ZxA1 Series Loudspeaker Owner’s Manual ZxA1-90 ZxA1-100 Electro-Voice® ZxA1 Owner’s Manual
Important Safety Instructions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. AVIS: RISQUE DE CHOC ELECTRIQUE. NE PAS OUVRIR. WARNING: CONNECT ONLY TO MAINS SOCKET WITH PROTECTIVE EARTHING CONNECTION.
FCC Information 1. IMPORTANT: Do not modify this unit! Changes or modifications not expressly approved by the manufacturer could void the user’s authority, granted by the FCC, to operate the equipment. 2. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Description Thank you for choosing the Electro-Voice ZxA1 loudspeaker system. Please take time to consult this manual so that you can understand all the features built into your EV system and fully utilize all its performance capabilities. The Electro-Voice ZxA1 powered loudspeaker is a fully integrated audio system with carefully matched electronics and transducers. This product makes it easy to setup a high quality sound system quickly with a minimum amount of cables and external electronics.
Tripod and Floor Monitor Operation Floor Monitor Electro-Voice ZxA1 loudspeakers may be used as a floor monitor by placing the speaker on the integral monitor angle. Make sure to: • Place the speaker on a level, stable surface that is solid and secure. • Route cables and position the stand so that performers, production crew and audience members will not trip over the stand or cables and pull the speaker system over. Secure cables with wire ties or tape whenever possible.
Suspending ZxA1 Loudspeakers Electro-Voice ZxA1 loudspeakers may be safely suspended with single stud fittings by using the MP1 suspension kit, or quickly attached to a truss by using the CA-Zx truss clamp adaptor (both sold seperately). See MP1 or CA-Zx instruction sheets for proper assembly and use. WARNING: Suspending any object is potentially dangerous and should only be attempted by individuals who have a thorough knowledge of the techniques and regulations of rigging objects overhead.
Rotating the 90° Horn The 90° version of the ZxA1 allows for the horn to be rotated for more effective coverage if desired. The horn is factory-installed with the 90° coverage in the horizontal plane and the 50° coverage in the vertical plane. The 100° version of the ZxA1 has the same coverage pattern in both the horizontal and vertical planes, so rotating the horn will not change the coverage pattern. To rotate the horn follow the steps below: 1. Remove the grille screws / grille assembly. 2.
Amplifier Controls Quick Setup To get the ZxA1 into operation as quickly as possible, please observe the following steps and precautions: • Make sure power switch is in the off position before plugging in power cord. • Plug the 3-terminal IEC-standard AC cable into a grounded line receptacle.
Amplifier Controls (cont’) MASTER Level control for adjusting the power amp’s overall amplification. The level control affects the volume of the line input and microphone input. To prevent distortion and clipping of pre-linked mixing consoles, the control should generally be set to a value between 0dB and +6dB. LIMIT The LED brief blinking indicates that the power amplifier is operated at its limits. Short-term blinking is uncritical, because the integrated limiter keeps distortion under control.
Dimensions Top View Right View Rear View Front View Bottom View Block Diagram 10 Electro-Voice® ZxA1 Owner’s Manual
Frequency Response Graphs ZxA1-100 Series Frequency Response 110 110 100 100 90 90 Sensitivity (dB) Sensitivity (dB) ZxA1-90 Series Frequency Response 80 70 60 50 70 60 50 40 30 80 40 Full Range Mode With Sub Mode 20 50 100 1000 10000 20000 30 Full Range Mode With Sub Mode 20 50 100 Frequency (Hz) 1000 10000 20000 Frequency (Hz) ZxA1 Models and Accessories Reference Table System Model Coverage Finish Voltage Part No.
Electro-Voice® 12000 Portland Avenue South, Burnsville, MN 55337 Phone: 952/884-4051, Fax: 952/884-0043 www.electrovoice.com © Bosch Communications Systems Part Number LIT000395 Rev 02 01/2010 U.S.A. and Canada only. For customer orders, contact Customer Service at: 800/392-3497 Fax: 800/955-6831 Europe, Africa, and Middle East only. For customer orders, contact Customer Service at: + 49 9421-706 0 Fax: + 49 9421-706 265 Other Internatonal locations.