USER MANUAL Window Cleaning Robot iQlean-WR01 Thank you for choosing your electriQ robot window cleaner. This instruction manual is designed to provide you with all required instructions related to the installation, use and maintenance of the appliance. In order to operate the unit correctly and safely, please read this instruction manual carefully before installation and usage.
CONTENTS SAFETY 3 PRODUCT OVERVIEW 5 ASSEMBLY 6 OPERATION 7 DIAGNOSTICS 9 CLEANING AND MAINTENANCE 9 TROUBLESHOOTING 9 TECHNICAL SPECIFICATION 11 SUPPORT 11 2
SAFETY PRECAUTIONS Important • Carefully read the instructions before operating the unit. Please retain the manual for future reference • Before use ensure product’s safety harness is securely fastened. • People on the ground and balconies below the robot should be protected from the danger of injury caused by accidental failure of the robot. • This robot window cleaner has been tested and is safe to use. However, as with any electrical appliances - use it with care.
• Do not use the appliance for any other purposes than its intended use. • Do not use the appliance in places with high humidity (>80%RH) • Do not immerse the robot in water or other liquids. If the robot is immersed in water or other liquids by mistake, do not touch it with your hands. If the appliance is immersed in water or other liquids, discard it. • Do not use in an environment where there is a risk of fire or explosion.
PRODUCT OVERVIEW Your robot window cleaner is designed to clean windows at a rate of 4 minutes per square meter. It is mains powered and has a backup battery to power the unit in the event of a power cut. A remote control can be used to set the robot on a cleaning pattern or it can be controlled manually. It can detect the edge of windows and change direction. The device is protected by a safety harness, in the unlikely event of a loss of suction.
ASSEMBLY CLEANING CLOTH Cleaning ring Cleaning cloth The robot has two cleaning wheels on its underside. Each wheel requires a cleaning cloth, which is in turn held in place by a cleaning ring. Take the cleaning ring, and warp the cleaning cloth over it. Take the assembled ring and cloth and press it onto the cleaning wheel. CONNECTING THE POWER SUPPLY The robot window cleaner requires connection to the power supply at all times of operation. Referring to the diagram below/following page, 1.
Mains Power Supply ‘figure of 8’ jack Extension cable (4m) Safety harness Once the power is switched on, check the fan is creating suction and that the status indicator lights are OK. Place the robot on the window, keep it away from the window frame initially. Check that the suction can hold the device, then let go. To remove the device, use one hand to gently pull the safety harness, and use your other hand to remove the robot.
STEP2：DAMP CLEAN Remove the dirty cleaning cloths and replace with clean ones. Spray the clean cloths with 1 to 2 spays of cleaning agent so that the cloth is damp but not wet. A wet cleaning cloth will give poor results. REMOTE CONTROL The robot’s movements are controlled either manually or can be set to follow predetermined patters. The robot window cleaner can receive signals from the front and the back side of the machine so it can be controlled from either side of the glass.
DIAGNOSTICS The functional status of the robot can be read from its status indicator window. There are three LEDs, one in the left of the window, one in the centre and one on the right.
• • • • Cleaning cloth is too wet Glass is already very clean and slippery Humidity is too low Solution: use program , , or putting the machine in the middle of the window to avoid malfunction 5. Uneven operation of the machine • Cleaning cloth is too dirty. Replace cloth with clean one. • Uneven areas on the surface of the glass, for example algae. • Cleaning wheel loose, please tighten. 6. Due to a power outage, the machine makes warning sound and red light flashes • Robot is using backup battery.
TECHNICAL SPECIFICATION Product dimensions 298 x 150 x 120mm Product weight 945g Input Voltage 100-240VAC,50Hz/60Hz Power supply output 24V, 3.75A Adapter certification CE, UL, FCC Power consumption 80W AC power cord length 1.0m DC power cord length 4.0m Safety harness length 4.5m Battery 4 x Li-Po, 3.
