User Manual Angled 60cm Cooker Hood eiQCHC60W Thank you for choosing electriQ Please read this user manual before using this product and keep it safe for future reference. Visit our page www.electriQ.co.
CONTENTS SAFETY 3 PRODUCT OVERVIEW 5 VENTING OPTIONS 6 INSTALLATION 7 FILTER INFORMATION 11 OPERATION 12 CLEANING AND MAINTENANCE 12 LIGHT REPLACEMENT 13 TROUBLESHOOTING 14 PRODUCT FICHE 15 SUPPORT 16 2
SAFETY PRECAUTIONS Whilst this product is compliant with all safety requirements, incorrect or inappropriate use can lead to both personal injury and potential damage to property. Please read the contents of this instruction booklet thoroughly before fitting or using this appliance. • The cooker hood must be installed in accordance with the installation instructions and all measurements followed. • All installation work must be carried out by a competent person or qualified electrician.
• The minimum distance between the surface of the hob and the lowest part of the hood should be at least 65cm. A distance of between 65cm and 75cm gives peak efficiency. • The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels. • When the hood is vented externally and used with appliances which burn fuel (e.g. gas, oil, wood) the area must be sufficiently ventilated to ensure safe operation.
PRODUCT OVERVIEW - PARTS SUPPLIED Description Illustration Qty.
EXTERNAL VENTING If you have an outlet to the outside, your cooker hood can be connected as shown in the diagram using any suitable extraction duct (enamel, aluminium, flexible pipe or inflammable material with an interior diameter of 150mm) can be used. An adaptor is supplied to enable you to connect your hood to pre-existing 120mm diameter ducting. If this is the chosen installation method consideration to the route of the vent pipe should be made prior to installation.
INSTALLATION 1. Before installation, ensure you have not connected the appliance to the mains supply. 2. The cooker hood should be placed at a distance of 65~75cm above the cooking plane for best effect. 65 75 Pic 1 3. Install the hanging screw on a suitable place once the installation height is fixed, and keep it in line. The fixed position of the inside chimney bracket is the place of chimney. Also install the safety hole in the wall. Total drill 8 holes and insert the Wall plug. 4.
5. The 2 x airflaps should be installed at this stage, as access is easier before the unit is wall mounted. On the top of the Hood Unit itself, where the air outlet vent is located, the 2 x flaps should be carefully installed, bending very slightly so the lugs at each end locate into the holes, enabling flaps to pivot upwards when the unit is in operation, opening up the outlet fully for the air to pass through.
8. Adjust the height of the chimney to approximately the required height. Then install plate I on the chimney. Two screws (4mm x 8mm) are used. i Put the inner chimney into the outer chimney. Then pull the inner chimney upwards. Adjust to reach the approximate height required. Fine height adjustment is done later. ii. Install plate I on the chimney NOTE: Remember not to fix the screw too tightly, so that later height adjustment can be done more easily. 9.
11. Take out the Aluminum filter and fix the safety hole with 2 x screws (4mm x30mm). PIC 9 12. Before usage, read all the instructions and make sure that the voltage (V) and the frequency (Hz) indicated on the identification plate (found inside the cooker hood) and all the data inside the appliance are exactly the same as the voltage and frequency in your home.
CARBON FILTER（OPTIONAL） Activated carbon filters should be used to trap odours (optional – available from the same stockist you purchased the hood from) and must be used if the hood is not vented to the outside. Reference: eiQCF110 Carbon Filter Pack– fits model eiQCHC60W In order to install the activated carbon filters, the aluminium filter should be removed first.
OPERATION Push button for model eiQCHC60W 1. 2. 3. 4. 5. Push stop button, and the motor will stop. Push the Low button, and the motor runs at low speed. Push the high button, and the motor runs at mid speed. Push the High button, and the motor runs at high speed. Push the light button and the two lights will come on. Push it again and the light will turn off.
Remove the filter as shown in the Installation section. Clean it with a soft nylon brush in a mild solution of warm water and a small amount of washing up liquid. Washing up liquid alone should not be used. After cleaning, allow the filter to drain and then dry thoroughly. The grease filter may also be dishwasher cleaned; using a 60°C programme, with the filter upright (short sides upright) in the lower basket.
TROUBLESHOOTING FAULT CAUSE SOLUTION The fan blade is jammed. The motor is damaged. Both light and Halogen light bulb blown fan do not work Power cord loose The fan blade is damaged. The fan motor is not Excessive fixed tightly. Vibration The unit is not hung properly on the bracket. 1 Grease filters clogged? Suction 2 Distance between performance the unit and the not good cooking plane too great. Light on, but fan does not work Switch off the unit.
PRODUCT FICHE Symbol Value eiQCHC60W Model identification Annual Energy Consumption Unit AEChood 61.5 Time increase factor f 1.2 Fluid Dynamic Efficiency Energy Efficiency Index Measured airflow rate at the best efficiency FDEhood 22.8 EEIhood 67.6 QBEP 314.8 m3/h Measured air pressure at best efficiency point PBEP 349 Pa Maximum airflow Qmax 596.2 m3/h W BEP 133.7 W WL 4.
INFORMATION FOR DISMANTLING Do not dismantle the appliance in a way which is not shown in the user manual. The appliance could not be dismantled by user. At the end of life, the appliance should not be disposed of with household waste. Check with you Local Authority or retainer for recycling advice. electriQ UK SUPPORT www.electriQ.co.uk/support Call: 0330 390 3061 Office hours: 9AM - 5PM Monday to Friday www.electriQ.co.
