USER MANUAL ANGLED GLASS AND STEEL DESIGNER CHIMNEY COOKER HOOD eiQCHFGBSS60/ eiQCHFGBSS90 Thank you for choosing electriQ Please read this user manual before using this product and keep it safe for future reference. Visit our page www.electriQ.co.
CONTENTS SAFETY 3 PRODUCT OVERVIEW 5 VENTING OPTIONS 6 INSTALLATION 7 FILTER OPTIONS 13 OPERATION 14 CLEANING AND MAINTENANCE 15 LIGHT REPLACEMENT 16 TROUBLESHOOTING 16 PRODUCT FICHE 17 SUPPORT 19 2
SAFETY PRECAUTIONS Whilst this product is compliant with all safety requirements, incorrect or inappropriate use can lead to both personal injury and potential damage to property. Please read the contents of this instruction booklet thoroughly before fitting or using this appliance. • The cooker hood must be installed in accordance with the installation instructions and all measurements followed. • All installation work must be carried out by a competent person or qualified electrician.
• The plug must be accessible after installation for isolation in case of an emergency – or an appropriate fused switch if the unit is hard-wired to the mains via a spur. • The minimum distance between the surface of the hob and the lowest part of the hood should be at least 65cm. A distance of between 65cm and 75cm gives peak efficiency. • The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels.
PRODUCT OVERVIEW - PARTS SUPPLIED Description Illustration Qty.
EXTERNAL VENTING If you have an outlet to the outside, your cooker hood can be connected as shown in the diagram using any suitable extraction duct (enamel, aluminium, flexible pipe or inflammable material with an interior diameter of 150mm) can be used. An adaptor is supplied to enable you to connect your hood to pre-existing 120mm diameter ducting. If this is the chosen installation method consideration to the route of the vent pipe should be made prior to installation.
UNPACKING YOUR APPLIANCE • Please take great care when unpacking; a sharp blade should not be used to open the box, as it may go deep enough inside to damage components. Components damaged or marked by careless unpacking are not covered under the guarantee. • Carefully unpack the contents and check against the section below (Parts) and the next section (Product overview). • Packaging materials should be recycled in accordance with local regulations INSTALLATION 1.
3. Insert the glass into the panel glove of the cooker hood, then use 4 screws (4 x 25mm), inserting them through the 4 x rubber cushions to fix the glass into the cooker hood (see diagrams). 4. The 2 x air flaps should be installed at this stage, as access is easier before the unit is wall mounted.
5. Attach the exhaust pipe onto the outlet as shown below, and fix the pipe on the outlet by cable tie. The adaptor can be used at this stage, if you already have existing smaller diameter venting in place to connect. 6. Drill 3 holes to accommodate the wall bracket. Screw and tighten the wall bracket onto the wall with the screws (4mm x 40 mm) and wall plugs provided. Wall plug Screw (4mm x 40mm) Wall bracket 7． Hang the appliance onto the wall bracket.
8. Put the inner chimney on the outer chimney. Install plate I on the chimney by two screws (4 mm x 8mm). Drill holes on the wall to accommodate plate I. NOTE: Remember not to fix the screws (4 mm x 8mm) too tightly; 1mm loose is recommended, so that later height adjustment can be done more easily.
9. Drill 2 holes to accommodate plate II. Screw and tighten the plate II onto the wall with the screws (4mm x 40 mm) and wall plugs provided. Note: Plate II is used to fix the chimney. The below diagram is for reference. Fixing the chimney to wall plate is done at the end of installation.
10. Put the installed chimneys on the cooker hood. Fix the Plate I to the wall by using 2 (4mm x 40 mm) screws and wall plugs. Pull out extensible pipe till it feeds through the hole on the wall. Lift the inner chimney onto the plate II, fix the inner chimney to the plate II by using 2 screws (4mm x 8mm). After installation, make sure that the extractor is level to avoid grease collection at one end. √ X 11.
CARBON FILTER（OPTIONAL） Activated carbon filters should be used to trap odours (optional – available from the same stockist you purchased the hood from) and must be used if the hood is not vented to the outside. reference: eiQCF110 (Carbon Filter Pack of 2 – fits both 60cm and 90cm models) In order to install the activated carbon filters, the aluminium filter should be removed first.
OPERATION There are five buttons: (Low), (Mid), (High), (Light), (Power). 1. After connecting the hood, the indicator light will turn on and the hood will enter standby mode. 2. Power on: Press power button once, and the power indicator light will be turn on, the hood will automatically begin at low speed. The low speed indicator light will be on. Press the power button again to turn the unit off. 3. Press lamp button off once; lights will be turned on. The lamp indicator will turn .
MAINTENANCE Before cleaning, switch the unit off and pull out the plug, or switch off at the relevant mains switch if the unit has been hard-wired in. Make sure the unit has no power being fed to it. I. Regular Cleaning Use a soft cloth moistened with hand-warm mildly soapy water or household cleaning detergent. Never use metal pads, chemical, abrasive material or a stiff brush to clean the unit.
LIGHT REPLACEMENT IMPORTANT: The light fitting must be replaced by the manufacturer, its service agent or similarly qualified persons LED lamp: 1. Use the correct light: 2 x 1.5W LED. 2. Carefully take out the lamp with a suitable tool. 3. Change the lamp. TROUBLESHOOTING Fault Light on, but fan does not work Both light and fan do not work Cause The fan blade is jammed. The motor is damaged. Light blown Solution Power cord loose Plug in to the power supply again. Switch off the unit.
PRODUCT FICHE Symbol Value eiQCHFGBSS60 eiQCHFGBSS90 Model identification Annual Energy Consumption Time increase factor Fluid Dynamic Efficiency Fluid Dynamic Efficiency class Energy Efficiency Index Energy Efficiency class Measured airflow rate at the best efficiency Measured air pressure at best efficiency point Maximum airflow Air flow at working point (highest setting) Air flow at working point (lowest setting) Measured electric power input at best efficiency point Nominal power of the lighting syste
Grease Filtering Efficiency (GFE hood) class Measured power consumption on standby mode Measured power consumption on off mode Sound power level (Highest setting) Sound power level (Lowest setting) Class E PS 0.53- W PO 0.38 W LWA 69 dB LWA 65 dB The following shows how to reduce total environmental impact (e.g. energy use) of the cooking process). (1) Install the cooker hood in a proper place where there is efficient ventilation.
INFORMATION FOR DISMANTLING Do not dismantle the appliance in a way which is not shown in the user manual. The appliance could not be dismantled by user. At the end of life, the appliance should not be disposed of with household waste. Check with you Local Authority or retainer for recycling advice. electriQ UK SUPPORT www.electriQ.co.uk/support Call: 03303903061 Office hours: 9AM - 5PM Monday to Friday www.electriQ.co.
