USER MANUAL COOKER HOOD eiQCHIM60SC eiQCHIM60WH eiQCHIM60BL eiQCHIM90SC eiQCHIM90BL Thank you for choosing electriQ. Please read this user manual before using this Cooker Hood and keep it safe for future reference. Visit our page www.electriQ.co.
CONTENTS SAFETY PRECAUTIONS 3 OPTIONS FOR VENTILATION 5 UNPACKING YOUR APPLIANCE 5 PRODUCT OVERVIEW 6 INSTALLATION 7 OPERATION 12 MAINTENANCE 13 CARBON FILTERS (OPTIONAL) 13 LIGHT BULB REPLACEMENT 14 TROUBLESHOOTING 15 TECHNICAL INFORMATION 16 MANUFACTURER SUPPORT 17 2
SAFETY PRECAUTIONS Whilst this product is compliant with all safety requirements, incorrect or inappropriate use can lead to both personal injury and potential damage to property. Please read the contents of this instruction booklet thoroughly before fitting or using this appliance. • The cooker hood must be installed in accordance with the installation instructions and all measurements followed. • All installation work must be carried out by a competent person or qualified electrician.
• The minimum distance between the surface of the hob and the lowest part of the hood should be at least 65cm. A distance of between 65cm and 75cm gives peak efficiency. • The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels. • When the hood is vented externally and used with appliances which burn fuel (e.g. gas, oil, wood) the area must be sufficiently ventilated to ensure safe operation.
OPTIONS FOR VENTILATION This hood can be set up for either external venting or recirculation of the air. The type of setup should be decided before commencing installation. EXTERNAL VENTING If you have an outlet to the outside, your cooker hood can be connected as shown in the diagram using the flexible exhaust pipe (supplied). Alternatively any suitable extraction duct (enamel, aluminium, flexible pipe or inflammable material with an interior diameter of 150mm) can be used.
PARTS SUPPLIED Description Illustration Qty.
INSTALLATION 1. Before installation, ensure you have not connected the appliance to the mains supply. 2. The cooker hood should be placed at a distance of 70~80cm above the cooking plane for best effect. Wall plug Screw (4mm x 30mm) 3. Drill 3 holes to accommodate the wall bracket. Screw and tighten the wall bracket onto the wall with the screws (4mm x 30 mm) and wall plugs provided. 4. Hang the appliance onto the wall bracket. 5.
6. Plate I and II are used to fix the chimney onto the wall. Put the inner chimney into the outer chimney. Mark the position for plate II. Then pull the inner chimney upwards to the desired height, and mark the position of plate I. 7. Drill holes to accommodate plate I & II, and insert wall plugs. 8. Fix plate II on the wall using two screws (4mm x 30mm). 9. The 2 x air flaps should be installed at this stage, as access is easier before the unit is wall mounted.
10. Put the chimney onto the cooker hood. Attach plate II onto the outer chimney. Lift the inner chimney to the desired height, and attach plate I onto it. There are two methods for attaching the plates to the chimney after the plates have been attached to the wall. a. Fix the plates to the wall using two screws (4mm x 30mm) and wall plugs. Hang the chimney on the plates using the hooks in the side of the chimney. (Pic 1) b. Fix the plates to the wall using two screws (4mm x 30mm) and wall plugs.
CARBON FILTER (OPTIONAL) Activated carbon filters can be used to trap odours (optional) – and must be used if the hood is not vented to the outside. They are available from the same stockist you purchased the hood from. Part Number: eiQTMCARBONCHIM (Carbon Filter Pack of 2) In order to install the activated carbon filter, the metallic anti-grease filter should be detached first. Press the lock and pull it downward.
OPERATION Operation of your hood is extremely simple. There are essentially 3 controls: Power On/Off; Fan Speeds (3 separate buttons) and Illumination.
MAINTENANCE Before cleaning, switch the unit off and pull out the plug, or switch off at the relevant mains switch if the unit has been hard-wired in. Make sure the unit has no power being fed to it. I. REGULAR CLEANING Use a soft cloth moistened with hand-warm mildly soapy water or household cleaning detergent. Never use metal pads, chemicals, abrasive material or a stiff brush to clean the unit.
IV. LIGHT BULB REPLACEMENT This hood is fitted with an LED light unit, which under normal operation can last the lifetime of the hood. In the event that it does fail, replacement light units are available from the same retailer the hood was purchased from. Before changing the fitting, ensure the hood is turned off and the power is removed by either unplugging the unit or switching off at the pole switch (if installed) before attempting to change the bulb.
TROUBLESHOOTING Fault Light on, but fan does not work Both light and fan do not work Cause The fan blade is jammed. The motor is damaged. Light bulb blown Power cord loose The fan blade is damaged. Excessive Vibration Suction performance not good The fan motor is not fixed tightly. The unit is not hung properly on the bracket. 1 Grease filters clogged 2 Distance between the unit and the cooking plane too great. 14 Solution Switch off the unit.
TECHNICAL INFORMATION Value Value eiQCHIM60SC eiQCHIM60BL eiQCHIM60WH eiQCHIM90SC eiQCHIM90BL AEChood 35.99 37.51 f 1.655 1.68 FDEhood 9.95 8.81 Class E Class E Symbol Model identification Annual Energy Consumption Time increase factor Fluid Dynamic Efficiency Fluid Dynamic Efficiency class Energy Efficiency Index EEIhood Energy Efficiency class 75.4 77.
INFORMATION FOR DISMANTLING Do not dismantle the appliance in a way which is not shown in the user manual. The appliance could not be dismantled by user. At the end of life, the appliance should not be disposed of with household waste. Check with you Local Authority or retainer for recycling advice. electriQ UK SUPPORT www.electriQ.co.uk/support www.electriQ.co.
