E774F402BI EN Washing Machine User Manual
www.electrolux.com CONTENTS 1. SAFETY INFORMATION....................................................................................3 2. SAFETY INSTRUCTIONS..................................................................................4 3. INSTALLATION.................................................................................................. 6 4. PRODUCT DESCRIPTION.............................................................................. 16 5. CONTROL PANEL...............................
ENGLISH 1. 3 SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference. 1.
www.electrolux.com by clients in hotels, motels, bed & breakfast and other residential type environments; – areas for communal use in blocks of flats or in launderettes. Do not exceed the maximum load of 7 kg (refer to the "Programme chart" chapter). The operating water pressure at the water entry point from the outlet connection must be between 0.5 bar (0.05 MPa) and 8 bar (0.8 MPa). The ventilation opening in the base must not be covered by a carpet, mat, or any floor covering.
ENGLISH • • • • • • • than 0°C or where it is exposed to the weather. The floor area on which the appliance is to be installed must be flat, stable, heat resistant and clean. Make sure that there is air circulation between the appliance and the floor. When the appliance is in its permanent position, check if it is levelled correctly with the aid of a spirit level. If it is not, adjust the feet accordingly. Do not install the appliance directly above a floor drain.
www.electrolux.com • Do not touch the glass door while a programme is in operation. The glass can get hot. 2.5 Service • • To repair the appliance contact an Authorised Service Centre. Use original spare parts only. 2.6 Disposal WARNING! Risk of injury or suffocation. • • • • Disconnect the appliance from the mains electrical and water supplies. Cut off the mains electrical cable close to the appliance and dispose of it.
ENGLISH 7 1. Put two polystyrene packaging elements on the floor under the appliance. WARNING! It is strongly recommended that this action is carries out by two persons. 2. Carefully put the appliance down on its rear side. Make sure not to damage the hoses. 3. Remove the polystyrene protection from the bottom. 1 2 4. Return the appliance in vertical position and remove the socket polystyrene protection. 1 2 5. Remove the power supply cable and the drain hose from the hose holders.
www.electrolux.com 6. Remove the three bolts, the hose holders and plastic spacers by using the spanner supplied with the appliance. F 7. Close the holes with the plastic caps you find in the user manual bag. Put the smallest cap F in upper hole and the two bigger caps G in lower holes. G We recommend that you keep the packaging and the transit bolts for any movement of the appliance. 3.4 Installation on suspended flooring Suspended wooden floors are particularly susceptible to vibration.
ENGLISH 3.5 Positioning and levelling 1. Install the appliance on a flat hard floor. WARNING! Make sure that carpets do not stop the air circulation below the appliance. Bring the appliance near the furniture recess before levelling it. For more details, refer to paragraph "Building in". x4 2. Loosen or tighten the feet to adjust the level. A correct adjustment of the appliance level prevents the vibration, noise and the movement of the appliance when in operation.
www.electrolux.com The inlet hose 1. Remove the inlet hose from inside the drum. 2. To connect the water inlet hose towards the proper direction and with the proper inclination, check the position of the water tap before connecting it to the back of the appliance. Make sure the hose is nor kinked, squashed but neither tensed. 45 20 O O 3. Connect the hose to the back of the appliance. Do not turn the inlet hose downwards, but turn it left or right depending on the position of your water tap. 4.
ENGLISH 11 To a stand pipe with vent-hole Directly into a drain pipe at a height of not less than 60 cm (23.6”) and not more than 100 cm (39.3”). The end of the drain hose must always be ventilated , i.e. the inner diameter of the drain pipe (min. 40 mm - min. 1.6”) must be larger than the external diameter of the drain hose. Ø 40 mm max.600 mm To a sink spigot Put the drain hose in the spigot and tighten it with the supplied cable tie L.
www.electrolux.com 596 mm If hoses run behind the appliance, make sure that nothing closes the small recess indicated with the measures 50 x 50 mm. 553 mm 819 mm 50 mm 50 mm 140 mm 76 mm Before proceeding with appliance building in, bring it near the recess and preposition the inlet hose, the drain hose and the mains cable. WARNING! Make sure they are not kinked or squashed. The appliance is also equipped with an adhesive sponge pad H that you can find inside the drum.
