Use & Care Guide Side-By-Side Refrigerator Guia de Uso y Cuidado Refrigerador de dos puertas Guide d’utilisation et d’entretien Réfrigérateur à compartiments juxtaposés 242167700 July 2011
Finding Information Please read and save this guide Table of contents Thank you for choosing Electrolux, our new premium brand in home appliances. This Use & Care Guide is part of our commitment to customer satisfaction and product quality throughout the service life of your new appliance. Safety.............................................................................. 3 Keep a record for quick reference Connecting The Water Supply.................................... 11 Finding Information.....
Safety Important safety instructions WARNING Please read all safety instructions before using your new refrigerator. Safety Precautions Do not attempt to install or operate your unit until you have read the safety precautions in this manual. Safety items throughout this manual are labeled with a Danger, Warning or Caution based on the risk type. Definitions This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Safety Electrical information WARNING You must follow these guidelines to ensure that your refrigerator’s safety mechanisms are operating correctly. • The refrigerator must be plugged into its own dedicated 115 Volt, 60 Hz., AConly electric outlet. The power cord of the appliance is equipped with a three-prong grounding plug for your protection against electrical shock hazards. It must be plugged directly into a properly grounded threeprong receptacle.
Installation This Use & Care Guide provides general operating instructions for your model. Use the refrigerator only as instructed in this Use & Care Guide. Before starting the refrigerator, follow these important first steps. Location • Choose a place that is near a grounded electrical outlet. Do Not use an extension cord or an adapter plug. Toe Grille Installation and Removal To install toe grille 1 Open both doors. Slide left and right sides of toe grille over lower hinges of refrigerator.
Installation Door opening NOTE The refrigerator doors are designed to shut by themselves within a 20 degree opening. Your refrigerator should be positioned to allow easy access to a counter when removing food. For best use of drawers and freezer baskets, the refrigerator should be in a position where both the refrigerator and freezer doors can be fully opened. Guidelines for final positioning of your refrigerator: • All four corners of the cabinet must rest firmly on the floor.
Installation Installing Shelves Your refrigerator was shipped with the shelf hanger and shelf locking clip installed in their shipping position. Below are the instructions to install the shelves in your desired locations. 4 Reinsert clips by positioning prongs on either side of the hanger hook and pushing down on the top of the clip until it fits into the slot. 1 Detach clip from the back of hanger by pushing down on the top of the clip and pulling the clip towards you.
Removing The Doors Getting through narrow spaces If your refrigerator will not fit through an entrance area, you can reduce its size by removing the doors. Check first by measuring the entrance.
Removing The Doors To remove the freezer top hinge cover: 1 Remove the two screws from each cover over the top door hinges. 2 Lift hinge cover straight up and off. 3 Detach the water tube from the connector located below the freezer door. The connector releases when you press and hold its outer sleeve inward. With the sleeve held in this position, the tube can be removed. To remove the freezer door: Adjustable Hinge (some models) 1 Detach the multi-wire cable connector located above the top hinge.
Installing Door Handles Door Handle Mounting Instructions 1 Remove handles from carton and any other protective packaging. 2 Position freezer handle end caps over upper and lower pre-installed shoulder bolts (A) that are fastened into door, ensuring the holes for the set screws are facing towards the refrigerator door. 3 While holding handle firmly against door, fasten upper and lower Allen set screws (B) with supplied Allen wrench. 4 Repeat steps 2 and 3 to install refrigerator handle.
Connecting The Water Supply WARNING To avoid electric shock, which can cause death or severe personal injury, disconnect the refrigerator from electrical power before connecting a water supply line to the refrigerator. CAUTION To Avoid Property Damage: • Copper or Stainless Steel braided tubing is recommended for the water supply line. Water supply tubing made of ¼ inch plastic is not recommended to be used.
Connecting The Water Supply IMPORTANT Plastic Water Tubing to Ice Maker Fill Tube Steel Clamp Brass Compression Nut Ferrule (Sleeve) Copper water line Water Valve Bracket Valve Inlet Water Valve Copper water line from household water supply (Include enough tubing in loop to allow moving refrigerator out for cleaning.) Figure 1 Figure 2 After connecting the water supply, refer to “How to Prime the Water Supply System” for important information about priming an empty water supply system.
Feature Overview Understanding features and terms Your Electrolux refrigerator is designed for optimal convenience and storage flexibility. Use the illustration below to familiarize yourself with product features and terminology.
Controls Wave-Touch TM IQ-Touch TM
Controls Wave-TouchTM (some models) 3rd Level: User Variable Options Your refrigerator is equipped with a Wave-TouchTM Panel user interface display. It is only necessary to touch the panel. There is no need to press with force. There are three levels of display. 1st Level: Sleep Mode Touching the options icon displays the following options: Sleep mode displays only the WATER, CUBES and CRUSHED options. Touch an icon to activate the desired dispenser mode.
Controls (-) indicators will appear on either side of the displayed temperatures. 3 Press the + or – indicator to adjust the temperature to the desired setting. The temperature display will begin to blink with the first touch. After five seconds of inactivity, the display will beep to accept the new temperature. After 10 seconds, the display times out and returns to the basic display.
