USER MANUAL ANGLED BLACK GLASS TOUCH CONTROL COOKER HOOD eiQCHA90B/ eiQCHA90SS Thank you for choosing electriQ Please read this user manual before using this product and keep it safe for future reference. Visit our page www.electriQ.co.
CONTENTS SAFETY 3 PRODUCT OVERVIEW 5 VENTING OPTIONS 6 INSTALLATION 7 FILTER INFORMATION 11 OPERATION 12 CLEANING AND MAINTENANCE 13 TROUBLESHOOTING 14 TECHNICAL SPECIFICATION 15 SUPPORT 16 2
SAFETY PRECAUTIONS Whilst this product is compliant with all safety requirements, incorrect or inappropriate use can lead to both personal injury and potential damage to property. Please read the contents of this instruction booklet thoroughly before fitting or using this appliance. • The cooker hood must be installed in accordance with the installation instructions and all measurements followed. • All installation work must be carried out by a competent person or qualified electrician.
• The minimum distance between the surface of the hob and the lowest part of the hood should be at least 65cm. A distance of between 65cm and 75cm gives peak efficiency. • The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels. • When the hood is vented externally and used with appliances which burn fuel (e.g. gas, oil, wood) the area must be sufficiently ventilated to ensure safe operation.
PRODUCT OVERVIEW - PARTS SUPPLIED Description Illustration Qty.
EXTERNAL VENTING If you have an outlet to the outside, your cooker hood can be connected as shown in the diagram using any suitable extraction duct (enamel, aluminium, flexible pipe or inflammable material with an interior diameter of 150mm) can be used. An adaptor is supplied to enable you to connect your hood to pre-existing 120mm diameter ducting. If this is the chosen installation method consideration to the route of the vent pipe should be made prior to installation.
INSTALLATION 1. Before installation, ensure you have not connected the appliance to the mains supply. 2. The cooker hood should be placed at a distance of 65~75cm above the cooking plane for best effect. 3. Install the hanging screw on a suitable place once the installation height is fixed, and keep it in line. The fixed position of the inside chimney bracket is the place of chimney. Also install the safety hole in the wall. Total drill 8 holes and insert the Wall plug. 4.
5. The 2 x airflaps should be installed at this stage, as access is easier before the unit is wall mounted. On the top of the Hood Unit itself, where the air outlet vent is located, the 2 x flaps should be carefully installed, bending very slightly so the lugs at each end locate into the holes, enabling flaps to pivot upwards when the unit is in operation, opening up the outlet fully for the air to pass through.
NOTE: Remember not to fix the screw too tightly, so that later height adjustment can be done more easily. 9. Fix the chimney set into the chimney bracket and fix with 2 x screws (4mmx8mm), then fix the outer chimney bracket into wall with 2 x screws (4mm x 40mm), pull out the exhaust pipe to outside. 10. Pull up the inner chimney and fix it into inner chimney bracket with 2 x screws (4mm x 8mm). 11. Take out the Aluminum filter and fix the safety hole with 2 x screws (4mm x30mm).
12. Before usage, read all the instructions and make sure that the voltage (V) and the frequency (Hz) indicated on the identification plate (found inside the cooker hood) and all the data inside the appliance are exactly the same as the voltage and frequency in your home. Then plug the power lead into the power socket (or if connecting directly to the main via a switched spur, ensure the work is carried out by a competent, qualified person) and the cooker hood is then ready for use.
CARBON FILTER（OPTIONAL） Activated carbon filters should be used to trap odours (optional – available from the same stockist you purchased the hood from) and must be used if the hood is not vented to the outside. Reference: eiQCF110 Carbon Filter Pack– fits model eiQCHA90B, eiQCHA90SS In order to install the activated carbon filters, the aluminium filter should be removed first.
OPERATION Press “ 1. show ” button once and the lights will be turned on. The LCD will Press again to turn off. 2. Press “ ” button once; the hood works at LOW speed and LCD will display low speed. Press the speed button repeatedly to cycle through Low Medium and Fast speeds. If speed is pressed again after Fast speed. The fan will be turned off. 3. For Timer settings, press and hold the “ will be shown on LCD and Press “ ” button for 2 to 3 seconds; flashes; which represents the hour.
MAINTENANCE Before cleaning, switch the unit off and pull out the plug, or switch off at the relevant mains switch if the unit has been hard-wired in. Make sure the unit has no power being fed to it. REGULAR CLEANING Use a soft cloth moistened with warm mildly soapy water or household cleaning detergent. Never use metal pads, chemicals, abrasive material or a stiff brush to clean the unit.
TROUBLESHOOTING Fault Light on, but fan does not work Both light and fan do not work Excessive Vibration Suction performance not good Cause Solution The fan blade is jammed. The motor is damaged. Halogen light bulb blown Power cord loose The fan blade is damaged. The fan motor is not fixed tightly. The unit is not hung properly on the bracket. 1 Grease filters clogged? 2 Distance between the unit and the cooking plane too great. Switch off the unit.
INFORMATION FOR COOKER HOOD Symbol Value Model identification Annual Energy Consumption Time increase factor Fluid Dynamic Efficiency Energy Efficiency Index Measured airflow rate at the best efficiency Measured air pressure at best efficiency point Maximum airflow Measured electric power input at best efficiency point Nominal power of the lighting system Average illumination of the lighting system on the cooking surface Measured power consumption on standby mode Measured power consumption on off mode Sou
INFORMATION FOR DISMANTLING Do not dismantle the appliance in a way which is not shown in the user manual. The appliance could not be dismantled by user. At the end of life, the appliance should not be disposed of with household waste. Check with you Local Authority or retainer for recycling advice. electriQ UK SUPPORT www.electriQ.co.uk/support Call: 0871 984 4416 Office hours: 9AM - 5PM Monday to Friday www.electriQ.co.
