User Manual

ManualsBrandsElectro Harmonix ManualsGuitar EffectsHOG2 Foot Controller - FOOT PEDAL FOR HOG2

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may

cause undesired operation. If the device is not installed and used in accordance with

the instructions, it may cause harmful interference to radio communications and void

the user's authority to guarantee the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Modifications not expressly approved by the manufacturer could void the user's

authority to operate the equipment under FCC rules.

H.O.G.2 FOOT CONTROLLER

Preset Controller for HOG2

Congratulations on your purchase of the Electro Harmonix HOG2 FOOT

CONTROLLER! When connected to your HOG2 main unit, the Foot Controller gives

you access to 100 presets, allowing you to load and save your favorite HOG2

settings. Every slider position and mode selection is stored when you save a preset

and faithfully recalled when you load the preset at a later date. If an expression pedal

is connected to the HOG2 it will even store its position at the time of saving.

- GETTING STARTED -

Connect the HOG2 Foot Controller (HOG2 FC) to your HOG2 main unit using a

standard 1/4” mono instrument cable. Plug into the jack labeled FOOT CONTROLLER

on the HOG2. The other end of the cable should be inserted into the HOG2 FC’s jack

labeled INPUT. As long as the HOG2 main unit is powered up, the digits on the HOG2

FC will light up indicating it is ready for use.

- DISPLAY AND CONTROLS -

2-DIGIT LED DISPLAY – The LEDs display the currently selected or loaded preset

number. The numbers range from 0 to 99. When a preset is loaded, the rightmost

decimal point on the HOG2 FC and PRESET LED on the HOG2 main unit will light

indicating a PRESET is active. If the rightmost decimal point is not lit, then either no

PRESET is currently loaded or the HOG2 is in bypass mode.

UP/DOWN Footswitches – If no preset is currently loaded, pressing either

footswitch will load the preset associated with the currently displayed number. For

example, if the HOG2 FC is displaying 0 and the decimal point next to 0 is not lit,

pressing either footswitch will load Preset 0.

If a preset is loaded, press and release the UP Footswitch and the digits on the HOG2

FC will increment by one while simultaneously loading the preset indicated by the

new number. For example, if your HOG2 FC is displaying 0 and you press the UP

Footswitch, the display will load and show Preset 1. The DOWN footswitch does the

same but instead decrements by one.

Press and hold either footswitch for approximately half a second to jump up or down

by ten presets instead of just one.

SELECT Knob – The SELECT knob can be used to scroll through the presets without

loading a new preset. Turn the knob clockwise to scroll up through the presets, turn

the knob counter-clockwise to scroll down. Press and release the SELECT knob to

load the currently displayed preset. If a preset is loaded, and you turn the SELECT

knob, the numbers will blink indicating that a different preset is actually loaded.

Summary of content (2 pages)

PAGE 1
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. If the device is not installed and used in accordance with the instructions, it may cause harmful interference to radio communications and void the user's authority to guarantee the equipment.
PAGE 2
Press and hold the SELECT knob for approximately 3 seconds to save the current HOG2 setting to the preset number currently displayed. After holding the SELECT knob for 3 seconds, the numbers will disappear for 1 second, indicating that the preset has been saved. - SAVING AND LOADING SAVING A PRESET To save your current HOG2 setting, turn the SELECT knob until the HOG2 FC displays the preset number you would like to save to. Now press and hold the SELECT knob for 3 seconds.