USER MANUAL COOKER HOOD eiQSLIM100TOUCH Thank you for choosing electriQ. Please read this user manual before using this Cooker Hood and keep it safe for future reference. Visit our page www.electriQ.co.
CONTENTS Safety Precautions 2 Introduction 4 Unpacking your appliance 4 Product Overview – Parts Supplied 5 Options for Ventilation 6 Installation 7 Operation 9 Maintenance Cleaning your hood 10 Grease filters – cleaning/replacing 10 Carbon Filters (optional) – use and replacement 11 Bulb replacement 12 Troubleshooting 13 Manufacturer Support 13 Technical Specification 14 1
SAFETY PRECAUTIONS Whilst this product is compliant with all safety requirements, incorrect or inappropriate use can lead to both personal injury and potential damage to property. Please read the contents of this instruction booklet thoroughly before fitting or using this appliance. • The cooker hood must be installed in accordance with the installation instructions and all measurements followed. • All installation work must be carried out by a competent person or qualified electrician.
• The minimum distance between the surface of the hob and the lowest part of the hood should be at least 65cm. A distance of between 65cm and 75cm gives peak efficiency. • The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels. • When the hood is vented externally and used with appliances which burn fuel (e.g. gas, oil, wood) the area must be sufficiently ventilated to ensure safe operation.
INTRODUCTION Thank you for choosing your electriQ cooker hood. This instruction manual is designed to provide you with all the required instructions related to the installation, use and maintenance of the appliance. In order to operate the unit correctly and safely, please read this instruction manual carefully before installation and usage.
PRODUCT OVERVIEW - PARTS SUPPLIED Description Cooker hood Illustration Qty.
OPTIONS FOR VENTILATION This hood can be set up for either external venting or recirculation of the air. The type of setup should be decided before commencing installation. EXTERNAL VENTING If you have an outlet to the outside, your cooker hood can be connected as shown in the diagram using the flexible exhaust pipe (supplied). Alternatively, any suitable extraction duct (enamel, aluminium, flexible pipe or inflammable material with an interior diameter of 150mm) can be used.
INSTALLATION . 1. Before installation, ensure you have not connected the appliance to the mains supply. 2. The cooker hood should be placed at a distance of 65~75cm above the cooking plane for best effect. 3. Use the supplied screws (4mm x 40mm) and wall plugs to attach the mounting bracket to the wall in the correct position to set the hood height, ensuring the bracket is kept level.
5. The 2 air flaps should now be installed, as access is easier before the unit is wall mounted. The 2 flaps should be carefully installed to the top of the hood unit, bending them slightly so the lugs at each end locate into the holes in the outlet vent. When the unit is in operation the flaps pivot upwards to allow airflow. Please note: the small spindles/lugs at each end of each flap locate into the holes on the housing, not the grooves above them.
8. Slide the inner chimney upwards and connect it to Plate 2 using the two remaining 4mm x 8mm screws. Before using the hood, read all the instructions and make sure that the voltage (V) and the frequency (Hz) indicated on the identification plate (found inside the cooker hood) and all the data inside the appliance are exactly the same as the voltage and frequency in your home.
MAINTENANCE Before cleaning the hood, it should be switched off and power removed, by removing the plug or if the unit has been hardwired, switching off at the pole switch, to ensure no power is been fed to the unit. Regular Cleaning Use a soft cloth moistened with hand-warm mildly soapy water or household cleaning detergent. Never use metal pads, chemicals, abrasive material or a stiff brush to clean the unit, as these could scratch or damage the surface.
CARBON FILTER（OPTIONAL） Activated carbon filters are used to trap odours and must be used if the hood is not vented to the outside. They are available from the same retailer the hood was purchased from under reference: eiQCF110 1. Before installing or replacing the carbon filters, please remove power to the unit. 2. The carbon filters attach to the sides of the motor housing. This can be accessed by removal of the metal grease filters on the base of the hood 3.
BULB REPLACEMENT IMPORTANT: The light fitting must be replaced by the manufacturer, its service agent or similarly qualified persons. This hood is fitted with LED light units, which under normal operation can last the lifetime of the hood. In the event that one does fail, replacement light units are available from the same retailer the hood was purchased from.
TROUBLESHOOTING Fault Light on, but fan does not work Both light and fan do not work Cause The fan blade is jammed. The motor is damaged. Light bulb blown Power cord loose The fan blade is damaged. Excessive Vibration Suction performance not good The fan motor is not fixed tightly. The unit is not hung properly on the bracket. Air flaps have detached and fallen into motor housing 1 Grease filters clogged? 2 Distance between the unit and the cooking plane too great. Solution Switch off the unit.
TECHNICAL SPECIFICATION Symbol Value Model identification Annual Energy Consumption Unit eiQSLIM100TOUCH AEChood 59.0 f 1,1 FDEhood 24.1 EEIhood 62.6 QBEP 348.6 m3/h Measured air pressure at best efficiency point PBEP 347 Pa Maximum airflow Qmax 605.1 m3/h W BEP 139.7 W WL 4,0 W Emiddle 127 lux PS - W PO 0.
INFORMATION FOR DISMANTLING Do not dismantle the appliance in any way which is not shown in the user manual. The appliance must not be dismantled by an unqualified person. At the end of its life, the appliance should not be disposed of with general household waste. Check with your Local Authority or retainer for recycling advice. electriQ UK SUPPORT www.electriQ.co.uk/support Call: 03303903061 Office hours: 9AM - 5PM Monday to Friday www.electriQ.co.
