USER MANUAL CANOPY COOKER HOOD eiQ80CURVSCTM eiQ80CURVBLTM Thank you for choosing your electriQ cooker hood. This instruction manual is designed to provide you with all required instructions related to the installation, use and maintenance of the appliance. In order to operate the unit correctly and safely, please read this instruction manual carefully before installation and usage.
CONTENTS SAFETY 3 INSTALLATION 7 OPERATION 9 CLEANING AND MAINTENANCE 9 FILTER INFORMATION 11 BULB REPLACEMENT 12 TROUBSLEHSOOTING 13 SUPPORT 13 PRODUCT FICHE 14 3
SAFETY PRECAUTIONS Whilst this product is compliant with all safety requirements, incorrect or inappropriate use can lead to both personal injury and potential damage to property. Please read the contents of this instruction booklet thoroughly before fitting or using this appliance. • The cooker hood must be installed in accordance with the installation instructions and all measurements followed. • All installation work must be carried out by a competent person or qualified electrician.
• The plug must be accessible after installation for isolation in case of an emergency – or an appropriate fused switch if the unit is hard-wired to the mains via a spur. • The minimum distance between the surface of the hob and the lowest part of the hood should be at least 65cm. A distance of between 65cm and 75cm gives peak efficiency. • The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels.
V-FLAP INSTALLATION DIMENSIONS 6
INSTALLATION Before installation, measure and confirm where you will be placing your cooker hood. See below for recommended installation height. Recommended installation height:700mm Required minimum installation height: 650mm Drill 3 x 8mm holes to accommodate the bracket. Screw and tighten the bracket onto the wall with the 3 screws and 3 wall plugs provided. Lift the cooker hood and hang onto the wall hook. Ensure everything is secure before commencing.
Drill 2x8mm holes & insert screws & wall plugs to further secure the hood. Measure where the hood chimney will be located and drill 2 holes for each chimney bracket. Secure the brackets with screws. Fix the V-flap to the air outlet and if using a vent pipe (not included) fix the vent pipe to the V-flap. Put the upper chimney into lower chimney. Then pulling out the upper chimney upwards. Adjust to reach the height required. There are 2 methods for installing the chimney cover: 1.
OPERATION Button Function Remarks Fan Off Turns off the fan Low Speed Starts the fan at low speed. Suitable for simmering and cooking which do not produce much steam Medium Speed Starts the fan at medium speed. Provides ideal ventilation for standard cooking High Speed Starts the fan at high speed. Ideal for when high density smoke or steam has been produced Lights On/Off Turns the lights on and off CLEANING AND MAINTENANCE Before cleaning, switch the unit off and disconnect the power.
MONTHLY CLEANING FOR METALLIC ANTI-GREASE FILTER IMPORTANT NOTE: Clean the filter every month; an excessive build-up of grease can become a fire hazard. The filter collects grease, smoke and dust, so the filter directly affects the efficiency of the cooker hood. If it’s not cleaned, the grease residue (potentially flammable) will saturate on the filter. Clean it with a soft nylon brush in a mild solution of warm water and a small amount of washing up liquid. Washing up liquid alone should not be used.
INSTALLING GREASE MESH FILTERS To install filters: 1. 2. 3. 4. Angle the filter into the slots at the back of the hood. Push the button on handle of the filter. Release the handle once the filter fits into position. Repeat to install both filters. CARBON FILTER (not supplied) Activated carbon filters can be used to trap odours. The activated carbon filter should be changed between three and six months according to use. The installation procedure of activated carbon filters is as below. 1.
BULB REPLACEMENT The bulb must be replaced by either the manufacturer, a service agent or similarly qualified persons. Always switch off the electricity supply before carrying out any operations on the appliance. When handling the bulb, make sure it has completely cooled down before making contact with the hands. When handling bulbs hold with a cloth or gloves to ensure perspiration does not come in contact with the bulb as this can reduce the life of the bulb. 1. Remove the grease filters. 2.
TROUBLESHOOTING FAULT Light on, but fan does not work CAUSE The fan blade is jammed. Both light and fan do not work Light bulb blown Power cord loose Replace the bulb with correct rating. Plug in to the power supply again. Excessive Vibration The fan blade is damaged. Switch off the unit. Repair to be carried out by qualified service personnel only. The fan motor is not fixed tightly. Switch off the unit. Repair to be carried out by qualified service personnel only.
PRODUCT FICHE Symbol Value Unit AEChood 36.41 kWh/a f 1.6 Fluid Dynamic Efficiency FDEhood 10.1 Energy Efficiency Index EEIhood 75.1 Measured airflow rate at the best efficiency QBEP 176.2 m3/h Measured air pressure at best efficiency point PBEP 118.3 Pa Maximum airflow Qmax 301.9 m3/h Measured electric power input at best efficiency point WBEP 57.
