USER MANUAL BLADELESS HEATER WITH AMBIENT LIGHT AND SMART APP CONTROL eiQ-AM09W Thank you for choosing electriQ Please read this user manual before using this heater and keep it safe for future reference. Visit our page www.electriQ.co.
CONTENTS SAFETY INSTRUCTIONS 3 FEATURES 5 DIAGRAM 5 OPERATION 6 CONTROL PANEL AND SETTINGS 6 REMOTE CONTROL 7 CONNECTING THE APPLIANCE TO WIFI 8 CONTROLLING YOUR APPLIANCE THROUGH THE APP 14 MAINTENANCE 19 TROUBLESHOOTING 19 TECHNICAL DATA 20 SUPPORT 20 PRODUCT FICHE 21 Page 2 of 21
SAFETY INSTRUCTIONS Important! • Carefully read the instructions before operating the unit • This appliance is for indoor use only. • Rating: This unit must be only connected to a 220-240 V / 50 Hz earthed outlet. • Installation must be in accordance with regulations of the country where the unit is used. • If you are in any doubt about the suitability of your electrical supply have it checked and, if necessary, modified by a qualified electrician. • This heater has been tested and is safe to use.
• The heater is designed to be used at temperatures above -20°C. If it is exposed to temperatures below this, it must be allowed to warm above this level before operation. Do not attempt to repair, disassemble or modify the appliance. This unit contains no user-serviceable parts. Always unplug or disconnect the appliance from the mains power supply when not in use, or when moving or cleaning it. Do not pull the cord to unplug the heater. Keep the heater clean.
eiQ-AM09W BLADELESS HEATER FEATURES ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ ⚫ Slim design takes minimal space High Speed Motor with Fan mode and 2 Heat settings Swing Function 7.5 hour standby timer. Remote Control. Built in ambient light.
OPERATION Your heater may be operated by using the manual controls located on the control panel, by your remote control, or by the smart app. POWER SWITCH ON THE BACK OF THE UNIT Used to turn the bladeless heater ON and OFF. This should be used to turn off the appliance before leaving unattended. CONTROL PANEL AND SETTINGS ON/OFF BUTTON Used to turn the bladeless heater ON and OFF.
REMOTE CONTROL Your bladeless heater is supplied with a remote, which allows control of the main features of the appliance. ON/OFF: Turns the heater On and Off MODE: Cycles between Cooling Fan, Low heating and High Heating. TIMER: Press repeatedly to set the On timer in 30 minute intervals. The time set will be displayed on the unit. SWING: Press to turn the Swing Function On and Off.
CONNECTING THE APPLIANCE TO WIFI DOWNLOAD THE APP TO YOUR PHONE Download the ”TUYA SMART” app, from your chosen app store, using the QR codes below, or by searching for the app in your chosen store.
MODES AVAILABLE FOR SETUP The heater has two different setup modes, Quick Connection and AP (Access Point). The quick connection is a quick and simple way to set the unit up. The AP connection uses a direct local wifi connection between your phone and the heater to upload the network details. When first turned on using the switch on the rear of the unit, the Ambient Light indicator will flash rapidly, showing that the unit is in Quick connection mode, and ready to set up.
REGISTER THE APP 1. Press on the register button at the bottom of the screen. 4. A verification code will be sent by the method selected in step 3. Enter the code into the app. 2. Read the Privacy policy and press the Agree Button. 5. Type in the password you would like to create. This needs to be 6-20 characters, with letters and numbers. Page 10 of 21 3. Enter your email address or phone number and press continue to register. 2. The app is now registered.
SETTING UP YOUR HOME WITHIN THE APP TUYA is designed so it can work with a large number of compatible smart devices within your home. It can also be set up to work with multiple devices within different houses As such during the setup process, the app requires that different areas are created and named to allow easy management of all your devices. When new devices are added, they are assigned to one of the rooms you have created. CREATING ROOMS 1. Press on the ADD HOME button. 3.
CONNECTING USING THE QUICK CONNECTION METHOD Before initiating the connection, make sure the unit is in standby mode (Power switch ON, but unit turned off), with the Ambient Light indicator flashing twice per second. If not follow the instructions for changing the connection mode. Also ensure your phone is connected to the wifi network. (We advise turning mobile data off during setup) 1. Open app and press “+” to add device, or use the add device button 2. Select the type of device 3.
CONNECTING USING AP MODE (ALTERNATIVE METHOD) Before initiating the connection, make sure the unit is in standby mode, with the Ambient Light Indicator flashing once per second. If not follow the instructions for changing the wifi connection mode. Also ensure your phone is connected to the wifi network. (We advise turning mobile data off during setup) 1. Open app and press “+” to add device, or use the add device button 4.
CONTROLLING YOUR APPLIANCE THROUGH THE APP THE HOME SCREEN Each device has its own entry on the home screen to allow the user to either quickly turn the unit on or off, or to enter the device screen to make other changes. Voice Control: Press to give verbal instructions for operation. Add Device: Add a device to the app, and go through the setup process.
DEVICE SCREEN The device screen is the main control screen for the heater, providing access to the controls to amend the functions and settings. Device Name Back: Returns to the Home Screen Edit Name: Use to change the name of the heater Current Mode: Shows the mode the heater is currently working in. Desired Temperature: Displays what has been set as the target room temperature.
SMART SCENES Smart Scenes is a powerful tool providing the option to customise the operation of the air heater based both on conditions within the room and outside influences. This gives the user the option of specifying much more intelligent actions. These are split into two categories Scene and Automation. SCENE Scene allows for a one touch button to be added to the Home Screen. The button can be used to change a number of settings in one go, and can change all the settings within the unit.
AUTOMATION Automation allows an automatic action to be set up for the device. This can be triggered by the Time, and a range of other influences, depending what other TUYA enabled devices you have on the network. 1. Press on the Scene tab at the bottom of the Home screen 2. Press on the Automation tab at the top of the screen. 4. Setup is very similar to the scene setup on the previous page, and includes an extra section for specifying a trigger for the scene to start.
PROFILE TAB The profile tab gives you the option to edit both your detail, and use the added features of the unit. HOME MANAGEMENT Home Management proves options for managing your TUYA account, giving options such as adding a home, adding and removing rooms, and sharing devices with family.
MAINTENANCE CLEANING AND STORAGE ATTENTION: Please shut off the unit and unplug from the mains before cleaning or performing any maintenance. Cleaning the surface Clean the heater with a duster or a soft wet cloth. Do not use chemical solvents (such as benzene, alcohol or gasoline) as they may cause irreversible damage. Make sure no water enters the control panel or gaps in the casing. Do not run the unit until completely dry.
TECHNICAL DATA Model Cable length Rated Input Power Supply Net Weight Dimensions eiQ-AM09W 1.5 meters 2 KW 220-240V/50Hz 3.3Kg 300mm x 185mm x 580mm electriQ UK SUPPORT www.electriQ.co.uk/support Please, for your own convenience, make these simple checks before calling the service line. If the unit still fails to operate call: 0871 620 1057 or complete the online form 1. Is the unit plugged into the mains? 2. Is the fuse OK? 3. Switch the unit off and wait three minutes to see if the issue is resolved.
PRODUCT FICHE Model Identifier: eiQ-AM09W Item Symbol Value Unit Heat Output Item Unit Type of heat input, for electric storage local space heaters only (select one) Nominal heat output Pnom 2.0 kW manual heat charge control, with integrated thermostat No Minimal heat output Pmin 1.0 kW manual heat charge control with room and/or outdoor temperature feedback No Maximum continuous heat output Pmax 2.
