Specifications

ManualsBrandsElectro Industries ManualsBoilerEB-MA-10

30 mm Panel Mount Electro-Mechanical Push Buttons

Features

• Four styles of actuators: standard, illuminated, lockable, and illuminated lockable

• Push-to-stop, twist-to-release (standard and lockable), or pull-to-release (stand-

ard) operation per IEC60947-5-5

• Latching design complies with ISO 13850; direct (positive) opening operation per

IEC 60947-5-1

• Compliant with ANSI B11.19, ANSI NFPA79, and IEC/EN 60204-1 Emergency

Stop requirements

• “Safe Break Action” ensures N.C. contacts will open if the contact block is sepa-

rated from the actuator

• Panel mount though 30 mm mounting hole

• "Emergency Stop" legend optional

Models SSA-EB… series are "mushroom-style" electro-mechanical emergency stop push buttons. These buttons mount through a 30 mm

hole in an enclosure. When the button is armed, the switch's safety contacts (N.C.) are closed and its monitoring contacts (N.O.), if

present, are open. When the button is pushed, the switch's safety contacts open and the monitoring contacts close. The contacts remain

in this condition until they are manual rearmed. The standard 40 mm and 60 mm actuators can be rearmed by pulling or twisting clock-

wise the red actuator. The lockable 44 mm actuator can be rearmed only by twisting the actuator clockwise. Do not pull the actuator while

twisting or the switch may be damaged, causing a malfunction or operational failure. The illuminated models provide a RED indication

within the face of the button that allows for easy identification of a pushed/actuated button.

SSA-EB1M… series padlock-style lockable emergency stop push buttons are intended to prevent unauthorized or accidental resetting of

a pushed/latched button. The SSA-EB1M… series are not to be used as an energy isolating device or as the sole means of complying

with Lockout/Tagout or with the requirements of the isolation of hazardous energy (see OSHA 29CFR1910.147, ANSI Z244.1, CSA Z460,

ISO 14118). The locking feature can be used to provide supervisory/personal control and provide an additional safety measure(s) to

reduce the likelihood of inadvertent arming and energization of the emergency stop circuit.

Models

Non-Illuminated Models

Standard 40 mm Standard 60 mm Lockable 44 mm E-Stop Contact

SSA-EB1P-02 SSA-EB2P-02 SSA-EB1MP-02 2 N.C.

SSA-EB1P-04 SSA-EB2P-04 SSA-EB1MP-04 4 N.C.

SSA-EB1P-11 SSA-EB2P-11 SSA-EB1MP-11 1 N.C. / 1 N.O.

SSA-EB1P-13 SSA-EB2P-13 SSA-EB1MP-13 3 N.C. / 1 N.O.

SSA-EB1P-22 SSA-EB2P-22 SSA-EB1MP-22 2 N.C. / 2 N.O.

Illuminated Models

Standard 40 mm Lockable 44 mm LED E-Stop Contact

SSA-EB1PL1-02 SSA-EB1ML1P-02 Per Hookup 2 N.C.

SSA-EB1PL1-04 SSA-EB1ML1P-04 Per Hookup 4 N.C.

SSA-EB1PL1-11 SSA-EB1ML1P-11 Per Hookup 1 N.C. / 1 N.O.

SSA-EB1PL1-13 SSA-EB1ML1P-13 Per Hookup 3 N.C. / 1 N.O.

SSA-EB1PL1-22 SSA-EB1ML1P-22 Per Hookup 2 N.C. / 2 N.O.

SSA-EB1PL2-12 SSA-EB1ML2P-12 PUSH ON 2 N.C. / 1 N.O.

SSA-EB Series Emergency Stop Push Buttons

P/N 168349_web

Rev. B

4/3/2013

Summary of content (11 pages)

