Datasheet

ManualsBrandsElectro Industries ManualsBoilerEB-MA-10

Datasheet

Illuminated 30 mm mount electro-mechanical push buttons

• Rugged design; easy installation with no assembly or individual wiring required

• Push-to-stop, twist-to-release, or pull-to-release operation per IEC60947-5-5

• Latching design complies with ISO 13850; direct (positive) opening operation

per IEC 60947-5-1

• Compliant with ANSI B11.19, ANSI NFPA79, and IEC/EN 60204-1 Emergency

Stop requirements

• “Safe Break Action” ensures N.C. contacts will open if the contact block is

separated from the actuator

• 8-pin M12/Euro-style Quick Disconnect

• Models with YELLOW and RED indication of actuation (armed or depressed/

latched button)

• "Emergency Stop" legend included

• U.S. Patent No. Des. 700,149

Models SSA-EB… series are "mushroom-style" electro-mechanical emergency stop push buttons. When the button is

armed, the switch's safety contacts (N.C.) are closed and its monitoring contacts (N.O.), if present, are open. When the

button is pushed, the switch's safety contacts open and the monitoring contacts close. The contacts remain in this

condition until the push button is manually rearmed by pulling or twisting clockwise the red push button actuator.

The SSA-EB1(2)P..-..ECQ.. series has a 30 mm mounting base similar to Banner’s OTB, VTB, and STB Optical Touch

Buttons for ease of mounting without requiring an additional enclosure. The EZ-LIGHT

illumination logic allows for easy

identification of a pushed/actuated button. An armed button is either a steady yellow illumination or OFF, a pushed/

actuated button is indicated by a red flashing illumination. An optional input allows an armed button to illuminate a steady

red to indicate a machine stop or emergency stop condition.

Models

Model

Push Button EZ-LIGHT

Illumination Logic Connection

SSA-EB1PL-12ECQ8

Standard 40 mm

OFF (armed), RED (solid, PUSH)

8-pin M12 QD

SSA-EB1PLXR-12ECQ8 OFF (armed), RED (flash, PUSH)

SSA-EB1PLYR-12ECQ8 YELLOW (armed), RED (flash, PUSH)

SSA-EB1PLGR-12ECQ8 GREEN (armed), RED (flash, PUSH)

SSA-EB2PLXR-12ECQ8 Large 60 mm OFF (armed), RED (solid, PUSH)

Important... Read this before proceeding!

The user is responsible for satisfying all local, state, and national laws, rules, codes, and regulations relating to

the use of this product and its application. Banner Engineering Corp. has made every effort to provide complete

application, installation, operation, and maintenance instructions. Please contact a Banner Applications Engineer with any

questions regarding this product.

The user is responsible for making sure that all machine operators, maintenance personnel, electricians, and

supervisors are thoroughly familiar with and understand all instructions regarding the installation, maintenance, and use of

this product, and with the machinery it controls. The user and any personnel involved with the installation and use of this

product must be thoroughly familiar with all applicable standards, some of which are listed within the specifications.

Banner Engineering Corp. makes no claim regarding a specific recommendation of any organization, the accuracy or

effectiveness of any information provided, or the appropriateness of the provided information for a specific application.

SSA-EB Series Lighted Emergency Stop

Push Buttons

Original Document

162754 Rev. D

24 November 2014

162754

Summary of content (10 pages)

