User Manual Range Hood ECVI4262AS EN 2
CONTENTS 1. SAFETY INSTRUCTIONS------------------------------------------------------------------- 2 2. ELECTRICAL REQUIREMENTS------------------------------------------------------------5 3. PARTS SUPPLIED---------------------------------------------------------------------------- 6 4. OPTIONAL ACCESSORIES--------------------------------------------------------------- 6 5. INSTALLING THE HOOD ------------------------------------------------------------------ 7 6.
CAUTION： CAUTION indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate injury. CHILD SAFETY Packing materials: Packing cartons covered with rugs, bedspreads,plastic sheets, or stretch wrap may become airtight chambers and can quickly cause suffocation. Removetheprotectivefilm coveringtheappliance before putting it into operation.
WARNING: Before servicing or cleaning the unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag,to the service panel. CAUTION: For general ventilating use only. DO NOT use to exhaust hazardous or explosive materials or vapors.
WARNING: To reduce the risk of injury to persons, in the event of a cooker top grease fire, observe the following: Smother flames with a close-fitting lid,cookie sheet, or other metal tray, then turn off the gas burner or the electric element. Be careful to prevent burns. If the flames do not go out immediately, evacuate and call the fire department. Never pick up a flaming pan - you may be burned. Do not use water, including wet dishcloths or towels - a violent steam explosion will result.
PARTS SUPPLIED No. Part Qty. No. Part Qty. 1. Range hood 1 8. Washer 8x16 4 2. Truss part 1 9. Assembly template 1 3. Upper chimney + Lower chimney 3.1 + 3.2 10. Side supporting bracket 2 4. Wire cover 1 11. Front and back supporting bracket 2 5. Wire cap 3 12. Side sponge strip 2 6. Long screws ST6x70 4 13. Front and back sponge strip 2 7. Short screw M4x10 5 OPTIONAL ACCESSORIES 8' extension chimney Elux PN:EHI08X62AS 1.
INSTALLING THE HOOD Tools/Materials required Duct tape Wire nuts Tape to mount template 6" rounded metal duct, length to suit installation Measuring tape Pliers Gloves to protect against sharp edges Knife Safety glasses Electric drill Strain relief Spirit level Phillips (Pozidrive) # 2 screwdriver + torx # 2 Wire cutter/stripper Masking tape Hammer Saw, jig saw or reciprocating saw Refer to “ Ductwork installation guidelines” chart to compute the maximum permissible length for duct runs to the outdoors (fi
Removing the packaging CAUTION IMPORTANT Remove the carton carefully. Wear gloves to protect against sharp edges. Framing must be capable of supporting 150 lbs. WARNING Fig. Remove the protective film covering the product before putting into operation. 10 1/16" Ceiling Support Structures Fig. 7 1/16" This vent hood is heavy. Adequate structure and support must be provided in all types of installations. Framing must support minimum 150 Ibs load.
Examples of possible ducting or air recirculation Fig. Recirculation kit shown NOTE 1.The center of the template must match the center of the cooktop and the edges must be parallel to the sides of the cooktop. 2.Have a suitable ladder ready so that you can easily reach up to the ceiling. Step 2 Unscrew 16 screws between the two sections of the structure.
Fig. 7 Fig. 9 IMPORTANT Step 4 Mount the truss part (2) onto the ceiling with 4 sets of long screws (6) and washers (8) (fig. 8 ). Make sure the power cable for the range hood is routed inside the bracket. Fig. 8 Before mounting the truss part onto the ceiling, please remove the supporting plate firstly (fig. 9 ). Remember to keep these screws which will be reused in step 8 Step 5 Depending on the ceiling height ensure required power cable length. See the table (fig.10 ) below for reference.
Loosen the 4 short screws from the junction box (fig. 11 ) Fig. 11 Step 6 Place the exhaust duct onto the outlet and secure it with duct tape (not provided) (fig. 14 ) Fig. 14 Connect the incoming positive, neutral and ground cables to the respective terminals. (fig. 12 ). Fig. 12 Step 7 Insert the top chimney into the truss (fig. 15 ), secure it with two screws(7).Insert the bottom chimney in its seat so that it completely covers the motor compartment and electrical connection box(fig. 16 ). Fig.
Step 8 Fig. 19 Hook the hood body onto the truss, ensuring it fits properly, secure the body to the truss with 12 screws (7) then tighten it(fig. 17 ). IMPORTANT Make sure the wire terminal passes though the hole on the air house (fig. 16 ) Fig. 17 Step 10 Install the aspiration plate to the hood body. Fit the right bracket on the aspiration plate to the right fixed hinge(fig.
Exhaust operation Fig. 22 Makeup Air Local building codes may require the use of makeup air systems when using ventilation systems greater than specified CFM of air movement. The specified CFM varies from locale to locale. Consult your HVAC professional for specific requirements in your area. Fig. 23 Air recirculation operation Recirculated air: Kitchen fumes are removed and after purification are fed back into the room through the upper ventilation openings.
OPERATION Press one of the speed turn the appliance on. Button button to Function Press button to switch the appliance off. Press button for low speed. Press button for medium speed. Press button for high speed. Press button to set the light to a low intensity. Press the second time to set the light to a medium intensity. Press the third time to set the light to a high intensity. Press the fourth time to turn the light off.
CLEANING AND MAINTENANCE Cleaning DANGER Always switch off the electricity supply at the breaker box during installation, cleaning, or maintenance. IMPORTANT Clean the filter every month to prevent risk of fire. Maintenance NOTE The efficiency of the range hood depends on the cleanliness of the intake and filters. Grease should not be allowed to accumulate on hood or filter.
TECHNICAL DATA Power supply: 120V-60HZ Motor Power: 330W Lamp power: 24W for ECVI4262AS TROUBLESHOOTING Problem Cause Solution The appliance in not fixed properly on the brackets. Take down the appliance and check it is properly fixed. Excessive vibration The fan blade is damaged. The fan motor is not fixed tightly. Light on, but fan does not work. The fan blade is jammed. The motor is damaged. Light bulb broken. Replace with a bulb with correct rating. Problem with electrical connection.
WARRANTY INFORMATION Your appliance is covered by a one year limited warranty. For one year from your original date of purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed, used and maintained in accordance with the provided instructions. Exclusions This warranty does not cover the following: 1.
If You Need Service Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period should service be required. If service is performed, it is in your best interest to obtain and keep all receipts. Service under this warranty must be obtained by contacting Electrolux at the addresses or phone numbers below. This warranty only applies in the USA and Canada.
09050102432 A (EN) September 2020