ENGLISH 13 1. Remove the screws of the top cover on the rear of the appliance and install the anti-tilting device as shown in the drawing. ~10mm 2. Adjust the anti-tilting device so that the distance from the counter is 10mm. Loosen the nut counterclockwise with a 3mm wrench. Adjust the height and turn the nut clockwise to fix it. 3.9 Preparation and assembly of the cupboard door The dimensions of the cupboard door should be: • width min. 595 - max. 598 mm; • thickness 16-22 mm.
www.electrolux.com Reversibility of the cupboard door Carry out the cupboard door reversibility before the appliance is built in completely. N M If the cupboard door has to be opened from left to right, invert the position of the hinge supports M with the magnetic plate N and lower plate O. O M N Make sure that the plate with magnet is on the upper position. O Cupboard door preparation For countersinking the door, it is recommended to call a professional.
ENGLISH 15 Set the position of the lower hole respecting dimensions and distances shown in the drawing (449 mm). Countersink the holes. 16-22 mm Ø 35 mm 416 mm 22±1,5 mm 14 mm 595-598 mm A Hinges To mount the hinges it is necessary to drill two holes (dia. 35 mm, depth 12.5 - 14 mm depending on the depth of cupboard door) on the inner side of the door. The hinges will be fixed to the door by means of the four supplied screws A.
www.electrolux.com Counter-magnet The appliance is pre set for a magnetic closure. For a correct closure: 1. Position the screw C and the countermagnet D on the magnetic plate N. Lean the cupboard door against the screw until it leaves a mark. 2. Open the cupboard door and screw the counter-magnet D (steel disk + rubber ring E) with the screw C in the inner side of the cupboard door, where the screw left the mark as described in the first step. 1 N 2 E D C 4. PRODUCT DESCRIPTION 4.
ENGLISH 5. CONTROL PANEL 5.1 Control panel description 1 Wool/Silk Denim Outdoor Sport Rapid 14min 2 90° 1400 Cottons Eco 60° 1200 Synthetics 40° 800 Delicates 30° Cottons Steam Rinse Spin/Drain 5 Time Manager Delay Start 20° Anti-allergy Duvet 3 4 Cold Spin Temp. 11 10 The permanent options are set by holding pressed the relative button for at least 3 seconds.
www.electrolux.com Delay start indicator. The digital indicator can show: • • Reset position ( ). Programme duration (e. g. • Delay time (e. g. • Cycle end ( ). ). ). • Warning code (e.g. • Error indicator ( ). ). Time Manager indicator. Anti-stain indicator. Extra Rinse indicator. Steam phase indicator. Add garments indicator. it lights at the beginning of the wash‐ ing phase, when it is still possible to pause the appliance and add more laundry. Child safety lock indicator.
ENGLISH 6.4 Temp. When you select a washing programme, the appliance automatically proposes a default temperature. If you touch the Start/Pause button, the appliance performs only the draining phase. The indicator Cold = cold water. The indicator of the set temperature comes on. 6.5 Spin When you set a programme, the appliance automatically sets the maximum spin speed allowed, except in Denim programme.
www.electrolux.com This option increases the programme duration. The corresponding indicator above the touch button illuminates and also stays permanently on during next cycles until this option is deactivated. 6.9 Permanent Extra Rinse With this option you can permanently have an extra rinse when you set a new programme. To activate/deactivate this option, hold the Soft Plus button pressed for 3 seconds until the indicator goes off on the display.
ENGLISH very quick cycle for a smaller lightly soiled load (max. half load recommended). the shortest cycle to freshen up a small amount of laundry. The Time Manager is available only with the programmes in the table. Synthetics ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Cottons Cottons Eco indicator 1) 21 Time Manager with steam programmes When setting a steam programme, this button allows to chose three steam levels and the programme duration is reduced accordingly: • : maximum. • : medium.
www.electrolux.com Programme Default tem‐ perature Temperature range Reference spin speed Maxi‐ mum load 1200 rpm 3 kg Synthetic items or mixed fabric items. Nor‐ mal soil. 1200 rpm 2 kg Delicate fabrics such as acrylics, viscose and mixed fabrics requiring gentler wash‐ ing . Normal soil. 1400 rpm 7 kg White cotton items. This programme re‐ moves micro-organisms thanks to a washing phase with the temperature maintained above 60°C for some minutes.
