USER MANUAL COOKER HOOD 90CM LED ISLAND COOKER HOOD eiqislandled Thank you for choosing electriQ Please read this user manual before using this product and keep it safe for future reference. Visit our page www.electriQ.co.
CONTENTS SAFETY 3 VENT FLAP INSTALLATION 5 VENTILATION AND INSTALLATION 6 OPERATION 10 TROUBLESHOOTING 11 CLEANING AND MAINTENANCE 11 FILTER INFORMATION 12 BULB INFORMATION 13 SUPPORT 14 PRODUCT FICHE 15 2
SAFETY PRECAUTIONS Whilst this product is compliant with all safety requirements, incorrect or inappropriate use can lead to both personal injury and potential damage to property. Please read the contents of this instruction booklet thoroughly before fitting or using this appliance. • The cooker hood must be installed in accordance with the installation instructions and all measurements followed. • All installation work must be carried out by a competent person or qualified electrician.
• The minimum distance between the surface of the hob and the lowest part of the hood should be at least 65cm. A distance of between 65cm and 75cm gives peak efficiency. • The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels. • When the hood is vented externally and used with appliances which burn fuel (e.g. gas, oil, wood) the area must be sufficiently ventilated to ensure safe operation.
INSTALLATION (VENT OUTSIDE) MOUNTING OF THE V-FLAP If the cooker hood does not have an assembled V-flap 1, you should mount the halfparts to its body.The images only show an example of how to mount the V-flap,the outlet may be various according to different models and configuration. To mount the V-flap 1 you should: 1. 2. 3. 4.
OPTIONS FOR VENTILATION This hood can be set up for either external venting or recirculation of the air. The type of setup should be decided before commencing installation. EXTERNAL VENTING If you have an outlet to the outside, your cooker hood can be connected as shown in the diagram using any suitable extraction duct (enamel, aluminium, flexible pipe or inflammable material with an interior diameter of 150mm) can be used.
3. The ceiling must can bear at least 120kgs weight, and the thickness of the ceiling must be ≧ 30MM, drill 1*170mm round hole in the ceiling. 4.
7. Fix the v-flaps and converter onto the outlet. 8. Hold up the hood, 16pcs M4*10 big flat screws will be used to connect the hood body into angle iron. 9. Put the expansion pipe on the converter; after ensure all the things ok, put down the hook, take from the outside chimney, all the installation is finished. Note: the expansion pipe is not included in the product.
HINTS FOR EXHAUST DUCT INSTALLATION The following rules must be strictly followed to obtain optimal air extraction: • • • • • • • • • Keep expansion pipe short and straight. Do not reduce the size or restrict expansion pipe. When using expansion pipe always install the pipe pulled taut to minimize pressure loss. Failure to observe these basic instructions will reduce the performance and increase noise levels of the cooker hood.
START USING YOUR COOKER HOOD 1. Press the “Power” button to turn the cooker hood “on” & “off ”. 2. Press the “Speed” button to change between fan speeds. The LED will indicate the current fan speed. 1 being the slowest, and 3 being the fastest. 3. Press the “Light” button to turn the hoods light “on” or “off”. The power button does not control the light. 4. When the hood is on, press the “Timer” button and the countdown timer will begin, starting at 9 minutes.
TROUBLESHOOTING Fault Light on, but motor does not work Light does not work, motor does not work Oil leakage Lights not working Insufficient suction The Cooker hood inclines Possible Cause Solution Fan switch turned off Select a fan switch position. Fan switch failed Contact service center. Motor failed Contact service center. House fuses blown Reset/Replace fuses. Power cord loose or disconnected Refit cord to power outlet. Switch power outlet on.
CLEANING THE FILTERS • Remove the filters by pulling the latch until the filter cover comes off. • Put into a dishwasher with detergent, set the temperature below 60 degrees. Or wash by hand with warm soapy water, making sure to dry thoroughly. • Make sure that the hood is disconnected from the mains before cleaning or maintenance.
BULB REPLACEMENT Before changing the bulb, ensure the hood is turned off and the power is disconnected before attempting to change the bulb. Wait until the flitting has cooled down before commencing replacement. • Open the LED light plate assembly and take away the grease filter.See pic 1. • Find the light wire at the back of the wire outlet.Then slightly pull the light connecting wire out, and dismantle the terminal of the light connecting wire. See pic 2.
INFORMATION FOR DISMANTLING Do not dismantle the appliance in any way which is not shown in the user manual. The appliance must not be dismantled by an unqualified person. At the end of its life, the appliance should not be disposed of with general household waste. Check with your Local Authority or retainer for recycling advice. electriQ UK SUPPORT www.electriQ.co.uk/support Call: 0330 390 3061 Office hours: 9AM - 5PM Monday to Friday www.electriQ.co.
PRODUCT FICHE 15
