USER MANUAL ISLAND COOKER HOOD eiQCURVISL90SS eiQCURVISL90BL
CONTENTS SAFETY PRECAUTIONS 2 INTRODUCTION 4 DIMENSIONS 4 UNPACKING YOUR APPLIANCE 4 PRODUCT OVERVIEW – PARTS SUPPLIED 5 OPTIONS FOR VENTILATION 6 7 9 OPERATION 12 MAINTENANCE 13 TROUBLESHOOTING 15 MANUFACTURER SUPPORT 15 15 SPECIFICATION 16 1
SAFETY PRECAUTIONS Whilst this product complies with all safety requirements, incorrect or inappropriate use can lead to personal injury and potential damage to property. Please read the contents of this instruction booklet or using this cooker hood. · The cooker hood must be installed in accordance with the installation instructions provided, making sure all measurements and guidance are followed. · All installation work must be carried out or a competent person.
· If the supply cord is damaged , it must be replaced by the in manufacturer, its service agent, or order to avoid an accident. · cooker hood should not be used by people (including children) with reduced physical , sensory , or mental capabilities, or by those who lack experience and knowledge , unless they have been given supervision and instruction on how to use the appliance by a person responsible for their safety. · Accessible parts may become hot when used with cooking appliances.
INTRODUCTION Thank you for choosing an electriQ cooker hood. This instruction manual is designed to provide you with all required instructions related to the installation, use and maintenance of the appliance. In order to operate the unit correctly and safely, please read this instruction manual carefully before installation and usage.
PRODUCT OVERVIEW Description SUPPLIED Illustration Qty.
OPTIONS This hood supports both external venting or recirculation. The type of setup should be decided before commencing installation. EXTERNAL VENTING A pipe is provided which allows the cooking odours to be extracted outside. If this is the chosen installation method consideration to the route of the vent pipe should be made. The mounting plate contains a hole allowing the vent pipe to be connected and routed through the ceiling.
Do not connect the hood to the mains supply before installing it . 1. Position the hanging plate on the ceiling and then mark the position of the screw holes with a pencil. Securely using the hanging plate to the ceiling, 4 (30 mm) screws. Please ensure that the bracket is in a way it would support the weight of the hood. Depending on the construction of the ceiling, alternative may be required. 6 x expansion bolts are also provided to allow to concrete. 2.
does not drop down whilst the main body of the hood to the angle bars. 5. On the top of the hood unit, where the air outlet vent is located, the 2 x air should be carefully installed, bending very slightly so the lugs at each end the holes This enables to pivot upwards when the unit is in operation, opening up the outlet fully for the air to pass through. Please note: The small spindles/lugs at each end of each holes on the housing, not the grooves above them: the 6.
FOR MINIMUM CHIMNEY LENGTH Do not connect the hood to the mains supply before installing it. 1. Position the hanging plate on the ceiling and then mark the position of the screw holes with a pencil. Securely the hanging plate to the ceiling, using x ST4 (30 mm) screws. Please ensure that the bracket is in a way it would support the weight of the hood. Depending on the construction of the ceiling, alternative may be required. 6 x expansion bolts are also provided to allow to concrete. 2.
Please note: The small spindles/lugs at each end of each holes on the housing, not the grooves above them. 4. Securely using 16 x M5(10mm) screws, and connect the outlet with the exhaust pipe (If venting externally) 5. Slide the inner chimney and outer chimney onto the angle bars. 7. If externally venting, connect the exhaust pipe to the hanging plate. The angle bar should then be to the hanging plate using the 8 x M5 screws.
CARBON (Available Separately） Activated carbon can be used to trap odours, and must be used if the unit is not vented externally. These are available from the same stockist the hood was purchased from under reference: eIQTMCARBONCURV CARBON In order to install the activated carbon , the aluminium grease should be removed . Press the lock and pull it downward as below: Put the activated carbon onto the end of the motor unit and turn it in clockwise direction.
ON/OFF BUTTON Press this key to turn the power on and off. FAN SPEED DOWN BUTTON While the fan is operating, press this key to decrease the power one level. POWER UP BUTTON While the fan is operating press this key to increase the power one level. LIGHT BUTTON Press once to turn the lights on, press again to turn the lights off. NOTE: The display will light at half power when the hood is turned on, and the buttons will illuminate fully when they are touched.
MAINTENANCE Before cleaning, switch the unit off and pull out the plug, or switch off at the relevant mains switch. If the unit has been hard-wired in. Make sure the unit has no power being fed to it. REGULAR CLEANING Use a soft cloth moistened with hand-warm mildly soapy water or household cleaning detergent. Never use metal pads, chemicals, abrasive material or a stiff brush to clean the unit.
LIGHT BULB REPLACEMENT ker hood is supplied with 4 long life LED light , Although these are designed to have a very long lifespan ,should one fail, replacements are available from the supplier of the hood and the guide below can be followed to replace it. 1. Switch the unit off and ensure it is disconnected from the mains supply. 2. Remove aluminium grease , to prevent them from falling. 3.
TROUBLESHOOTING Fault Cause Solution The fan blade is Light on, but jammed. fan does not The motor is work damaged. Both light and fan do not work Excessive Vibration Switch off the unit. Repair to be carried out by service personnel only. Halogen light bulb blown Replace the bulb with correct rating. Power cord loose Plug in to the power supply again. The fan blade is damaged. Switch off the unit. Repair to be carried out by service personnel only. Switch off the unit.
The following shows how to reduce total environmental impact (e.g. energy use) of the cooking process). (1) Install the cooker hood in a proper place where there is ventilation. (2) Clean the cooker hood regularly so as not to block the airway. (3) Remember to switch off the cooker hood light after cooking. (4) Remember to switch off the cooker hood after cooking. FOR DISMANTLING Do not dismantle the appliance in a way which is not shown in the user manual. The appliance could not be dismantled by user.