PAGE 1
SSA-EB Series Lighted Emergency Stop Push Buttons Datasheet Illuminated 30 mm mount electro-mechanical push buttons • • • • • • • • • Rugged design; easy installation with no assembly or individual wiring required Push-to-stop, twist-to-release, or pull-to-release operation per IEC60947-5-5 Latching design complies with ISO 13850; direct (positive) opening operation per IEC 60947-5-1 Compliant with ANSI B11.19, ANSI NFPA79, and IEC/EN 60204-1 Emergency Stop requirements “Safe Break Action” ensures N.C.
PAGE 2
SSA-EB Series Lighted Emergency Stop Push Buttons WARNING: Not a Safeguarding Device An Emergency Stop Device is not considered a safeguarding device because it requires an overt action by an individual to stop machine motion or hazards. A safeguarding device limits or eliminates an individual's exposure to a hazard without action by the individual or others.
PAGE 3
SSA-EB Series Lighted Emergency Stop Push Buttons WARNING: Shock Hazard and Hazardous Energy Always disconnect power from the safety system (for example, device, module, interfacing, etc.) and the machine being controlled before making any connections or replacing any component.
PAGE 4
SSA-EB Series Lighted Emergency Stop Push Buttons Situation Indication Illumination Logic RED / SOLID Button Armed • • Pin 3 = +Vdc Indicates the machine is in an Emergency Stop or other stop condition, but that specific button has not been pushed (actuated) This optional signal (12 to 30Vdc) allows the user to indicate a stop condition by turning the armed indication to RED (steady) indication Table 4: SSA‐EB1xxL‐xx See Figure 1 on page 4.
PAGE 5
SSA-EB Series Lighted Emergency Stop Push Buttons Checkout At machine set up, a Designated Person2 should test each emergency stop push button for proper machine shutdown response. A Designated Person should check the emergency stop buttons for proper operation, physical damage, button looseness, and excessive environmental contamination. This should take place on a periodic schedule determined by the user, based on the severity of the operating environment and the frequency of switch actuations.
PAGE 6
SSA-EB Series Lighted Emergency Stop Push Buttons Rated Operating Current and Voltage (Ue) Safety Contact (N.C.) 30 V 60 V ac/75 V dc Resistive Load (AC-12) - 2A Inductive Load (AC-15) - 2A Resistive Load (DC-12) 2A 0.4 A Inductive Load (DC-13) 1A 0.22 A 30 V 60 V ac/75 V dc AC 50/60 Hz DC Auxiliary Output (N.O.) Resistive Load (DC-12) 0.25 A n.a. Inductive Load (DC-13) 0.25 A n.a.
PAGE 7
SSA-EB Series Lighted Emergency Stop Push Buttons Accessories Mounting Brackets 60 85 SSA-MBK-EEC1 • Single 30 mm hole • 8 gauge steel, black finish (zinc-plated) • Front surface for customer applied labels 80 45 B A 60 170 SSA-MBK-EEC2 • Two 30 mm holes • 8 gauge steel, black finish (zinc-plated) • Front surface for customer applied labels 45 B 80 A 60 255 SSA-MBK-EEC3 • Three 30 mm holes • 8 gauge steel, black finish (zinc-plated) • Front surface for customer applied labels 45 B 80 A The
PAGE 8
SSA-EB Series Lighted Emergency Stop Push Buttons 8-Pin Threaded M12/Euro-Style Cordsets―Double Ended Model (8-pin/8-pin )4 Length DEE2R-81D 0.31 m (1 ft) DEE2R-83D 0.91 m (3 ft) DEE2R-88D 2.44 m (8 ft) DEE2R-815D 4.57 m (15 ft) DEE2R-825D 7.62 m (25 ft) DEE2R-850D 15.2 m (50 ft) Style Pinout Female 2 8 M12 x 1 ø 14.5 5 Male 44 Typ. 1 22.9 m (75 ft) 7 6 2 3 4 M12 x 1 ø 14.5 DEE2R-8100D 3 4 1 7 6 40 Typ.
PAGE 9
SSA-EB Series Lighted Emergency Stop Push Buttons Model Length CSS-M12F81M12M81M12F81 1 ft CSS-M12F83M12M81M12F81 3 ft CSS-M12F88M12M81M12F81 8 ft SSA-EB1PLxR-12ECQ8 E-Stop # 2 3 1 5 8 6 4 2 8-Pin M12 Female DEE2R-8xxD 8-pin M12 QD splitter cordset for use with SSAEB1PLxR-12ECQ8 SSA-EB1PLxR-12ECQ8 E-Stop # 1 EZ-LIGHT Logic B A 0V C Description C 3 1 7 EZ-LIGHT Logic B A 0V 5 8 6 4 2 7 8-Pin M12 Female TRUNK CSS-M12F81M12M81M12F81 CSS-M12F83M12M81M12F81 CSS-M12F88M12M81M12F81 8-Pin M1
PAGE 10
SSA-EB Series Lighted Emergency Stop Push Buttons ISO 13850 (EN 418) Emergency Stop Devices, Functional Aspects – Principles for Design IEC 62061 Functional Safety of Safety-Related Electrical, Electronic and Programmable Control Systems ISO 13849-1 (EN 954-1) Safety-Related Parts of Control Systems IEC 60204-1 Electrical Equipment of Machines Part 1: General Requirements IEC 60947-1 Low Voltage Switchgear – General Rules IEC 60947-5-1 Low Voltage Switchgear – Electromechanical Control Circuit Devices IEC