EN FRONT LOAD WASHER INSTALLATION INSTRUCTIONS FR LAVEUSE Á CHARGEMENT FRONTAL INSTRUCTIONS D’INSTALLATION ES LAVADORA DE CARGA FRONTAL INSTRUCCIONES DE INSTALACIÓN 157029900 May 2020
Important Safety Instructions WARNING Please read all instructions before using this washer. Recognize safety symbols, words and labels Safety items throughout this manual are labeled with a WARNING or CAUTION based on the risk type as described below: Definitions This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
Important Safety Instructions WARNING FIRE HAZARD For your safety the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury or loss of life. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. WARNING SUFFOCATION HAZARD Recycle the carton and dispose of the plastic bags after the washer is unpacked. Children might use them for play.
Installation Requirements Please Read and Save this Questions? Guide Toll-free telephone and online support: Thank you for choosing Electrolux, the premium brand in home appliances. These Installation Instructions are part of our commitment to customer satisfaction and product quality throughout the life of your new appliance. U.S. :1-877-4ELECTROLUX (1-877-435-3287) www.electroluxappliances.com Canada: 1-800-265-8352 www.electroluxappliances.
Installation Requirements Electrical system requirements CIRCUIT - Individual, properly polarized and grounded 15 amp. branch circuit fused with 15 amp. time delay fuse or circuit breaker. POWER SUPPLY - 2 wire, with ground, 120 volt single phase, 60 Hz, Alternating Current.
Installation Requirements Water supply requirements Power Receptacle Hot and cold water faucets MUST be installed within hose length of your washer’s water inlet. The faucets MUST be 3/4 inch (1.9 cm) with threading for laundry hose connection. Water pressure MUST be between 10 and 110 psi. Pressure difference between hot and cold cannot be more than 10 psi. Your water department can advise you of your water pressure.
Installation Instructions to clear open door 24" (60.5 cm) 26" (66 cm) electrical supply on rear of unit3 water supply connection on rear of unit power cord on rear of unit2 68.5" (174 cm) drain hose on rear of unit1 floor line Drain hose length on washer approximately 55 inches (140 cm). Power supply cord length on washer approximately 59 inches (150 cm). Power supply cord length on Canadian dryer approximately 59 inches (150 cm).
Installation Instructions 1. Remove door tape and empty drum contents, including foam shipping brace inside rubber gasket of door. 2. Using a foam corner post from the packaging to protect the floor, carefully lay the washer on its back. Releasing drain hose The drain hose is secured in place with two plastic latching clamps. Press the locking tab and release the drain hose. CAUTION EXCESSIVE WEIGHT HAZARD To avoid back or other injury, have more than one person move or lift the washer.
Installation Instructions Installing hole plugs Connecting inlet water Locate hole plugs in the small bag supplied with washer instruction guides. Cut them apart from each other and insert them in the holes in washer back panel. 1. Run some water from the hot and cold faucets to flush the water lines and remove particles that might clog the water valve screens and to determine which faucet is hot and which is cold supply.
Installation Instructions 3. Connect the HOT inlet hose to the HOT water supply and the COLD inlet hose to the COLD water supply. Tighten by hand until snug. Then tighten each supply connection another 2/3 turn with pliers. Do not bend, kink or pinch water inlet hoses. 4. Turn on the water and check for leaks. 2. Place the hook end of the drain hose in the drain opening. Secure the drain hose with the cable tie (provided in the enclosure package) to the standpipe, inlet hose, laundry tub, etc.
Accessories 11 4. Turn on the power at a circuit breaker/fuse box. 5. Carefully slide the washer to its final position. Recheck for level and rock corners for stability. Remove and discard door tape. Replacement parts: If replacements parts are needed for your washer, contact the source where you purchased your washer or refer to your Use & Care Guide for more information. WARNING ELECTRICAL SHOCK HAZARD Label all wires prior to disconnection when servicing controls.
electrolux.
