Welcome to Electrolyte! Thank you for choosing our appliance. For Customer Care support and web shop visit: For extended version of User Manual visit: Subject to change without notice. 1. SAFETY 2 2, ELECTRICAL 5 3. PARTS Supplemental 6 4. OPTIONAL 6 5.INSTALLING THE HOOD —48Mm8 14 8 14 8. CLEANING AND 1§ 8. TECHNICAL 16 10.TROUBLE 16 11.ENVIRONMENTAL 16 12 WARRANTY 17 Do not attempt to install or operate this appliance until you have read the safety instructions in this manual.
A CAUTION : CAUTION indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate injury. CHILD SAFETY Packing materials: +» Packing cartons covered with rugs, bedspreads,plastic sheets, or stretch wrap may become alright chambers and can quickly cause suffocation. * Removathsprotactivefilm coveringtheappliance before putting it into operation.
A WARNING: «+ Before servicing or cleaning the unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag,to the service panel. A CAUTION: For general ventilating use only. DO NOT use to exhaust hazardous or explosive materials or vapors.
A WARNING: fire, observe the following: +» Use an extinguisher only if: The fire department Is being called. To reduce the risk of injury to persons, in the event of a cooker top grease * Smother flames with a close-fitting lid,cookie sheet, or other metal tray, then tum off the gas boomer or the electric element. Be careful te prevent bums. If the flames. do not go out immediately, evacuate and call the fire department. * Aver pick up a flaming pan you may be burned.
Fart Qty. No. Pan oY . |< nongranular Washer 4 <> o Ash Assembly z par template 1 . Upper chimney | 3.1 10.
Tools/Materlals required + Duct tape = Wire nuts -+ Tape to mount template 6" rounded metal duct, length to slut = installation + Measuring tape = Pliers -+ Gloves to protect against sharp edges -+ Knife + Safety glasses ~ Electric drill -+ Strain relief + Spirit level + Phillips (Overdrive) # 2 screwdriver + for # 2 -+ Wire cutter/stripper -+ Masking tape -+ Hammer — Saw, Jig saw or reciprocating saw IMPORTANT ‘We recommend that three people carry aut the installation.
Removing the packaging A CAUTION Remove the carton carefully. ‘Wear gloves to protect against sharp edges. A WARNING Remove the protective film covering the product before putting Into operation. Selling Support Structures * This vent hood is heavy. Adequate structure and support must be provided in all types of Installations. Framing must support minimum 150 Ibs load. + At the hood location, adequate bracing is required to support the weight of the hood (fig.
Examples of possible ducting or air re circulation Fig (® Root ch with fishing snd cap Pipe. i [2 Circulation kit shown Pel il Solar Lessees) [] Fosse [] IMPORTANT This range hood is very heavy. Adequate structure and support must be provided in all types of installations. Step 1 « Make sure that no cables or pipes will become damaged (e.g. electric, gas, water; test the areas in question with a cable detector). Using the template, mark and drill 4 holes Into the selling.
Step 4 + Mount the truss part (2) onto the ceiling with 4 sets of long screws (6) and washers (8) (ig. » Aka aura the power cabs for the range hood is routed inside the bracket. Fig(®) Fig.(® IMPORTANT Before mounting the truss part onto the ceiling, please remove the supporting plate firstly Remember to keep these screws which will be reused in step 8. Step 5 * Depending on tha ceiling height ensure required power cable length. See the table (fig 43) below for reference.
* Loosen the 4 short screws from the junction box (fig Fig * Connect the Incoming positive, neutral and ground cables to the respective terminals. (fig.2). Fig. @ L (ve) = Black N (neutral) = White © (ground) = Goren * Mount the junction box onto the range hood using 4 short screws (flg.63). Fig. @® Step Place the exhaust duct onto the outlet and secure it with duct tape {not provided) Fig.
Step 8 Hook the hood body onto the truss, ensuring It fits properly, secure the body to the truss with 12 screws (7) then tighten it fig. £Y IMPORTANT Make sure the wire terminal passes though the hols on the air house (fig.8) £3 IMPORTANT Before hooking the hood onto the truss, please make sure the aspiration plate and filter have bean removed from the body to avoid it fall and injury to installer. Steps Connect as shown the wire terminal and the controller }.
Exhaust operation Makeup Air Local building codes may require the use of makeup air systems wham using ventilation systems greater than specified CFM of air movement. The pacified CFM varies from locale to locale. Consult your VAC professional for specific requirements in your area. Alr re circulation aeration Recirculated air: Kitchen fumes are removed and after purification are fed back inch the room through the upper ventilation openings. The purification takes place via metallic anti-grease fleeter.
Press one of the speed /% button to turn the appliance on. Button Function Press button O to switch the appliance off. Press button % for low speed. Press button ¥ for medium speed. R(t © Press button %for high speed. Press button #to set ths light to a low Intensity. Press the second time to set the light to a medium Intensity. Press the third time to set the light ta a high Intensity. Press the fourth time to turn the light off.
Cleaning A DANGER Always switch off the electricity supply at the breaker box during installation, cleaning, or maintenance. A NOTE The efficiency of the range hood depends on the cleanliness of the Intake and filters. Grease should not be allowed to accumulate on hood or filter. = IMPORTANT Clean the filter every month to prevent risk of fire. Maintenance * User service-Do not repair or replace any part of the appliance unless specifically recommended In the manual.
Power supply: 120V-60HZ Motor power: 330W Lamp power: 24W for ECVI4262AS Problem Cause Solution The appliance in not fixed properly| Aka down the appliance and check iris on the brackets. property fixed. Excessive vibration. The fan blade ls damaged. Switch offish ar Reportorial 'e appliance. Repair The fan motors noted it. | 2 CE ErvIn Light an, but fan does nat | The fan blade ls jammed. personnel only. work. The motor is damaged. LED light strip broken. Pleas call service. Both light and fan do not work.
Your appliance is covered by a one year limited warranty. For one year from your original date of purchase, Electrolyte will pay all costs for repairing or replacing any parts of this appliance that prove to ba defective in materials or workmanship when such appliance is installed, used and maintained in ‘accordance with the provided Instructions. Exclusions This warranty does not cover the following: 1. Products with original serial numbers that have been removed, altered or cannot be readily determined.
If You Need Service Neap your receipt, delivery slip, or some other appropriate payment record to establish the warranty period should service be required. If service is performed, it is in your bast interest to obtain and keep all receipts. Service under this ‘warranty must be obtained by contacting Electrolyte at the addresses or phone numbers below. This warranty only applies In the USA and Canada.