ENGLISH Programme Default tem‐ perature Temperature range Reference spin speed Maxi‐ mum load 1 kg Steam - 23 Programme description (Type of load and soil level) Cottons, Synthetics, Delicates. Short and gentle steam programme to refresh even your very delicate garments, including very delicate garments with sequins, lace etc. When treat‐ ing smaller loads, the programme duration can be further reduced by means of the Time Manager option.
www.electrolux.com Programme Default tem‐ perature Temperature range Reference spin speed 1200 rpm Outdoor 30 °C 40 °C - Cold Maxi‐ mum load Programme description (Type of load and soil level) 2 kg4) 1 kg5) Do not use fabric softener and make sure that there is no soften‐ er residue in the detergent dis‐ penser. Synthetic sport items. This programme is designed to gently wash modern outdoor sportswear and is also suitable for gym, cy‐ cling or jogging clothes or similar.
ENGLISH Programme Default tem‐ perature Temperature range Reference spin speed 1200 rpm Maxi‐ mum load 1.5 kg Wool/Silk 40 °C 40 °C - Cold 25 Programme description (Type of load and soil level) Machine washable wool, hand washable wool and other fabrics with «hand washing» care symbol6). 1) Standard programmes for the Energy Label consumption values.
www.electrolux.com ■ ■ Sport ■ ■ ■ Outdoor ■ ■ ■ Denim ■ ■ ■ Wool/Silk ■ ■ ■ Delay Start Plus Steam3) Soft Plus 2) No Spi n Spin Rapid 14min Prewash1) Programme Time Manager 26 ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 1) Prewash and Stains cannot be selected together. 2) This option is not available with temperature lower than 40 °C. 3) This option is not available with temperature lower than 40 °C. 4) If you set the No Spin option, the appliance performs draining only. 7.
ENGLISH 27 9. BEFORE FIRST USE 1. Make sure that the electrical power is available and the water tap is open. 2. Pour 2 litres of water into the detergent compartment marked by . This action activates the drain system. 3. Pour a small quantity of detergent into the compartment marked by 4. Set and start a programme for cotton at the highest temperature without any laundry in the drum. This removes all possible dirt from the drum and the tub. . 10. DAILY USE WARNING! Refer to Safety chapters. 10.
www.electrolux.com - Maximum level for quantity of liquid additives. gent. - Flap for powder or liquid deter‐ Always follow the instructions that you find on the packaging of the detergent products, but we recommend that you do not exceed the maximum indicated level ( ). This quantity will however guarantee the best washing results. After a washing cycle, if necessary, remove any detergent residue from the detergent dispenser.
ENGLISH display and the given information changes accordingly. If a selection is not possible an acoustic signal sounds and the display shows . 10.6 Starting a programme Touch the Start/Pause button to start the programme. It is not possible to start the programme when the indicator of the button is off and doesn't flash (e.g. programme dial on a wrong position). The related indicator stops flashing and stays on. The programme starts, the door is locked. The display shows the indicator .
www.electrolux.com 10.12 End of the programme 10.10 Cancelling a running programme 1. Press the button On/Off to cancel the programme and to deactivate the appliance. 2. Press the button On/Off again to activate the appliance. If the SensiCare System has completed and the water filling has already started, the new programme starts without repeating the SensiCare System. The water and the detergent are not drained out in order to avoid waste.
ENGLISH 2. Press the Start/Pause button: the appliance drains the water and spins. The option indicator Rinse Hold or disappears. If you have set Quiet and the spin speed is not changed, when you press the Start/Pause button, the appliance only drains the water. 3. When the programme is completed and the door locked indicator goes off, you can open the door. 4. Press the On/Off button for a few seconds to deactivate the appliance.
www.electrolux.com 11.3 Detergents and other treatments • • • • • Only use detergents and other treatments specially made for washing machines: – powder detergents for all types of fabric, excluding delicate. Prefer powder detergents containing bleach for whites and laundry sanitization – liquid detergents, preferably for low temperature wash programmes (60 °C max) for all types of fabric, or special ones for woollens only. Do not mix different types of detergents.
ENGLISH 12.3 Maintenance wash The repeated and prolonged use of low temperature programmes can cause detergent deposits, fluff residues, bacterial growth inside the drum and the tub. This could generate bad odours and mildew. To eliminate these deposits and clean the inner part of the appliance, run a maintenance wash regularly (at least once a month). Refer to Cleaning the drum chapter. 12.
www.electrolux.com 2. Remove the top part of the additive compartment to aid cleaning and flush it out under running warm water, to remove any traces of accumulated detergent. After cleaning, put the top part back into position. 12.7 Cleaning the drain pump WARNING! Disconnect the mains plug from the mains socket. 3. Make sure that all detergent residue is removed from the upper and lower part of the recess. Use a small brush to clean the recess.
