which source the audio is output from.
MULTI-WINDOW Multi-Window Choose the different formats of multi window display between Off, Picture in Picture (PIP) and Picture By Picture (PBP 2Win) Sub Win2 Input Choose the source of the second window between HDMI 1 and HDMI 2. PIP Size Adjust the size of the secondary source in PIP and PBP modes between Small, Medium and Large PIP Position Set the position of the secondary source in PIP and PBP modes between Top Right, Top Left, Bottom Right and Bottom Left.
OSD Language Change the OSD Menu display language between English, Chinese, Korean, Russian, Spanish, Japanese and French. OSD H Position Change the horizontal position of the OSD Menu. OSD V Position Change the vertical position of the OSD Menu. OSD Transparency Change the transparency value of the OSD Menu between 0 and 100. OSD Time Out Change how long the OSD Menu is on before it automatically exits.
OTHER Free Sync Mode Turn Free Sync On or Off. HDR: Turn HDR On (requires HDMI 2.0 input). DP Version Change the DP version Reset Restore factory default setting. HDR Turn the HDR on or off.
TECHNICAL SPECIFICATION eiQ-43SUWD120FSHDR600 Screen Size 43.8” Diagonal Panel Type VA Panel Aspect Ratio 32:9 Power Supply AC 100-240V ~ 50/60Hz, 2.2A Power Consumption 60W Typ, 190W Max Dimensions 1089 * 547 * 287 mm Net / Gross Weight 11.5 kg / 14.4 kg Terminals Picture Product Model Maximum Resolution 3840 * 1080 Brightness 600 cd/m2 (HDR) / 400 cd/m2 Static Contrast 1000:1 Response Time 6ms Viewing Angle (H/V) 178° / 178° USB Input USB-B x 1, USB-A x 3 USB 3.
TROUBLESHOOTING PROBLEM No power SOLUTION Insert the plug securely into the power outlet. Ensure that the equipment is connected properly. No picture Ensure the correct input is selected. Buttons on the monitor don’t do anything Disconnect the power plug and then reconnect it. (The unit may not be operating properly due to lightning, static, or other factors.) Noise or other interference Electronic equipment near the unit may be causing interference. Relocate the unit or move the equipment.