PAGE 1
SSA-EB Series Emergency Stop Push Buttons 30 mm Panel Mount Electro-Mechanical Push Buttons Features • Four styles of actuators: standard, illuminated, lockable, and illuminated lockable • Push-to-stop, twist-to-release (standard and lockable), or pull-to-release (standard) operation per IEC60947-5-5 • Latching design complies with ISO 13850; direct (positive) opening operation per IEC 60947-5-1 • Compliant with ANSI B11.
PAGE 2
SSA-EB Series Emergency Stop Push Buttons Important... Read this before proceeding! The user is responsible for satisfying all local, state, and national laws, rules, codes, and regulations relating to the use of this product and its application. Banner Engineering Corp. has made every effort to provide complete application, installation, operation, and maintenance instructions.
PAGE 3
SSA-EB Series Emergency Stop Push Buttons Installation and Maintenance The device must not be affected by environmental conditions. Install the device so that operation is not impeded, but should be protected against inadvertent operation (for example, accidental actuation by being bumped or leaned against). Do not operate the switch using a tool. Do not expose the switch to excessive shocks and vibrations, otherwise the switch may be deformed or damaged, causing malfunction or operation failure.
PAGE 4
SSA-EB Series Emergency Stop Push Buttons Panel Mounting 1. Remove the contact block and the M30 jam nut from the actuator and verify that the rubber gasket is in place. 2. Align the anti-rotation key on the bezel with the keyway (notch) in the panel. 3. Insert the actuator into the hole from the front of the panel, and tighten the M30 jam nut using wrench SSA-EB1-LRW or SSA-EB1LRTW to a maximum torque of 2.5 N•m (1.8 ft-lbs).
PAGE 5
SSA-EB Series Emergency Stop Push Buttons Non-Illuminated E-Stop Contact SSA-EB1P-04 SSA-EB1MP-04 4 N.C. SSA-EB1P-11 SSA-EB1MP-11 Hookup 11 12 22 41 21 42 1 N.C. / 1 N.O. 32 31 11 12 Illuminated E-Stop Contact SSA-EB1PL1-04 SSA-EB1ML1P-04 4 N.C. Hookup 11 12 22 41 21 LED24V 42 X1 32 31 X2 SSA-EB1PL1-11 SSA-EB1ML1P-11 1 N.C. / 1 N.O. 11 12 LED24V SSA-EB1P-13 SSA-EB1MP-13 3 N.C. / 1 N.O. SSA-EB1P-22 SSA-EB1MP-22 24 23 11 12 X1 24 22 41 21 42 2 N.C. / 2 N.O.
PAGE 6
SSA-EB Series Emergency Stop Push Buttons TOP Mark Press on the terminal cover Slots Place projections on contact block 3. Press the SSA-EB1-TC terminal cover toward the contact block. Remove the SSA-EB1-TC Terminal Cover 1. Pull out the two latches on the top of the SSA-EB1-TC terminal cover. Do not exert excessive force on the latches, or the latches may break. Projections (pull) 2. Remove the SSA-EB1-TC terminal cover.
PAGE 7
SSA-EB Series Emergency Stop Push Buttons Specifications Button/Locking Collar Polyamide/Aluminum Operating Temperature Non-illuminated: –25 to +60°C (-13 to +140°F) Illuminated: –25 to +55°C (-13 to +131°F) Environmental Rating Actuator: IP65 (IEC60529) Terminal: IP20 with SSA-EB1-FSTC installed Operating Humidity 45% to 85% RH (no condensation) Insulation Resistance 100MΩ minimum (500V DC megger) Impulse Withstand Voltage 2.
PAGE 8
SSA-EB Series Emergency Stop Push Buttons Monitor Contacts (N.O.) AC 50/60 Hz DC 30V 125V 250V Resistive Load (AC-12) - 1.2A 0.6A Inductive Load (AC-14) - 0.6A 0.3A Resistive Load (DC-12) 2A 0.4A 0.2A Inductive Load (DC-13) 1A 0.22A 0.1A The operating current is classified according to JIS C 8201-5-1-1999 making and breaking capacities and are measured at resistive/inductive load types specified in IEC 60947-5-1.
PAGE 9
SSA-EB Series Emergency Stop Push Buttons a b c d 7 mm max 19 mm max 39 mm min 15 mm min4 4 Dimension d is 6 mm or more when attaching a padlock from the side of a switch P/N 168349_web Rev. B www.bannerengineering.
PAGE 10
SSA-EB Series Emergency Stop Push Buttons Mounting Hole Layout The values are the minimum dimensions for mounting with other ø 30 mm push buttons. For other control units of different sizes and styles, determine the values according to the dimensions, operation, and wiring convenience. For padlock-style lockable emergency stop push buttons, determine the values according to the size and number of padlocks and hasp. Ø30.
PAGE 11
SSA-EB Series Emergency Stop Push Buttons EM ER GENCY ST OP ESL-44/70 (1 each) ESL-44/70-10 (10 each) ww nnerengineering.c om E-Stop Legend, Label “EMERGENCY STOP” 70 mm diameter (OD) 44 mm hole for application around SSA-EB1M… w.ba • • • • EM ER GENCY ST OP U.S. Application Standards ANSI B11.0 Safety of Machinery; General Requirements and Risk Assessment ANSI B11.