Gas hob INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance EHG 681 35670-2703 GB
Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 950950 Installation l l l l l This hob must be installed by qualified personnel, according to the manufacturers instructions and to the relevant British Standards. Any gas installation must be carried out by a registered CORGI installer. Remove all packaging before using the hob.
Contents For the Installer For the User Important Safety Information 2 Engineers technical data 9 Description of the Hob 3 Installation 10 Operation 4 Building In 11 Maintenance and Cleaning 4 Electrical connections 12 Something Not Working? 5 Wiring Diagram 13 Service and Spare Parts 6 Fault Finding 13 Guarantee Conditions 6 Commissioning 15 Conversion from Natural Gas to LPG 15 Description of the Hob 1 2 3 6 4 1. Hob Top 5 2. Rapid Burner 3. Semi-rapid Burner 4.
Operation Hob burners a burner: FpushTo light in the relevant control knob and turn it l l l l anticlockwise to maximum position. Upon ignition, keep the knob pushed down for about 5 seconds. This will allow the "thermocouple" (Fig. 1 letter D) to be heated and the safety device to be switched off, otherwise the gas supply would be interrupted. Then adjust the flame as required. If the burner does not ignite, turn the control knob to zero, and try again.
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee.
Guarantee Conditions Electrolux Standard Guarantee Conditions We, Electrolux, undertake that if, within 12 months of the date of the purchase, this Electrolux appliance or any part thereof is proved to be defective by any reason only of faulty workmanship or materials, we will, at our option, repair or replace the same FREE OF ANY CHARGE for labour, materials or carriage on condition that: * The appliance has been correctly installed and used only on the gas and electricity supply stated on the rating plate
To contact your local Service Force Centre telephone 08705 929 929 CHANNEL ISLANDS GUERNSEY Guernsey Electricity PO Box 4 Vale, Guernsey Channel Islands GY1 3AD JERSEY Jersey Electricity Company Haut De Lorme Rue De Haut De Lorme Trinity Jersey Channel Islands JE3 5FG ISLE OF LEWIS KELSO 2, 6 & 8 Woodmarket Kelso Borders TD5 7AX 54 Claremont Street Aberdeen AB10 6RA AUCHTERMUCHTY 33a Burnside Auchtermuchty Fife KY14 7AJ BLANTYRE NORTH EAST GATESHEAD Unit 356a Dukesway Court Dukesway Gateshead
To contact your local Service Force Centre telephone 08705 929 929 LONDON & EAST ANGLIA MIDLANDS BIRMINGHAM 66 Birch Road East Wyrley Trading Estate Witton Birmingham B6 7DB BOURNE Pinfold Road Bourne PE10 9HT BRIDGNORTH 68 St.
Instructions for the Installer Engineers technical data Ignition HT Spark Spark Generator Overall dimensions Width: Depth: 580 mm. 510 mm. Ispra Control's BF 50066 230-240V 0.6 YA T 120 Spark Gap Fixed Rear Left Burner (semi-rapid) Cut out dimensions Heat Input Width: Depth: Front Left Burner (rapid) 560 mm. 480 mm.
Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). Detailed recommendations are contained in the following British Standards Codes Of Practice: B.S. 6172/ B.S. 5440, Part 2 and B.S. 6891 Current Editions. The hob should not be installed in a bed sitting room with a volume of less than 20 m3.
Gas Connection Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or copper. The connection should be suitable for connecting to RC 1/2 (1/2 BSP male thread). When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation. Ensure that the main connection pipe does not exert any strain on the hob. A) End of shaft with nut B) Washer C) Elbow FO 0264 in.
Fitting the Hob into the worktop Before fitting the hob into the cut out, a sealing gasket supplied with the hob must be fitted to the edge of the cut out. It is essential that no gaps are left in this seal in order to prevent spillage near the hob seeping into the cabinet below. F Place the sealing gasket all around the edge of the cut out. Place the hob into the cut out and secure it by means of the relevant fixing clamps and screws, as shown in the diagram. Remove the excess seal.
Wiring Diagram N 220 240 1 2 3 0 4 2 1. TAPS IGNITOR SWITCHES 1 2. IGNITOR UNIT L Fault Finding Preliminary Electrical Systems Check Blue Green Yellow Earth Wire Green/Yellow START Isolate appliance and carry out: A: Earth Continuity check. ( ) E( ) FUSE Brown SOCKET (face view) PLUG (with cover removed) Neutral Wire Blue N L Blue Brown Green Yellow NO YES Carry out: C: Polarity check. Has inlet fuse blown? YES NO Inlet wiring faulty. Rectify any fault.
Ignition System / Gas Ignition Ignitor does not spark YES Check gas supply at burner NO Check plug top fuse and replace if necessary Light burner manually Check polarity and earth continuity of supply point Check by pass simmer adjusted Check earth continuity of appliance Check position of the electrode Check continuity from 'N' on the mains connector block and "O" on the ignitor unit Check continuity from 'L' on the mains connector block and the taps ignition switches Check continuity from igni
Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. - Turn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguished follow the procedure below. Procedure: F Re-ignite the burner and set to MIN. Remove the control knob.
Grafihe MDM - Forlì CUSTOMER CARE Electrolux 55-77 High Street Slough Berkshire, SL1 1DZ Tel: 08705-950950 © Electrolux Household Appliances Limited 2000 The Electrolux Group. The worlds No.1 choice. The Electrolux Group is the worlds largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx.