User manual
6www.electrolux.com
CNT
CNS
KR
ID
TH
VN
EN
10.Whentheingredientshavebeenground/choppedtothedesiredconsistency,unplugtheappliance,
andremovethegrinderfromtheappliance.NOTE:Donotremovethegrinderbowldirectlyfromthe
motor base as this will cause the ingredients to spill out and expose the blade assembly.
11.Turnthegrinderupsidedownandcarefullyremovethebladeassemblybyturningitanti-clockwise.
Remove the ingredients and wash the grinder bowl (L) and blade assembly (M) in soapy water
immediately after use.
CLEANING AND CARE
12.Quick cleaning:Pourwarmwaterintothejug(D)upto750ml,addafewdropsofdetergent.Replace
thelidandoperatetheblenderforafewsecondsbyturningthespeedselector(H)tothePULSE
position briefly. Finally, remove the jug and rinse it under running water.
13. Thorough cleaning: Switch off the blender and unplug the power cord. Remove the jug (D) from the
motor base (G).
13a.Cleaning the motor base: Wipethemotorbasewithadampcloth.Never immerse the motor
base in water or clean it under running water!
13b.Cleaning the jug: Removethelid(B)andjug(D).Turnthebladeassembly(F)clockwiseand
remove it by pulling it down. Rinse the blade assembly in water and detergent. Caution! Handle
carefully, the blades are very sharp!
Thelid,jugandmeasuringcupcanbewashedinthedishwasher.Becarefulwhenre-assemblingthe
bladeassembly.Pleasesee“Gettingstarted”section,no.1forinstructionsonbladeassembly.
* Specifications vary by model
TROUBLESHOOTING
Symptom Cause Solution
Theblenderdoesnot
start.
Thecomponentsarenotxed
properly.
Check if all the components are properly
locked into position.
Thespeedselector(H)isnoton
the right position.
Choosetheappropriatespeed.Touse
PULSEfunction,makesurethespeed
selector(H)isonPULSEposition.
Thejug(D)isoverlled.
Reduce the content in the jug (D) so you do
not exceed the maximum level.
Theplugisnotproperly
connected to the power outlet.
Check the connection of the plug to the
outlet or try another outlet.
Power outage. Waituntilpoweroutageisover.
Functional problem. Contact authorized service center.
Check the circuit breaker*.
Whentheelectriccurrentis
over the setting value of the
current restorer, it will disconnect
immediately.Thisisasafety
feature.
Torestart,switchotheblenderandunplug
the power cord, allow the appliance to cool
down, and then press the red salient point.
Thenputtheplugbackintothewallsocket
and switch the appliance on again.
(RefertoFig.14)
Contents leaks from the
lid (B).
Thejug(D)isoverlled.
Reduce the content in the jug (D) so you do
not exceed the maximum level.
Thelid(B)isnotcorrectly
positioned.
Lock the lid (B) correctly on the blender
jug (D).
Leak from the base of
the blender jug (D).
Therubberseal(E)isnot
positioned correctly or is missing.
Repositiontherubberseal(E)ontheblade
assembly (F) and lock it correctly onto the
jug (D).
Thebladedoesnotturn
easily.
Pieces of food too large or too
hard.
Reducethesizeorquantityofingredients
andaddsomeliquid.