Controls IQ-TouchTM (some models) factory default on off Resets all refrigerator settings such as temp, temp display and ring tones to their factory default settings. Press and hold for three seconds to turn off the cooling system to clean the refrigerator. It also turns off all dispenser functions. The temperature display will read OFF. IMPORTANT Pressing the system off icon does not turn off power to your refrigerator. You must unplug the power cord from the wall outlet.
Controls Alarms Door Ajar If the door has been left open for an extended period of time, an alarm will sound and the door ajar indicator will display on the right side of the display. The alarm is turned off by closing the door. The mute sounds key will illuminate to prompt the reset of any pending alarms. Press this key to reset any system alarms. High Temp In the event of a high temperature condition, the temperature display will display “HI”.
Storage Features Shelf features CAUTION To avoid injury from breakage, handle tempered glass shelves carefully. 5 Place top hooks of the hanger into the desired slot, and lower straight down until lower hooks rest on the ladder. 6 Reinsert clips by positioning prongs on either side of the hanger hook and pushing down on the top of the clip until it fits into the slot. NOTE Features may vary according to model.
Storage Features Shelf features (some models) Your refrigerator includes Luxury-DesignTM glass shelves, which are designed to catch and hold accidental spills. CAUTION To avoid injury from breakage, handle tempered glass shelves carefully. NOTE Features may vary according to model. You can easily adjust shelf positions in the fresh food compartments to suit your needs. The shelves have mounting brackets which attach to slotted supports at the rear of each compartment.
Storage Features Drawers Crisper humidity control Your refrigerator includes a variety of storage drawers. These drawers usually are located in fixed positions at the bottom of the fresh food compartment. Some models are supplied with soft close slides which close by themselves the last 11/2 inches of travel. Crisper drawers include a sliding control for adjusting the humidity inside the crisper. This feature can extend the life of certain fresh vegetables that keep longer in high humidity.
Storage Features Perfect Temp Drawer (some models) The Perfect Temp Drawer (PTD) was designed to keep food items at a precise temperature that is cooler, the same, or warmer than the fresh food side of the refrigerator. The PTD is shipped turned OFF. When first turned on or after a power outage the PTD may show “HI°F” if it is set to a temperature before the freezer and fresh food temperatures have stabilized.
Storage Features IMPORTANT The two drop in insulating inserts need to remain in place while the Perfect Temp Drawer is on. Removing the inserts will cause the temperature of the crispers below it to be affected. The drop in insulating inserts can be hand washed with mild soap. Do not wash in a dishwasher. Do not clean the display area of the Perfect Temp Drawer with abrasive or caustic cleaners. Wipe clean with a moist sponge.
Storage Features 4 Pull the shelf assembly forward off of the rear support pins and out of the fridge. 4 Drop the shelf down insuring that the support pins fully snap into the grooves in the shelf. 5 Reconnect the frame connector to the control unit and reinstall the drawer. Refrigerator on/off button and the Perfect Temp Drawer When the refrigerator is turned off by pressing the main Wave-Touch or IQ-Touch on/off button the Perfect Temp Drawer will also be turned off.
Storage Features To change the position of an adjustable door bin: 1 Before adjusting a bin, remove all food. 2 Grip the bin firmly with both hands and lift it upward. 3 Remove the bin. Accessories (varies by model) Can rack The can rack allows you to efficiently and securely store 12-ounce cans of beverage. A rubber liner sits behind the cans to help keep them secure. Liner may be removed for storing larger items. 4 Place the bin just above desired position.
Storage Features Soft Freeze Bin (some models) The soft freeze bin in the top of the freezer door is designed to maintain temperatures a few degrees above the freezer temperature to provide soft serve ice cream. Special item mat (some models) The innovative design of the special item mat allows you to store four (4) bottles of wine or soft drink bottles, or any item that you want to prevent moving around. NOTE Any meat to be kept longer than two (2) days should be frozen.
Automatic Ice & Water Maker/Dispenser Priming the water supply system Your refrigerator’s water supply system includes several tubing lines, an advanced water filter, a distribution valve bank, and a reserve tank to ensure ample supply to the ice and water dispenser at all times. This system needs to be completely filled with water when first connected to an external supply line. CAUTION For proper dispenser operation, recommended water supply pressure should fall between 30 psi and 100 psi.
Automatic Ice & Water Maker/Dispenser IMPORTANT Small ice cubes or ice chips jamming in the ice maker may be a sign that your water filter needs changing. If you have a side mounted ice maker you may also experience hollow cubes -- partially frozen cubes with water inside. When these cubes are harvested they break open and spill water over the other ice cubes in the ice container, forming a solid mass of ice.
Automatic Ice & Water Maker/Dispenser CAUTION NEVER use an ice pick or similar sharp instrument to break up the ice. This could damage the ice storage bin and dispenser mechanism. IMPORTANT When removing or replacing the ice bin, DO NOT rotate the auger in the ice bin. If the auger is accidentally rotated, you must realign the auger by turning it in 90 degree turns (see below) until the ice bin fits into place with the drive mechanism.
Changing The Filter Locating the filters Your refrigerator is equipped with separate water and air filtering systems. The water filter system filters all dispensed drinking water, as well as the water used to produce ice. The air filter removes odors and impurities from the refrigerator compartment. Water filter The water filter is located at the top right side of the fresh food compartment. Air filter The air filter is located at the top of the fresh food compartment next to the water filter.
Changing The Filter More about your advanced water filter The PureAdvantageTM ice and water filter system is tested and certified by NSF International to NSF/ANSI Standards 42 and 53 for the reduction of claims specified on the performance data sheet. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.
Storing Food & Saving Energy Ideas for storing foods Fresh food storage • Keep the fresh food compartment between 34° F and 40° F with an optimum temperature of 37° F. • Avoid overcrowding the refrigerator shelves, which reduces air circulation and causes uneven cooling. Fruits and vegetables • Store fruits and vegetables in crisper drawers, where trapped moisture helps preserve food quality for longer time periods.
Normal Operating Sounds & Sights Understanding the sounds you may hear Your new, high-efficiency refrigerator may introduce unfamiliar sounds. These sounds normally indicate your refrigerator is operating correctly. Some surfaces on floors, walls, and kitchen cabinets may make these sounds more noticeable. Following is a list of major components in your refrigerator and the sounds they can cause: A Evaporator Refrigerant through the evaporator may create a boiling or gurgling sound.
Care & Cleaning Protecting your investment Keeping your refrigerator clean maintains appearance and prevents odor build-up. Wipe up any spills immediately and clean the freezer and fresh food compartments at least twice a year.
Care & Cleaning Care & cleaning tips Part Interior & Door Liners Door Gaskets Drawers & Bins Glass Shelves Toe Grille Exterior & Handles Cleaning Agents • Soap and water • Baking soda and water • Soap and water • Soap and water • Soap and water • Glass cleaner • Mild liquid sprays • Soap and water • Mild liquid sprays • Vacuum attachment • Soap and water • Non abrasive glass cleaner Exterior & Handles (Stainless Steel Models Only) • Soap and water • Stainless steel cleaners User Interface Panel • S
Care & Cleaning Replacing LED Lights Both the freezer and fresh food compartments of your refrigerator include LED lights. Always use Electrolux parts for replacement. To replace LED Lights: 1 Unplug your refrigerator’s power cord. 2 Remove light cover by pushing up and out. 3 Hold the LED cover with one hand and pull the connector with the other hand while pressing the connector latch.
Warranty Major Appliance Warranty Information Your appliance is covered by a one year limited warranty. For one year from your original date of purchase, Electrolux will repair or replace any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed, used, and maintained in accordance with the provided instructions.
Before You Call Before you call... If you experience a problem with your refrigerator or notice a product behavior or condition you do not understand, you can usually avoid a call to your service representative by referring to this section for an answer. Beginning with the following table, this information includes common problems, causes, and suggested solutions. Running Your Refrigerator Concern Compressor does not run. Refrigerator runs too much or too long. Compressor does not run.
Before You Call Temperatures Are Too Warm Concern Freezer/ Refrigerator temperature is too warm. Freezer temperature is too warm. Refrigerator temperature is satisfactory. Refrigerator temperature is too warm. Freezer temperature is satisfactory. Temperature in the Meat Keeper is too warm (some models). Cause Solution • Freezer control is set too warm. • Set freezer control to a colder setting. Allow 24 hours for temperature to stabilize. • Refrigerator control is set too warm.
Before You Call Automatic Ice Maker Concern Ice maker is not making any ice. Ice maker is not making enough ice. Ice maker will not stop making ice. Ice maker is not separating the ice cubes. Ice has bad odor and taste. Cause • Ice maker power switch is Off. • Water supply is not connected to refrigerator. • Household water line valve is not open. • Freezer is not cold enough. • Household water line to the refrigerator is kinked.
Before You Call Ice Dispenser Concern Dispenser will not dispense ice. Cause • Water supply is not connected. • Household water line to the refrigerator is kinked. • Ice storage container is empty. • Freezer temperature is set too warm. • Household water line valve is not open. • Freezer door is not closed. Ice dispenser is jammed. • Ice dispensing arm has been held in for more than 4-5 minutes.
Before You Call Water Dispenser Concern Dispenser will not dispense water. Cause • Water supply is not connected. • Household water line to the refrigerator is kinked. • Household water line valve is not open. • Freezer door is not closed. Water has an odd taste and/or odor. Water dispenses slowly. • Ice & water filter cartridge is clogged. • Front filter not fully installed, if equipped • Water has been in the tank for a period of time. • Unit not properly connected to cold water line.
Before You Call LED Light Is Not On Concern LED light is not on. Cause • LED light is burned out. • No electric current is reaching refrigerator. • Control system has disabled lights because one or both doors were left open too long. Solution • See Replacing LED Lights in Care and Cleaning section. • See Problem section, Running Your Refrigerator. • Close and reopen door(s) to enable lights.
