69802 G Gas Hob AUS ERFAHRUNG GUT Operating Instructions PERFECT IN FORM AND FUNCTION GB
Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 350350 Installation z This hob must be installed by qualified personnel, according to the manufacturer’s instructions and to the relevant British Standards. z Any gas installation must be carried out by a registered CORGI installer. z Remove all packaging before using the hob.
z z z z Do not use this hob if it is in contact with water. Do not operate the hob with wet hands. Ensure the control knobs are in the ‘OFF’ position when not in use. When using other electrical appliances, ensure the cable does not come into contact with the hot surfaces of the cooking appliance. Unstable or misshapen pans should not be used on the hob as unstable pans can cause an accident by tipping or spillage. z Never leave the hob unattended when cooking with oil and fats.
Contents Important Safety Information ................................................................................ 2 Instructions for the User ........................................................................................ 5 Description of the Hob ............................................................................................... 5 Operation ....................................................................................................................
Description of the Hob 1 3 3 5 6 7 8 4 2 1. 2. 3. 4. 5. 6. 7. 8. Hob Top Rapid Burner Semi-rapid Burners Auxiliary Burner Control knob for back right burner (semi-rapid) Control knob for back left burner (semi-rapid) Control knob for front left burner (rapid) Control knob for front right burner (auxiliary) INSTALLATION Any gas installation must be carried out by a registered CORGI installer, and in accordance with existing rules and regulations.
Operation HOB BURNERS To light a burner, turn the relevant control knob anticlockwise to the maximum position, then push it down to ignite the burner. Upon, ignition, keep the knob pushed down about 5 seconds, then adjust the flame as required. If the burner does not ignite, turn the control knob to zero, and try again. Each control knob is equipped with a pilot light which gradually lights up according to the heat level that you select with the control knob.
Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. Pan Supports To keep the pan supports in the correct position, they are mounted on metal pins located in the back of the hob. After cleaning the hob, ensure the pan supports are properly placed as shown in the diagram. The pan supports are dishwasher proof.
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local AEG Service Force Centre. SYMPTOM There is no spark when lighting the gas SOLUTION The gas ring burns unevenly 8 Check that the unit is plugged in and the electrical supply is switched on Check that the RCCB has not tripped (if fitted) Check the mains fuse has not blown Check the burner cap and crown have been replaced correctly, e.g. after cleaning.
Service and Spare Parts If you require spare parts or an engineer contact your local Service Force Centre by telephoning: 0870 5 929 929 Your call will be routed to your local Service Force Centre. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www.serviceforce.co.uk When you contact the Service Centre, they will need the following information: 1. Your name, address and post code. 2. Your telephone number 3.
Guarantee Conditions Standard guarantee conditions We, AEG, undertake that if within 12 months of the date of the purchase this AEG appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our discretion repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: • The appliance has been correctly installed and used only on the electricity or gas supply stated on the rating plate.
Instructions for the Installer Instructions for the Installer Engineer technical data OVERALL DIMENSIONS Width: 580 mm. Depth: 510 mm. Height: 88 mm. Weight: 8 Kg. CUT OUT DIMENSIONS Width: 550 mm. Depth: 470 mm. Thickness: 30 mm. SUPPLY CONNECTIONS Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230-240V 50Hz supply, 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse.
Instructions for the Installer BURNER RAPID (large) TYPE OF GAS POSITION NATURAL GAS 20 mbar VALUE = 37.78 MJ/m3 Ws - 50.7 MJ/ m3 LPG GAS 28-30/37 mbar VALUE = 49.92 MJ/Kg SEMI-RAPID (medium) AUXILIARY (small) MAX MIN MAX MIN MAX 2.9 0.65 1.9 0.45 1.0 0.33 0.276 0.062 0.181 0.043 0.095 0.031 119 Adjust. 96 Adjust. 70 Adjust. NOMINAL THERMAL POWER kW 2.7 0.65 1.9 0.45 1.0 0.33 NOMINAL FLOW RATE 195 46.8 137 32.4 72 23.
Instructions for the Installer Location The hob may be located in a kitchen, a kitchen/diner or bed sitting room, but not in a bathroom or shower room. Before making the cut out in the worktop ensure that there is a minimum distance of 55 mm. between the rear edge of the hob and the wall. A minimum distance of 100 mm. must be left between the side edges of the hob and any adjacent cabinets or walls.
Instructions for the Installer FO 0814 FO 0264 A) End of shaft with nut B) Washer C) Elbow On the end of the shaft, which includes the GJ 1/2" threaded elbow, adjustment is fixed so that the washer is fitted between the components as shown in the diagram. Screw the parts together without using excessive force. Gas Connection Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or copper. The connection should be suitable for connecting to RC 1/2 (1/2 BSP male thread).
Instructions for the Installer Cut Out Size The dimensions of the cut-out are given in the diagram. Building In 51 0 0 58 Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2.
Instructions for the Installer Building over a kitchen unit with door 3 a 60 The panel fitted under the hob ("a") should be easily removable to allow easy access if technical assistance is needed. The space behind the kitchen unit ("b") can be used for connections. Fitting the hob to the worktop 20 min 30 Proper arrangements must be taken in designing the furniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated.
Instructions for the Installer Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. This hob is designed to be connected to a 230-240V 50Hz AC electrical supply.
Instructions for the Installer Permanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm. between the switch contacts and of a type suitable for the required load in compliance with the current electric regulations. The switch must not break the yellow and green earth cable at any point.
Instructions for the Installer Fault Finding Blue Brown Preliminary Electrical Systems Check START Isolate appliance and carry out: A: Earth Continuity check. NO YES Blue Green Yellow Brown Carry out: D: Resistance to Earth check. Carry out: C: Polarity check. Has inlet fuse blown? NO Electricity supply should now be satisfactory. YES PLUG (with cover removed) Earth Wire Green/Yellow Neutral Wire Blue SOCKET (face view) ( ) E( ) FUSE Inlet wiring faulty. Rectify any fault.
Instructions for the Installer A. EARTH CONTINUITY CHECK Appliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale and adjust zero if necessary. — Test leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 Ω (Ohm), check all earth wires for continuity and all contacts are clean and tight. B. INSULATION CHECK Appliance electrically disconnected, all switches ON. a) meter set on Ω (Ohms) x 1 scale. Test leads from L to N in appliance terminal block.
Instructions for the Installer Ignition System / Gas Ignition Ignitor does not spark YES Check gas supply at burner NO Check plug top fuse and replace if necessary Light burner manually Check polarity and earth continuity of supply point Check by pass simmer adjusted Check earth continuity of appliance Check position of the electrode Check fitting of burners Check continuity from 'N' on the mains connector block and "O" on the ignitor unit Check continuity from the tip of each electrode to the t
Instructions for the Installer Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. Turn the gas tap to the MAX position and ignite. ) 1)2) Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguished follow the procedure below. Procedure: the burner and set to ) 1) Re-ignite MIN. 2) Remove the control knob.
Instructions for the Installer Conversion from Natural Gas to LPG It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injectors are fitted and the gas rate is adjusted to suit. Method Ensure that the gas taps are in the 'OFF' position ) 1)2) Isolate the hob from the electricity supply 3) Remove all pan supports, burner caps, rings, crowns and control knobs.
Grafiche MDM - Forlì AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg.hausgeraete.de © Electrolux plc 2003 From the Electrolux Group. The world’s No.1 choice. The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx.