USER MANUAL COOKER HOOD eiQCURV60/90EN eiQCURV60/90ENBL Please read this manual before using or installing the cooker hood and keep it safe for future reference. Visit our page www.electriQ.co.
CONTENTS IMPORTANT SAFETY INFORMATION 3 PARTS 5 INSTALLATION OF FLAPS 6 EXTERNAL VENTILLATION 7 INSTALLATION 7 EXHAUST INSTALLATION 11 OPERATION 12 GREASE MESH FILTERS 12 CARBON FILTER 13 REPLACING THE BULB 14 CLEANING AND MAINTENANCE 15 TROUBLESHOOTING 16 SPECIFICATION AND SUPPORT 17 PRODUCT FICHE 18 2
IMPORTANT SAFETY INFORMATION Please read this instruction manual carefully and retain for future reference. It contains important information concerning the safe operation, installation and maintenance of the appliance. • There must be adequate ventilation of the room when the hood is used at the same time as appliances burning gas or other fuels. • This cooker hood is only designed for domestic use, and should not be used in a commercial environment.
sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. • Children must not play with the appliance. • Cleaning and user maintenance must not be carried out by children without supervision. • When the hood is being maintained, cleaned or filters changed, make sure it is switched off at the mains supply.
PARTS DESCRIPTION ILLUSTRATION QTY Cooker Hood 1 Glass Canopy 1 Chimney Sections (Pair) 1 Outlet 1 Air Flap 2 Chimney bracket 1 Canopy Anti vibration ring 4 Canopy Mounting washer 4 Bolt (M4*20) 4 Screw (ST4*40) 2 Screw (ST4*30) 4 Wall plug 6 Screw (ST4*8) 4 Exhaust Adaptor 1 5
INSTALLATION OF THE FLAPS The 2 air flaps should now be installed on the top of the unit, as access is easier before the unit is wall mounted. The flaps should be carefully installed, bending them slightly so the lugs at each end locate into the holes in the outlet vent. When the unit is in operation the flaps pivot upwards to allow airflow. Please note: Ensure the small lugs at each end of each flap locate into the holes on the housing and not the grooves above them.
OPTIONS FOR VENTILATION This hood can be set up for either external venting or recirculation of the air. The type of setup should be decided before commencing installation. EXTERNAL VENTING If you have an outlet leading outside, your cooker hood can be connected as shown in the diagram using a flexible exhaust pipe. Alternatively, any suitable extraction duct (enamel, aluminium, flexible pipe or inflammable material with an interior diameter of 120/150mm) can be used.
INSTALLATION • Unpack the hood and check that all functions are working. Ensure that the voltage (V) and the frequency (Hz) indicated on the serial plate match the voltage and frequency at the installation site. • Check that the area behind the installation surface is clear of any electrical cables or pipes, etc to avoid damage when drilling. • The surfaces of the hood can be very easily damaged during installation. Take care with tools to protect the surfaces during installation.
1. Before installation, ensure you have not connected the appliance to the mains supply. 2. The cooker hood should be placed at a distance of 65~75cm above the cooking plane for best effect. 3. After confirming the height of the cooker hood measure the position of the holes inside and outside of the chimney bracket for hanging the hood. 4. Drill 4 holes, 2 for the inner chimney bracket and 2 for hanging the hood, and keep the hood level. The inner chimney bracket should be secured at the highest point.
6. Place the glass canopy on to the hood, aligning the screw holes. Place the anti-vibration rings into the 4 holes before securing the glass canopy into place by tightening the 4 bolts (M4*20) through the mounting rings into the hood. 7. Then fix the outlet on the hood and attach the adaptor. 8. Hang the hood on the wall in the desired final position. 9. Once the hood is positioned correctly, fix the unit to the wall using 2 x ST4*30 screws and wall plugs through the fixing holes.
EXHAUST INSTALLATION The following rules must be strictly followed to obtain optimal air extraction: • Keep the expansion pipe short and straight. • Do not reduce the size or restrict expansion pipe. • When using an expansion pipe always install the pipe pulled taut to minimize pressure loss. • Failure to observe these basic instructions will reduce the performance and increase noise levels of the cooker hood. • Any installation work must be carried out by a qualified electrician or competent person.
USING YOUR COOKER HOOD STOP LOW MEDIUM HIGH LIGHTS ON/OFF STOP Turns off the motor LOW Will extract at low speed MEDIUM Will extract at medium speed HIGH Will extract at high speed LIGHTS Turn the light on and off GREASE MESH FILTERS The mesh filters can be cleaned by hand. Soak them for 3 - 4 minutes in warm water with a grease-loosening detergent. Brush gently with a soft brush. To avoid damage, do not apply unnecessary pressure. Leave to dry naturally out of direct sun light.
CARBON FILTER (Not Supplied) Activated carbon filters can be used to trap odours. Normally the activated carbon filter should be changed every three or six months according to your cooking habit. Grease filters are available from the retailer and directly from the manufacturer under stock code: eiQCF152 for eiQCURV60EN/ENBL;eiQCF15290 for eiQCURV90EN/ ENBL. The installation procedure is as below. 1. Remove the grease filter. 2. Unclip the wire from the reverse of the grease filter. 3.
REPLACING THE BULB 1. Switch off the extractor hood and ensure it is also switched off at the mains supply. 2. Remove the grease filters. 3. Disconnect the wiring connector on the lead running from the lamp holder. 4. Replace the holder and lamp with an identical unit available from the retailer/manufacturer. NOTE: Remember to switch on at the mains once installation is completed and the hood has been fully reassembled.
CLEANING AND MAINTENANCE Disconnect range hood from power supply before cleaning or servicing. 1. 2. 3. 4. 5. 6. Clean the hood surface frequently using mild detergent and a warm damp sponge or cloth. Do not use harsh alkalis or abrasives. Avoid the use of scouring powers or dishwasher compounds. If the optional carbon filter is being used, these cannot be cleaned and require replacing every 2-3 months depending on frequency of use. They are available from the retailer who supplied your hood.
TROUBLESHOOTING Fault Light on, but fan does not work Both light and fan do not work Grease or oil leaking from the underside of the hood Cause The fan blade is jammed. The motor is damaged. Solution Switch off the unit. Repair to be carried out by qualified service personnel only. Replace the lamp with correct rating. Plug in to the power supply again. Light has blown. Power cord loose.
electriQ UK Support Office hours: 9AM - 5PM Monday to Friday 0330 390 3061 www.electriQ.co.uk Unit J6, Lowfields Business Park Lowfields Way, Elland West Yorkshire, HX5 9DA PRODUCT DISPOSAL Do not dispose this product as unsorted municipal waste. Collection of such waste must be handled separately as special treatment is necessary. Recycling facilities are now available for all customers at which you can deposit your old electrical products.
PRODUCT FICHE eiQCURV60EN/ENBL 18
eiQCURV90EN/ENBL 19