ENGLISH 35 1. Open the pump cover. 2 1 2. Place a suitable bowl below the drain pump access to collect the water that flows out. Always keep a rag nearby to dry up any water spillages when removing the filter. 180˚ 3. Turn the filter 180 degrees in anti-clockwise direction to open it, without removing. Let the water flow out. 4. When the bowl is full of water, turn the filter back and empty the container. 5. Repeat the steps 4 and 5 until the water stops to flow out. 1 6.
www.electrolux.com 7. If it is necessary, remove fluff and objects from the filter recess. Make sure that the impeller of the pump can rotate. If it does not rotate, contact the Authorised Service Centre. 8. Clean the filter under the water tap. 2 9. Put the filter back into the special guides by turning it clockwise. Make sure that you tighten the filter correctly to prevent leakages. 1 2 10. Close the pump cover.
ENGLISH 37 12.8 Cleaning the inlet hose and the valve filter 1 2 3 45° 20° 12.9 Emergency drain If the appliance cannot drain the water, carry out the same procedure, described in 'Cleaning the drain pump' paragraph. If necessary, clean the pump. When you drain the water with the emergency drain procedure, you must activate the drain system again: 1. Put 2 litres of water in the main wash compartment of the detergent dispenser. 2. Start the programme to drain the water. 12.
www.electrolux.com 13.1 Introduction The appliance does not start or it stops during operation. First try to find a solution to the problem (refer to the table). If the problem persists, contact the Authorised Service Centre. WARNING! Deactivate the appliance before carrying out any check. In case of major problems, the acoustic signals operate, the display shows an alarm code and the Start/Pause • button may flash continuously: - The mains supply is unstable. Wait until the mains supply is stable.
ENGLISH 39 13.2 Possible failures Problem Possible solution • • • The programme does not start. • • • • • • • The appliance does not • fill with water properly. • • Make sure that the mains plug is connected to the mains socket. Make sure that the appliance door is closed. Make sure that there is no damaged fuse in the fuse box. Make sure that the Start/Pause has been touched. If the delay start is set, cancel the setting or wait for the end of countdown.
www.electrolux.com Problem Possible solution • There is water on the floor. • • • You cannot open the appliance door. • • • • • The appliance makes an unusual noise and vibrates. The programme dura‐ tion increases or de‐ creases during pro‐ gramme execution. • • Make sure that a washing programme that ends with water in tub, has been selected. Make sure that the washing programme is finished. Set the drain or the spin programme if there is water in the drum.
ENGLISH 13.3 Emergency door opening In case of power failure or functioning failure the appliance door remains locked. The washing programme continues when the power is restored. If the door remains locked in case of failure, it is possible to open it using the emergency unlock function. Before opening the door: 41 To open the door, proceed as follows: 1. Press the On/Off button to switch the appliance off. 2. Disconnect the mains plug from the mains socket. 3. Open the filter flap. 4.
www.electrolux.com Programmes Load (kg) Energy con‐ sumption (kWh) Water con‐ sumption (litre) Approxi‐ Remain‐ mate pro‐ ing mois‐ gramme ture (%)1) duration (minutes) Cottons 60°C 7 1.20 79 190 52 Cottons 40°C 7 1.00 80 180 52 Synthetics 40°C 3 0.69 72 135 35 Delicates 40°C 2 0.43 46 55 35 Wool/Silk 30°C 1.5 0.14 60 70 30 Standard 60°C cotton 7 0.93 52 250 52 Standard 60°C cotton 3.5 0.70 41 205 52 Standard 40°C cotton 3.5 0.
ENGLISH Cold water Water supply 2) Maximum Load Cotton Energy Efficiency Class Spin Speed 43 7 kg A+++ Maximum 1351 rpm 1) The appliance works correctly if the water pressure is not lower than 0.05 MPa (0.5 bar). If you cannot connect the water inlet hose to the cold water tap of the primary hydraulic sys‐ tem, connect it to your domestic cold water storage system. Make sure not to exceed a dis‐ tance of 5.02 m (16.5 ft) between the appliance inlet hose and the bottom of the water stor‐ age tank.
www.electrolux.com Remaining moisture content in % 52 The 'standard 60 °C cotton programme' and the 'standard 40 °C cotton programme' are the standard washing programmes to which the information in the label and the fiche relates, these programmes are suitable to clean normally soiled cotton laundry and they are the most efficient in terms of combined ener‐ gy and water consumption.
ENGLISH 45
www.electrolux.
ENGLISH 47
157018070-B-292018 www.electrolux.