USER MANUAL CANOPY COOKER HOOD eiQ52GCANOPY Thank you for choosing your electriQ cooker hood. This instruction manual is designed to provide you with all required instructions related to the installation, use and maintenance of the appliance. In order to operate the unit correctly and safely, please read this instruction manual carefully before installation and usage.
CONTENTS SAFETY 3 INSTALLATION 8 OPERATION 10 CLEANING AND MAINTENANCE 11 FILTER INFORMATION 12 LIGHT INFORMATION 13 TROUBSLEHSOOTING 14 SUPPORT 14 PRODUCT FICHE 15 3
SAFETY PRECAUTIONS Whilst this product is compliant with all safety requirements, incorrect or inappropriate use can lead to both personal injury and potential damage to property. Please read the contents of this instruction booklet thoroughly before fitting or using this appliance. • The cooker hood must be installed in accordance with the installation instructions and all measurements followed. • All installation work must be carried out by a competent person or qualified electrician.
• The plug must be accessible after installation for isolation in case of an emergency – or an appropriate fused switch if the unit is hard-wired to the mains via a spur. • The minimum distance between the surface of the hob and the lowest part of the hood should be at least 65cm. A distance of between 65cm and 75cm gives peak efficiency. • The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels.
V-FLAP INSTALLATION DIMENSIONS 6
OPTIONS FOR VENTING EXTERNAL VENTING If you have an outlet leading outside, your cooker hood can be connected as shown in the diagram using a flexible exhaust hose (not supplied). Any suitable extraction duct (enamel, aluminium, flexible pipe or other inflammable material with an interior diameter of 150mm) can be used. An adaptor is also supplied to enable you to connect your hood to pre-existing 120mm diameter ducting. Consideration of the route of the vent pipe should be made prior to installation.
INSTALLATION Before installation, ensure power is not connected. 1. Open the catch of metal filter door, remove the filter. 2. Remove the stainless-steel frame by removing the 4 x 4x10mm screws. 3. Remove the lid of the terminal box and unplug the wires to the hood controls. Then unplug the wires to the lights. 4. Fasten the Hood into the cabinet using the 12 x 4x18mm screws.
5. Screw the stainless-steel frame back into place using the 4 screws removed as described in step 2 above 6. Reconnect the wires to the controls and lights. 7. Replace the metal filter, pressing in until it clicks into place. 8. Install the air outlet pipe (optional).
OPERATION Button Function Remarks Turns the lights on or off Decreases the motor speed Displays fan speed (1, 2 or 3) Displays “0” Increases motor speed Turns motor on Automatic shutdown after 3 minutes Turns motor off Turns the motor and lights on Cycles motor speed (1, 2, 3, 1, 2, 3) Enters delayed shutdown mode (automatic shutdown after 3 minutes) Turns the motor and lights off 10 When and are on When fan is running Delayed shutdown mode or standby mode When on and are When is off When is on
CLEANING AND MAINTENANCE Before cleaning, switch the unit off and disconnect the power. Use a soft cloth moistened with mild soapy water or household cleaning detergent. Never use metal pads, chemicals, abrasive material or stiff brushes to clean the unit. NOTE: Do not use a steam cleaner to clean the hood as electrical components could be damaged or short-circuit as a result.
GREASE MESH FILTERS The mesh filters can be cleaned by hand. Soak them for about 3 minutes in water with a mild detergent then brush it gently with a soft brush. Do not apply too much pressure, or this may damage them. Leave to dry naturally out of direct sun light. Filters should be washed separately to crockery and kitchen utensils. It is advisable not to use rinse aid. INSTALLING GREASE MESH FILTERS To install filters: 1. Angle the filter into the slots at the back of the hood. 2.
BULB REPLACEMENT The bulb must be replaced by the manufacturer, its service agent or similarly qualified persons. Always switch off the electricity supply before carrying out any operations on the appliance. When handling the bulb, make sure it has completely cooled down before making contact with the hands. When handling bulbs hold with a cloth or gloves to ensure perspiration does not come in contact with the bulb as this can reduce the life of the bulb. 1. Remove the grease filter. 2.
TROUBLESHOOTING FAULT Light on, but fan does not work CAUSE The fan blade is jammed. The motor is damaged. Both light and fan do not work Light bulb blown Power cord loose Replace the bulb with correct rating. Plug in to the power supply again. Excessive Vibration The fan blade is damaged. The fan motor is not fixed tightly. Grease filters clogged Switch off the unit. Repair to be carried out by qualified service personnel only. Switch off the unit.
PRODUCT FICHE Symbol Model identification Annual Energy Consumption Time increase factor Fluid Dynamic Efficiency AEChood 56.0 f 1.7 FDEhood 9.
