INSTALLATION AND USER MANUAL COOKER HOOD eiQTMVISORSTEEL eiQTMVISORWH Please read this manual before using or installing the cooker hood and keep it safe for future reference. Visit our page www.electriQ.co.
CONTENTS IMPORTANT SAFETY INFORMATION 3 PARTS 5 INSTALLATION 6 CHANGING THE VENTILATION METHOD 6 CHANGING THE VENTILATION OUTLET 7 PREPARING FOR INSTALLATION 8 CUPBOARD MOUNTING INSTALLATION 9 WALL MOUNTING INSTALLATION 10 OPERATION 11 REPLACING THE BULB 12 INSTALLING THE OPTIONAL CARBON FILTER 12 CLEANING AND MAINTENANCE 13 TROUBLESHOOTING 14 SPECIFICATION 15 MANUFACTURER SUPPORT 16 2
IMPORTANT SAFETY INFORMATION Please read this instruction manual carefully and retain for future reference. It contains important information concerning the safe operation, installation and maintenance of the appliance. There must be adequate ventilation of the room when the hood is used at the same time as appliances burning gas or other fuels. This cooker hood is only designed for domestic use, and should not be used in a commercial environment.
Children must not play with the appliance. Cleaning and user maintenance must not be carried out by children without supervision. When the hood is being maintained, cleaned or filters changed, make sure it is switched off at the mains supply. The exterior of the hood should be cleaned with mild detergent on a warm damp sponge or cloth. The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels.
PARTS Description Illustration Qty Cooker hood 1 Outlet assembly 1 Outlet cover 1 Rear Air Flow Adaptor 1 Screw (4mm x 30mm) 6 Wall plug 6 DIMENSIONS 5
INSTALLATION BEFORE INSTALLING YOUR CANOPY HOOD: Please read the instructions carefully. Unpack the hood and check that all functions are working. Ensure that the voltage (V) and the frequency (Hz) indicated on the serial plate match the voltage and frequency at the installation site. Check that the area behind the installation surface to be drilled is clear of any electrical cables or pipes, etc. The surfaces of the canopy are very easily damaged during installation if grazed or knocked by tools.
INFORMATION Sufficient air is needed for proper combustion and exhaustion of gases through the flue (chimney) of fuel burning equipment to prevent back drafting. Ductless fans must always be vented to the outdoors. When assessing the air pressure, the entire ventilation system in the house/apartment must be taken into account. All legal regulations must be observed for the conveyance of exhaust air.
PREPARING FOR INSTALLATION: Ensure the power has been turned off at the mains before beginning installation. Connection to the mains supply must be in an accessible location. To install this hood you will require two assistants.
CUPBOARD MOUNTING INSTALLATION: 1. Drill a 130mm diameter and four 6mm diameter holes as shown in the diagram. NOTE: If your cooker hood is to be used in recirculating air mode or is configured for rear venting, it is not necessary to cut the 130mm diameter hole. 2. Attach the one way valve and then use 4 screws to fix the cooker hood to the underside of the kitchen cupboard. Check that your fixings are correctly located, by temporarily fitting the cooker hood. If correct, fit the unit into position.
WALL MOUNTING INSTALLATION: 1. 2. 3. 4. 5. 6. Drill two 8mm diameter holes in the correct position on the wall when compared to the hanging holes on the rear of the hood. Make sure the hood is aligned directly over the hob, a minimum of 65cm above the hob surface. Insert two plastics wall plugs into the holes. Insert two screws into the wall plugs and tighten them leaving around 3mm protruding from the wall. Mount the cooker hood onto the two screws and mark the bottom two screw positions.
OPERATION MOTOR OFF BUTTON: Press on this switch to stop operation of the motor. LOW SPEED BUTTON: Press to run the motor at LOW speed. MEDIUM SPEED BUTTON: Press to run the motor at MEDIUM speed. HIGH SPEED BUTTON: Press to run the motor at HIGH speed. LIGHT ON/OFF BUTTON: Press to turn on the lights, press again to turn them off.
REPLACING THE BULB 1. Switch off the extractor hood and ensure it is also switched off at the mains supply. 2. Remove the grease filter. 3. Unclip the lamp holder using the spring clip on the rear of the holder. 4. Disconnect the wiring connector on the lead running from the lamp holder. 5. Replace the holder and lamp with identical unit available from the retailer/manufacturer. 6. Remember to switch on at the mains once installation is completed and the hood has been fully reassembled.
CLEANING AND MAINTENANCE Disconnect range hood from power supply before cleaning or servicing. 1. Clean the hood surface frequently using mild detergent and a warm damp sponge or cloth. 2. Do not use harsh alkalis or abrasives. 3. Avoid the use of scouring powers or dishwasher compounds. 4. If the optional carbon filter is being used, these cannot be cleaned and require replacing every 2-3 months depending on frequency of use. They are available from the retailer who supplied your hood.
TROUBLESHOOTING Fault Light on, but fan does not work Both light and fan do not work Excessive Vibration Suction performance not good Cause Solution The fan blade is jammed. Switch off the unit. Repair to be carried out by qualified service personnel only. The motor is damaged. Power cord loose Plug in to the power supply again. The fan blade is damaged. Switch off the unit. Repair to be carried out by qualified service personnel only. The fan motor is not fixed tightly. Switch off the unit.
SPECIFICATION Symbol AEChood f FDEhood EEIhood Value eiQTMVISORWH eiQTMVISORSTEEL 33.55 1.65 9.6 73.52 kWh/a QBEP 95.86 m3/h PBEP Qmax 191.91 201.55 Pa m3/h WBEP 53.
MANUFACTURER SUPPORT www.electriQ.co.uk Unit J6, Lowfields Business Park Lowfields Way, Elland West Yorkshire, HX5 9DA Telephone: 0871 984 4416 Office Hours: 9:00am to 5:00pm Monday to Friday ENVIRONMENTAL PROTECTION Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. INFORMATION FOR DISMANTLING Do not dismantle the appliance in a way which is not shown in the user manual.
