INSTALLATION AND USER MANUAL SLOPING BLACK GLASS COOKER HOOD eiQCHB60B eiQCHB90B Thank you for choosing your electriQ cooker hood. This instruction manual is designed to provide you with all required instructions related to the installation, use and maintenance of the appliance. In order to operate the unit correctly and safely, please read this instruction manual carefully before installation and usage.
CONTENTS SAFETY PRECAUTIONS 3 OPTIONS FOR VENTILATION 5 UNPACKING YOUR APPLIANCE 5 PRODUCT OVERVIEW 6 DIAGRAM 7 INSTALLATION 8 OPERATION 12 MAINTENANCE 14 CARBON FILTERS (OPTIONAL) 14 LIGHT BULB REPLACEMENT 15 TROUBLESHOOTING 15 TECHNICAL INFORMATION 16 SUPPORT 18 2
SAFETY PRECAUTIONS Whilst this product is compliant with all safety requirements, incorrect or inappropriate use can lead to both personal injury and potential damage to property. Please read the contents of this instruction booklet thoroughly before fitting or using this appliance. • The cooker hood must be installed in accordance with the installation instructions and all measurements followed. • All installation work must be carried out by a competent person or qualified electrician.
• The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels. • When the hood is vented externally and used with appliances which burn fuel (e.g. gas, oil, wood) the area must be sufficiently ventilated to ensure safe operation. Fresh air must be allowed to freely enter the room to prevent a partial vacuum. • A partial vacuum can starve the heating appliance of oxygen, impairing combustion.
OPTIONS FOR VENTILATION This hood can be set up for either external venting or recirculation of the air. setup should be decided before commencing installation. The type of EXTERNAL VENTING If you have an outlet to the outside, your cooker hood can be connected as shown in the diagram using the flexible exhaust pipe (supplied). Alternatively, any suitable extraction duct (enamel, aluminium, flexible pipe or non-flammable material with an interior diameter of 150mm) can be used.
PRODUCT OVERVIEW - PARTS SUPPLIED Description Illustration Qty.
DIAGRAMS eiQCHB60B eiQCHB90B 7
INSTALLATION 1. Before installation, ensure you have not connected the appliance to the mains supply. 2. The base of the cooker hood should be placed at a distance of 65~75cm above the cooking plane for best effect. 3. Install the hanging screws on a suitable wall once the installation height is decided, ensuring they are level. The fixed position of the inside chimney bracket is the place of chimney. Also install the safety hole in the wall. In total 8 holes should be drilled and wall plugs inserted. 4.
6. Hang on the cooker hood on to the two screws previously installed. 7. If venting externally attach the vent pipe onto the one-wayvalve, and fix the pipe on the valve using the cable tie. The adaptor can be used at this stage, if you already have existing smaller diameter venting in place to connect. 8. Adjust the length of the chimney to around the required height (Fine adjustment can be done later. Then install plate I on the chimney using two screws (4mm x 8mm).
. Pull up the inner chimney and fix it into inner chimney bracket with 2 x screws (4mm x 8mm). 11. Remove the Aluminium filter and fix to the wall with 2 x screws (4mm x30mm) through the safety holes. 12. Before usage, read all the instructions and make sure that the voltage (V) and the frequency (Hz) indicated on the identification plate (found inside the cooker hood) and all the data inside the appliance are exactly the same as the voltage and frequency in your home.
CARBON FILTER（OPTIONAL） Activated carbon filters should be used to trap odours (optional – available from the same stockist you purchased the hood from) and must be used if the hood is not vented to the outside. Reference: eIQCF160 Carbon Filter Pack In order to install the activated carbon filters, the aluminium filter should be removed first. Press the lock and pull it downward as below: Put the activated carbon filter onto the end of the motor unit and turn it in anti-clockwise direction.
OPERATION POWER BUTTON While the hood is turned off, press the POWER button to start the hood at the previously used speed. While the hood is turned on, press the POWER button to turn the hood off. LAMP BUTTON Press the LAMP button to illuminate the display. the display. Press the LAMP button again to turn off Note: The backlight will turn off after 15 seconds without any operation. SPEED BUTTON With the fan funning, press the SPEED button to cycle between the three fan speeds: Low, Medium and High.
REMOTE CONTROL LAMP Press the button to turn on the backlight. Press the button again to turn off the backlight. TURN ON / INCREASE FAN SPEED With the hood turned off, press the + button to start the fan at low speed. While the fan is running, press the + button to increase the fan speed. TURN OFF / DECREASE FAN SPEED While the fan is running at high or medium speed, press the - button to decrease the fan speed. While the fan is running at low speed, press the - button to turn off the hood.
MAINTENANCE Before cleaning, switch the unit off and pull out the plug, or switch off at the relevant mains switch if the unit has been hard-wired in. Make sure the unit has no power being fed to it. REGULAR CLEANING Use a soft cloth moistened with hand-warm mildly soapy water or household cleaning detergent. Never use metal pads, chemicals, abrasive material or a stiff brush to clean the unit.
LIGHT REPLACEMENT Important: The light fitting must be replaced by the manufacturer, its service agent or similarly qualified persons. Always switch off the electricity supply before carrying out any operations on the appliance. When handling the light fitting, make sure it has completely cooled down before any direct contact to hands. • Switch the unit off and disconnect the power. • Wait until the light fitting has cooled down before replacement.
TECHNICAL INFORMATION Symbol Value Model identification Annual Energy Consumption Unit eiQCHB60B AEChood 97.3 f 1,2 FDEhood 21.9 EEIhood 71.9 QBEP 463.8 m3/h Measured air pressure at best efficiency point PBEP 360 Pa Maximum airflow at boost position Qmax 796.1 m3/h Maximum airflow Qmax 627.6 m3/h W BEP 212.
Symbol Value Model identification Annual Energy Consumption Unit eiQCHB90B AEChood 93.9 f 1,1 FDEhood 24.8 EEIhood 66.5 QBEP 537.6 m3/h Measured air pressure at best efficiency point PBEP 370 Pa Maximum airflow at boost position Qmax 836.4 m3/h Maximum airflow Qmax 632.1 m3/h W BEP 223.
INFORMATION FOR DISMANTLING Do not dismantle the appliance in a way which is not shown in the user manual. The appliance could not be dismantled by user. At the end of life, the appliance should not be disposed of with household waste. Check with your Local Authority or retailer for recycling advice. electriQ UK SUPPORT www.electriQ.co.uk/support Call: 0871 984 4416 Office hours: 9AM - 5PM Monday to Friday www.electriQ.co.
