INSTALLATION AND USER MANUAL COOKER HOOD 60cm hood Stainless steel eiQCURV60SC Black eiQCURV60BL white eiQCURV60WH 90cm hood eiQCURV90SC eiQCURV90BL eiQCURV90WH Please read this manual before using or installing the cooker hood and keep it safe for future reference. Visit our page www.electriQ.co.
CONTENTS SAFETY 3 PARTS LIST 5 INSTALLATION 6 EXHAUST DUCT INSTALLATION 11 OPERATION 12 BULB REPLACEMENT 13 FILTER INFORMATION 14 GLASS CANOPY MAINTENANCE 15 CLEANING AND MAINTENANCE 16 TROUBLESHOOTING 17 TECHNICAL SPECIFICATION 18 SUPPORT 19 PRODUCT FICHE 20 2
IMPORTANT SAFETY INFORMATION Please read this instruction manual carefully and retain for future reference. It contains important information concerning the safe operation, installation and maintenance of the appliance. • There must be adequate ventilation of the room when the hood is used at the same time as appliances burning gas or other fuels. • This cooker hood is only designed for domestic use, and should not be used in a commercial environment.
• Cleaning and user maintenance must not be carried out by children without supervision. • When the hood is being maintained, cleaned or filters changed, make sure it is switched off at the mains supply. • The exterior of the hood should be cleaned with mild detergent on a warm damp sponge or cloth. • The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels. • Regulations concerning the discharge of air have to be fulfilled.
PARTS DESCRIPTION ILLUSTRATION Cooker Hood QTY 1 Chimney Sections 2 Chimney bracket 2 Hood Installation Plate 1 Screw (ST5*50) 7 Wall plug 7 Screw (ST4.2*9.
INSTALLATION DIAGRAM Upper Chimney Bracket Lower Chimney Bracket Hood Installation Plate 6
OPTIONS FOR VENTILATION This hood can be set up for either external venting or recirculation of the air. The type of setup should be decided before commencing installation. EXTERNAL VENTING A 150mm diameter flexible pipe is provided which allows the cooking odours to be extracted outside. If this is the chosen installation method consideration to the route of the vent pipe should be made. The unit is also provided with an adaptor allowing pre-existing 120mm ducting to be used to vent the unit.
INSTALLATION BEFORE INSTALLING YOUR HOOD: • Unpack the hood and check that all functions are working. Ensure that the voltage (V) and the frequency (Hz) indicated on the serial plate match the voltage and frequency at the installation site. • Check that the area behind the installation surface to be drilled is clear of any electrical cables or pipes, etc. • The surfaces of the hood are very easily damaged during installation if grazed or knocked by tools.
1. Before installation, ensure you have not connected the appliance to the mains supply. 2. The cooker hood should be placed at a distance of 65~75cm above the cooking plane for best effect. • After confirming the cooker hood height, measure the position of the holes for hanging the hood and inside chimney bracket. Drill 4 φ8 holes, 2 for inside chimney bracket and 2 for hanging the hood, and keep the hood level. The chimney bracket should be secured at the highest place of chimney.
• • Dress the inside chimney into the outside chimney. See Pic 4. Make the hood hang on the wall in the fixed position, adjusting the cooker hood position, fix the cooker hood with safety screws. • The two safety vents are positioned on the back housing, with diameter of 6mm.See Pic 5.
EXHAUST DUST INSTALLATION The following rules must be strictly followed to obtain optimal air extraction: • Keep expansion pipe short and straight. • Do not reduce the size or restrict expansion pipe. • When using expansion pipe always install the pipe pulled taut to minimize pressure loss. • Failure to observe these basic instructions will reduce the performance and increase noise levels of the cooker hood. • Any installation work must be carried out by a qualified electrician or competent person.
OPERATION Operation of your hood is extremely simple. There are essentially 3 controls: Power Off; Fan Speed (3 separate buttons) and Illumination.
REPLACING THE BULB This hood is fitted with an LED light unit, which under normal operation can last the lifetime of the hood. In the event that it does fail, replacement light units are available from the same retailer the hood was purchased from. Before changing the fitting, ensure the hood is turned off and the power is removed by either unplugging the unit or switching off at the pole switch (if installed) before attempting to change the bulb.
INSTALLING THE CARBON FILTER (OPTIONAL) 1. Remove the grease filters from the underside of the hood. 2. The carbon filters are located at either end of the motor. TO FIT: Locate the filter on the peg on the side of the motor. Rotate the filter clockwise onto the motor housing; TO REMOVE: Rotate the filter anti-clockwise until it is unscrewed. WARNING: The carbon filter cannot be washed or recycled. It should be replaced after approximately 2-3 months of use.
REMOVAL AND REFITTING OF THE GLASS CANOPY WARNING: Components within the appliance may have sharp edges. When attempting to remove or refit the glass, gloves should be worn to avoid scratches and cuts. The glass canopy is held into position using four screws, spacers and decorative washers. Remove the four screws, spacers and decorative washers from the glass canopy, ensuring the canopy is suitably supported. Two people should then lift the canopy off the hood, retaining the fittings removed for re fitting.
CLEANING AND MAINTENANCE Disconnect range hood from power supply before cleaning or servicing. 1. Clean the hood surface frequently using mild detergent and a warm damp sponge or cloth. 2. Do not use harsh alkalis or abrasives. 3. Avoid the use of scouring powers or dishwasher compounds. 4. If the optional carbon filter is being used, these cannot be cleaned and require replacing every 2-3 months depending on frequency of use. They are available from the retailer who supplied your hood.
TROUBLESHOOTING Fault Light on, but fan does not work Both light and fan do not work Excessive Vibration Suction performance not good Cause Solution The fan blade is jammed. Switch off the unit. Repair to be carried out by qualified service personnel only. The motor is damaged. Power cord loose Plug in to the power supply again. The fan blade is damaged. Switch off the unit. Repair to be carried out by qualified service personnel only. The fan motor is not fixed tightly. Switch off the unit.
SPECIFICATION Voltage 220-240V~50Hz Rated Power 108W Lighting Power 2 X 1.5W Motor Power 105W Diameter of air tube 150mm Air flow 400m /h3 Noise ≤6 dB5 The following shows how to reduce total environmental impact (e.g. energy use) of the cooking process). (1) Install the cooker hood in a proper place where there is efficient ventilation. (2) Clean the cooker hood regularly so as not to block the airway. (3) Remember to switch off the cooker hood light after cooking.
electriQ UK SUPPORT www.electriQ.co.uk/support Call: 0871 984 4416 Office hours: 9AM - 5PM Monday to Friday www.electriQ.co.uk Unit J6, Lowfields Business Park Lowfields Way, Elland West Yorkshire, HX5 9DA Recycling facilities are now available for all customers at which you can deposit your old electrical products. Customers will be able to take any old electrical equipment to participating sites run by their local councils.
PRODUCT FICHE Model Identification eiQCURV60SC eiQCURV60BL eiQCURV90SC eiQCURV90BL eiQCURV60WH eiQCURV90WH Symbol Value Unit AEChood 53.2 kWh/A Annual Energy Consumption Standard Annual Energy kWh/a Consumption SAEChood 65.0 Time increase factor F 1.6 Fluid Dynamic Efficiency FDEhood 11.0 Energy Efficiency Index EEIhood 81.8 Measured air flow rate at m3/h best efficiency point QBEP 244.2 Measured air pressure at Pa best efficiency point PBEP 142 Maximum air flow Qmax 423.
