USER MANUAL OUTDOOR MULTI POSITION ELECTRIC HEATER WITH REMOTE AND LIGHT EQODETVH Thank you for choosing electriQ Please read the manual before using this heater and keep it safe for future reference. Visit our page www.electriQ.co.
CONTENTS SAFETY INSTRUCTIONS 3 PRODUCT OVERVIEW 5 ASSEMBLY 6 OPERATION 9 CONTROL PANEL 9 CHANGING THE ORIENTATION 10 CLEANING AND MAINTENANCE 11 TECHNICAL SPECIFICATIONS 11 TROUBLESHOOTING 11 SUPPORT 12 2
SAFETY INSTRUCTIONS IMPORTANT • • • • • • • • • • • • • • • • • • • • • • • Carefully read the instructions before operating this unit. This appliance is for outdoor use only. Rating: This unit must be only connected to a 220-240 V / 50 Hz earthed outlet. Installation must be in accordance with the regulations of the country where the unit is used. If you are in any doubt about the suitability of your electrical supply have it checked and, if necessary, modified by a qualified electrician.
• • • • • • • • • • • • • • • • • • • • user-serviceable parts. Always unplug or disconnect the appliance from the mains power supply when not in use, or when moving or cleaning it. Do not pull the cord to unplug the heater. Keep the heater clean. Do not allow any object to enter the ventilation or exhaust opening as this may cause electric shock, fire, or damage to the heater. Do not use the appliance for anything other than its intended use.
PRODUCT OVERVIEW PARTS PART NO. PART NAME QTY 1 Heater Body 2 3 4 5 Panel Upright Sections Base cover Base 1 2 2 1 1 FITTINGS PART NO. DIAGRAM QTY 6 M4×10 Bolt 6 7 Washer 2 8 9 5 PART NAME ST3.
ASSEMBLY STEP 1: Using four BOLTS (6), attach the 2 CASTORS (11) to one side of the base. On the other side of the base attach the FEET (13), ensuring that the FOOT COLLARS (12) are in place. STEP 2: Place the base gently onto its feet before attaching the two UPRIGHT SECTIONS (3) using four WASHERS (14) and four BOLTS (9).
STEP 3: Gently place the BASE COVER (4) over the two upright sections and guide it down until it fits securely onto the base. STEP 4: Place the main body of the heater onto the support brackets and fix in position using two M4X10 BOLTS (6). Then slide the power cable through the hole in the base.
STEP 5: Slide the BASE COVER (4) up to the base of the main body, gently push both PANELS (2) into position until they are securely in place. Do not complete this step until you have successfully pulled the power cable through the base. When complete, slide the BASE COVER back down so it is back in its original place. STEP 6: Secure the base into place using two WASHERS (7) and two ST3.5×12 Screws (8). IMPORTANT! Remove all protection pieces from the heating tube before switching the heater on.
OPERATION Plug in the power cable, the heater will bleep. The heater is in “Stand By” mode, the POWER indicator will be illuminated blue. TO TURN ON TO SELECT THE HEAT LEVEL TO SELECT THE LED BRIGHTNESS Press the POWER button and the indicator will turn white, indicating the heater is on. The heat will default to level 3. Repeatedly press the HEAT button to select the heat output. There are 5 levels between 1 (Low) and 5 (High).
CHANGING THE HEATERS ORIENTATION The heater can be set up with the heating tube in either a vertical or horizontal position. To change to horizontal position, push the base on the main body out of the frame so it pivots at the top, until the main body is horizontal. Lock the main body into position by securing the clip on the main body to the top of the upright. TO CHANGE BACK TO VERTICAL: Reverse the steps above, ensuring the body is adequately supported and slowly lowered back to the upright position.
CLEANING AND MAINTENANCE ATTENTION: Please turn off the unit and unplug from the mains and allow to fully cool before cleaning or performing any maintenance. CLEANING THE SURFACE • Clean the heater with a duster or a soft wet cloth. • Do not use chemical solvents (such as benzene, alcohol or gasoline) as they may cause irreversible damage. Make sure no water enters the control panel or gaps in the casing. • Do not run the unit until completely dry.
electriQ UK SUPPORT www.electriQ.co.uk/support Please, for your own convenience, make these simple checks before calling the service line. If the unit still fails to operate call: 0330 390 3061 or complete the online form 1. Is the unit plugged into the mains? 2. Is the fuse OK? 3. Switch the unit off and wait three minutes to see if the issue is resolved. Restart the unit. Office hours: 9AM - 5PM Monday to Friday www.electriQ.co.
